version 0.7 not update 0.7 R3

[arlaor]

Hi @karawin I use wemos lolin32 board I am trying to update the version to be able to listen in vs1053, but it does not update the new version. I tried to upload the bin file again with the esp32 download tool, to update to the R3 version, but only the 0.7 version still appears. version 0.7 does not allow me to play stations with AAC extension, I do not have sound in my speaker. I have used the pins suggested in the image, but I can not get it working. The following shows it in the arduino IDE

CLI.STOPPED# from unsupported mime type

CLI.STOPPED# from OTA

Starting update ... must receive:770384 bytes

Connection closed, all packets received Total Write binary data length : 770384 Update firmware succeded. Restarting ets Jun 8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0018,len:4 load:0x3fff001c,len:2980 load:0x40078000,len:0 load:0x40078000,len:11400 entry 0x40078c38 I (324) main: starting app_main() I (324) main: RAM left: 171968 E (324) main: Running partition type 0 subtype 16 (offset 0x00010000) I (354) main: Partition init done... Log level is now ESP_LOG_ERROR E (5464) vs1053: VS1053/VS1003 detected. Version: 0 device: 3ffc9e7c volume: 128 E (5784) wifi: esp_wifi_disconnect 844 wifi not start

DNS: 192.168.1.254
IP: 192.168.1.60

Init .................... Done autostart: playing:1, currentstation:2

CLI.NAMESET#: 2 80srock RR (rockradio.com) aac 128 kbps

CLI.URLSET#: prem3.rockradio.com

CLI.PATHSET#: /80srock_aac?a75b7607061c2551c187ccbe

CLI.PORTSET#: 80

CLI.OVOLSET#: 0

CLI.VOL#: 128

CLI.ICY0#: 80s Rock - ROCKRADIO.COM Premium

CLI.ICY3#: http:\/\/www.rockradio.com

CLI.ICY4#: Rock 80s Classic

CLI.ICY5#: 128

CLI.ICY7#: ice-bitrate=128

CLI.PLAYING

CLI.META#: Bruce Springsteen - My Hometown

E (17284) audio_player: failed to start decoder task

CLI.STOPPED# from unsupported mime type

CLI.NAMESET#: 1 80 HotMixRadio (80's) mp3 128 kbps

CLI.URLSET#: streaming.hotmix-radio.net

CLI.PATHSET#: /hotmixradio-80-128.mp3

CLI.PORTSET#: 80

CLI.OVOLSET#: 0

CLI.VOL#: 128

CLI.ICY0#: Hotmixradio 80

CLI.ICY3#: http:\/\/www.hotmixradio.fr\/80

CLI.ICY4#: 80s

CLI.ICY5#: 128

CLI.ICY7#: ice-samplerate=44100;ice-bitrate=128;ice-channels=2

CLI.PLAYING

CLI.META#: SCORPIONS - Still Loving You

CLI.STOPPED# from Player stop

CLI.NAMESET#: 6 alternativerock RR (rockradio.com) aac 128 kbps

CLI.URLSET#: prem3.rockradio.com

CLI.PATHSET#: /alternativerock_aac?a75b7607061c2551c187ccbe

CLI.PORTSET#: 80

CLI.OVOLSET#: 0

CLI.VOL#: 128

CLI.ICY0#: Alternative Rock - ROCKRADIO.COM Premium

CLI.ICY3#: http:\/\/www.rockradio.com

CLI.ICY4#: Alternative Rock

CLI.ICY5#: 128

CLI.ICY7#: ice-bitrate=128

CLI.PLAYING

CLI.META#: Muse - Uprising

E (1196264) audio_player: failed to start decoder task

CLI.STOPPED# from unsupported mime type

[karawin]

Something is wrong on the spi bus E (5464) vs1053: VS1053/VS1003 detected. Version: 0 Show that nothing is read even if the DREQ line is good (vs detected) Please check

define PIN_NUM_MISO GPIO_NUM_19 // Master Input, Slave Output

define PIN_NUM_MOSI GPIO_NUM_23 // Master Output, Slave Input Named Data or SDA or D1 for oled

define PIN_NUM_CLK GPIO_NUM_18 // Master clock Named SCL or SCK or D0 for oled

[arlaor]

hi @karawin I have reviewed the connections and are consistent with those provided in the image of your publication. And how can I solve the impace of not being able to update to the new version R3?

[karawin]

You ar in R3 after the update. Type sys.version to see I cannot say why it doesn't work on your board. Please details the wires from the vs1053 to the esp32 including the Vcc and gnd. How is powered your boards? etc.

[arlaor]

Hi @karawin powered in my board is my laptop port usb 5V command sys.version see "low memory"

[karawin]

this is the answer of the http interface. Type sys.version on telnet or uart interface. And please answer to all questions if you need help. Please details the wires from the vs1053 to the esp32 including the Vcc and gnd.

[arlaor]

hi @karawin Sorry tonight when I'm at home, I'll try to learn how to use telnet, to be able to verify the version. I will also send an image with the connections. The voltage for the vs1053 I'm getting directly from the wemos lolin32, using the 5V pin and GND. in my ESP8266, I have it connected in the same way and it works. Tonight I will complement the information Thanks

[arlaor]

Hi @karawin Attach Image

[karawin]

First of all, do an OTA to the 0.8 release, On restart type: sys.logi sys.lcd("255")

to the uart interface, the reset. You must see more or less

I (11) main: starting app_main() I (11) main: RAM left: 171040 E (11) main: Running partition type 0 subtype 16 (offset 0x00010000) I (41) main: Partition init done... Log level is now ESP_LOG_INFO E (2961) vs1053: VS1053/VS1003 detected. MP3Status: 40, Version: 4 I (2961) vs1053: SCI_Status = 0x40 I (2961) vs1053: SCI_Mode (0x4800) = 0x4802 I (2961) vs1053: SCI_ClockF = 0xB800 I (2961) vs1053: VS Version (VS1053 is 4) = 4 device: 3ffcd6d8 I2S Speed: 0 I (2971) VS1053 Patches: plugin size 6350 3175 I (2971) VS1053 Patches: plugin start: 7 1 8050 6

I (3311) VS1053 Patches: plugin size 234 117 I (3311) VS1053 Patches: plugin start: 7 1 8f00 6

volume: 64 I (3421) main: hardware initialized I (3421) main: Hardware init done... E (3421) main: LCD Type 255 I (3421) main: audio_output_mode 4 One of I2S=0, I2S_MERUS, DAC_BUILT_IN, PDM, VS1053 I (3421) main: Set baudrate at 115200 I (3431) main: Release 0.8, Revision 0 I (3431) main: SDK v3.0-dev-1024-g92748142-dirty I (3441) main: Heap size: 165896 I (3441) main: t0 task: 3ffcfa44 I (3441) main: starting wifi I (3451) wifi: wifi firmware version: 111e74d I (3451) wifi: config NVS flash: enabled I (3451) wifi: config nano formating: disabled I (3481) wifi: Init dynamic tx buffer num: 32 I (3481) wifi: Init data frame dynamic rx buffer num: 32 I (3481) wifi: Init management frame dynamic rx buffer num: 32 I (3481) wifi: wifi driver task: 3ffd3a1c, prio:23, stack:4096 I (3481) wifi: Init static rx buffer num: 10 I (3491) wifi: Init dynamic rx buffer num: 32 I (3491) wifi: Init rx ampdu len mblock:7 I (3501) wifi: Init lldesc rx ampdu entry mblock:4 I (3501) wifi: wifi power manager task: 0x3ffd8e88 prio: 21 stack: 2560 E (3511) wifi: esp_wifi_disconnect 844 wifi not start I (3511) main: connecting I (3541) wifi: mode : sta (24:0a:c4:82:ec:60) I (3541) main: Initialised wifi I (3661) wifi: n:11 2, o:1 0, ap:255 255, sta:11 2, prof:1 I (4651) wifi: state: init -> auth (b0) I (4651) wifi: state: auth -> assoc (0) I (4661) wifi: state: assoc -> run (10) I (4671) wifi: connected with karawin2, channel 11

DNS: 192.168.1.70
IP: 192.168.1.210

I (4841) main: RAM left 113380 I (4841) main: uartInterfaceTask task: 3ffdc5dc I (4841) main: clientTask task: 3ffdd044 I (4841) servers: watermark: 0x7c8 1992 I (4841) main: serversTask task: 3ffddd38 I (4841) servers: telnetServer_sock socket: 4096, errno: 0 I (4841) addon: event_ir: 3ffdf220 I (4851) servers: Webserver socket: 4097, errno: 0 I (4851) addon: event_lcd: 3ffdf4a8 I (4841) main: task_addon task: 3ffdf0b8 Init ............... Done autostart: playing:0, currentstation:13 I (7661) wifi: pm start, type:0

Important parts are E (2961) vs1053: VS1053/VS1003 detected. MP3Status: 40, Version: 4 I (2961) vs1053: SCI_Status = 0x40 I (2961) vs1053: SCI_Mode (0x4800) = 0x4802 I (2961) vs1053: SCI_ClockF = 0xB800 I (2961) vs1053: VS Version (VS1053 is 4) = 4

To see if the vs1053 is fully detected. Another part I (3691) main: audio_output_mode 4 One of I2S=0, I2S_MERUS, DAC_BUILT_IN, PDM, VS1053 Show that the vs1053 is selected for output. If not, go to the setting of the web page and select it.

Important: if the vs1053 is not in version 3 or 4, the output mode fall back to 0 I2S.

[arlaor]

Hi @karawin the version of my VS1053 is shown as 0, so I suppose it fails with your project. My vs1053, works with your version for the esp8266 and with the version for the ESP32-Radio from edzelf

E (386892) wifi: esp_wifi_connect 836 wifi not start ets Jun 8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0018,len:4 load:0x3fff001c,len:2980 load:0x40078000,len:0 load:0x40078000,len:11400 entry 0x40078c38 I (12) main: starting app_main() I (12) main: RAM left: 171040 E (12) main: Running partition type 0 subtype 17 (offset 0x001d0000) I (42) main: Partition init done... Log level is now ESP_LOG_ERROR E (2942) vs1053: VS1053/VS1003 detected. MP3Status: 0, Version: 0 device: 3ffca2ac volume: 108 E (3042) main: LCD Type 0 E (4832) main: No vs1053 detected. Fall back to I2S mode E (5132) wifi: esp_wifi_disconnect 844 wifi not start

CLI.PATHSET#: /CARACOL_RADIOAAC.aac

CLI.PORTSET#: 80

CLI.OVOLSET#: 50

CLI.VOL#: 120

CLI.ICY0#:

CLI.ICY3#:

CLI.ICY4#: Misc

CLI.ICY5#: 32

CLI.ICY6#:

CLI.PLAYING

E (82522) audio_player: failed to start decoder task

CLI.STOPPED# from unsupported mime type

[karawin]

I can only confirm that it works with your vs1053 board type

[arlaor]

Hi @karawin

I understand you, I will perform tests with a module mini live esp32. Thanks

[karawin]

news?

[arlaor]

Hi @karawin

unfortunately I have misplaced the two board mini esp-32, so I will perform tests again on the plate lolin32. In a few moments I tell you how I'm doing with the tests

[arlaor]

perform tests with another board vs1053, which is working normally with the esp8266, but the message is the same

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0018,len:4 load:0x3fff001c,len:2980 load:0x40078000,len:0 load:0x40078000,len:11400 entry 0x40078c38 I (33) main: starting app_main() I (33) main: RAM left: 169848 E (33) main: Running partition type 0 subtype 17 (offset 0x001d0000) I (63) main: Partition init done... Log level is now ESP_LOG_ERROR

E (1663) vs1053: NO VS1053 detected

E (1663) main: LCD Type 0 E (3253) main: No vs1053 detected. Fall back to I2S mode WIFI TRYING TO CONNECT TO SSID 1 E (3463) wifi: esp_wifi_disconnect 847 wifi not start E (4673) event: invalid static ip E (4683) main: Wifi connected

DNS: 192.168.1.1
IP: 192.168.1.160

Init ............... Done autostart: playing:1, currentstation:1 READY. Type help for a list of commands

CLI.NAMESET#: 1 80 HotMixRadio (80's) mp3 128 kbps

CLI.URLSET#: streaming.hotmix-radio.net

CLI.PATHSET#: /hotmixradio-80-128.mp3

CLI.PORTSET#: 80

CLI.OVOLSET#: 0

CLI.VOL#: 100

CLI.ICY0#: Hotmixradio 80

CLI.ICY3#: http:\/\/www.hotmixradio.fr\/80

CLI.ICY4#: 80s

CLI.ICY5#: 128

CLI.ICY7#: ice-samplerate=44100;ice-bitrate=128;ice-channels=2

CLI.PLAYING

CLI.META#: P. LION - Happy Children

[karawin]

Try the last 0.9 RELEASE with more error messages.

Detection is done with the dreq line. Check it and check the + and gnd.

[arlaor]

I have tried the same cables connected to a board esp8266 and to the board vs1053 and they work normally. The tests in esp32, I made them with version 0.9 R1

[karawin]

if (VS1053_checkDREQ() == 0)
{
    vsVersion = 0; 
    ESP_LOGE(TAG,"NO VS1053 detected");
    return;
} 

with uint8_t VS1053_checkDREQ() { return gpio_get_level(PIN_NUM_DREQ); }

define PIN_NUM_DREQ GPIO_NUM_34

check the dreq with a voltmeter or oscillo. must be 3.3v

And i am sure it works. So no other idea

[arlaor]

I had saved my multimeter for a while with the batteries and these have been damaged and damaged the multimeter, so I do not have to exactly measure the voltage of pin 34. I used a led connected to GND and pin 34 and it turns on, but I do not know exactly what voltage is receiving, I only know that it is receiving voltage pin 32, 33 y 34 are receiving voltage, this pins turn on the led

If these lines are not yet implemented I think it is a good option to recognize the vs1053

if (VS1053_checkDREQ() == 0) { vsVersion = 0; ESP_LOGE(TAG,"NO VS1053 detected"); return; } with uint8_t VS1053_checkDREQ() { return gpio_get_level(PIN_NUM_DREQ); }

define PIN_NUM_DREQ GPIO_NUM_34

[karawin]

this code is part of the 0.9 release. test the connector welds May be? https://github.com/espressif/arduino-esp32/issues/729

[arlaor]

Hi @karawin

precisely that board lolin 32 has some error. The test I did was to change the feed from the 5v pin of the lolin32 to the 3v pin and the detected vs1053 message appears, but a few moments later it stops recognizing it. I guess 3V is not enough for the board vs1053.

So I took another Lolin32 board and it worked correctly. I thought that because WEMOS is the manufacturer, I would get a better product, but this brand is not a guarantee, unfortunately. Thank you

[karawin]

Could you close it?

[arlaor]

Hi @karawin Yes i do, thank you