karawin
commented
5 years ago Please OTA again, and send the log in level i (sys.logi)
Closed Hans-JR closed 5 years ago
karawin
commented
5 years ago Please OTA again, and send the log in level i (sys.logi)
Hans-JR
commented
5 years ago OK, did OTA again. Same Problem with patch loaded.
Attached are two logfiles. One with and one without patch.
From: KaraWin [mailto:notifications@github.com] Sent: Tuesday, February 19, 2019 7:35 PM To: karawin/Ka-Radio32 Ka-Radio32@noreply.github.com Cc: Elbskipper hans@richter-dollern.de; Author author@noreply.github.com Subject: Re: [karawin/Ka-Radio32] Release 1.9R0, Problem with VS1053 (#96)
Please OTA again, and send the log in level i (sys.logi) — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/karawin/Ka-Radio32/issues/96#issuecomment-465255474 , or mute the thread https://github.com/notifications/unsubscribe-auth/AkLGsSgc6Y9cJj5ineG9bzv6kfpjWs0xks5vPEPrgaJpZM4a_qoZ .
ets Jun 8 2016 00:22:57
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0018,len:4 load:0x3fff001c,len:3580 load:0x40078000,len:9300 load:0x40080400,len:5764 entry 0x400806d4 E (572) spiram: SPI RAM enabled but initialization failed. Bailing out. I (136) main: starting app_main() I (136) main: RAM left: 200488 E (136) main: Running partition type 0 subtype 16 (offset 0x00010000) I (156) main: Partition init done... Log level is now ESP_LOG_INFO I (366) vs1053: VS1053 LFreq: 1403508 I (366) vs1053: VS1053 HFreq: 6153846 I (4266) vs1053: VS1053/VS1003 detected. MP3Status: 40, Version: 4 I (4266) vs1053: SCI_Status = 0x40 I (4266) vs1053: SCI_Mode (0x4800) = 0x4802 I (4266) vs1053: SCI_ClockF = 0xB800 I (4266) vs1053: VS Version (VS1053 is 4) = 4 I (4266) vs1053: I2S Speed: 0 I (4276) VS1053 Patches: plugin size 8896 4448 I (4276) VS1053 Patches: plugin start: 7 1 8050 6
I (4616) vs1053: volume: 42 I (4616) main: hardware initialized I (4616) main: Hardware init done... I (4636) main: LCD Type 192 I (4666) addonucg: lcd init type: 192, Rotat: 0 I (4716) ucg_hal: UCG_COM_MSG_POWER_UP: 80 ns so in Hz: 12500000 I (4716) ucg_hal: ... Adding spi lcd bus Speed= 25000000. I (4836) addonucg: lcd init Color type: 192 I (4896) addonucg: X: 160, yy: 128, y: 10
I (4906) main: audio_output_mode 4 One of I2S=0, I2S_MERUS, DAC_BUILT_IN, PDM, VS1053 I (4906) main: Set Song buffer to 50k I (4906) main: Set baudrate at 115200 I (4906) main: Release 1.9, Revision 0 I (4906) main: SDK v3.3-beta1-268-g5c88c5996-dirty I (4916) main: Heap size: 139020 I (5266) main: Volume set to 42 I (5296) main: t0 task: 3ffb1a88 I (5296) main: starting wifi I (5306) wifi: wifi driver task: 3ffbd558, prio:23, stack:3584, core=0 I (5306) wifi: wifi firmware version: 38e2484 I (5306) wifi: config NVS flash: enabled I (5306) wifi: config nano formating: disabled I (5326) wifi: Init dynamic tx buffer num: 32 I (5326) wifi: Init data frame dynamic rx buffer num: 32 I (5326) wifi: Init management frame dynamic rx buffer num: 32 I (5326) wifi: Init static tx buffer num: 16 I (5336) wifi: Init static rx buffer size: 1600 I (5336) wifi: Init static rx buffer num: 10 I (5346) wifi: Init dynamic rx buffer num: 32 WIFI TRYING TO CONNECT TO SSID 2 E (5346) wifi: esp_wifi_disconnect 964 wifi not start I (5366) main: connecting I (5426) wifi: mode : sta (3c:71:bf:8c:01:78) I (5426) main: Initialised wifi I (5556) wifi: new:<11,0>, old:<1,0>, ap:<255,255>, sta:<11,0>, prof:1 I (6226) wifi: state: init -> auth (b0) I (6226) wifi: state: auth -> assoc (0) I (6236) wifi: state: assoc -> run (10) I (6256) wifi: connected with HomeLan, channel 11, bssid = c8:0e:14:f3:c4:47 I (6256) wifi: pm start, type: 1
E (6256) event: invalid static ip I (6256) main: Wifi connected
DNS: 192.168.178.1 IP: 192.168.178.58
I (7646) main: mDNS Init ok E (7646) main: mDNS Hostname: karadio32 I (7646) renderer: chip revision 1 I (7676) renderer: i2s intr:0 I (8006) main: RAM left 69180 I (8006) main: uartInterfaceTask task: 3ffb8b50 I (8016) main: clientTask task: 3ffb8cd4 I (8026) servers: watermark: 0xab8 2744 I (8026) servers: telnetServer_sock socket: 52, errno: 0 I (8026) servers: Webserver socket: 53, errno: 0 I (8026) main: serversTask task: 3ffe91a8 I (8036) main: task_addon task: 3ffea0c4 W (8106) GPIO: g_get_adc err 0x1102 I (8106) addon: rmt_nec_rx_task task: 3ffeac44 I (8106) addon: task_lcd task: 3ffeb648 I (8636) main: Init Done READY. Type help for a list of commands
autostart: playing:1, currentstation:5
I (10486) webserver: playstationInt: 5, g_device: 5 I (11016) webclient: Webclient socket: 56, errno: 0
I (12326) webclient: watermark : 3c0 960 I (12326) webclient: Webclient socket: 57, errno: 0
I (21146) audio_player: Buffer fill 3%, 1859 // 51200 bytes I (38866) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (57346) audio_player: Buffer fill 3%, 1847 // 51200 bytes
I (76106) audio_player: Buffer fill 4%, 2199 // 51200 bytes
I (94876) audio_player: Buffer fill 3%, 1648 // 51200 bytes I (113756) audio_player: Buffer fill 2%, 1164 // 51200 bytes
I (132776) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (151546) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (170466) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (189226) audio_player: Buffer fill 1%, 938 // 51200 bytes
I (208256) audio_player: Buffer fill 2%, 1387 // 51200 bytes I (227186) audio_player: Buffer fill 1%, 571 // 51200 bytes I (245926) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (264656) audio_player: Buffer fill 3%, 1648 // 51200 bytes I (283826) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (302596) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (321386) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (340446) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (359346) audio_player: Buffer fill 4%, 2259 // 51200 bytes
I (378116) audio_player: Buffer fill 1%, 567 // 51200 bytes I (396886) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (416016) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (434756) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (453556) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (472456) audio_player: Buffer fill 1%, 527 // 51200 bytes I (491486) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (510226) audio_player: Buffer fill 2%, 1435 // 51200 bytes I (529126) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (547896) audio_player: Buffer fill 3%, 1648 // 51200 bytes I (566666) audio_player: Buffer fill 3%, 1568 // 51200 bytes I (585726) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (604626) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (623366) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (642426) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (661296) audio_player: Buffer fill 3%, 1847 // 51200 bytes I (680096) audio_player: Buffer fill 1%, 959 // 51200 bytes I (699156) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (717896) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (736646) audio_player: Buffer fill 2%, 1436 // 51200 bytes
I (755506) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (774306) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (793146) audio_player: Buffer fill 3%, 1847 // 51200 bytes I (812236) audio_player: Buffer fill 1%, 740 // 51200 bytes I (831006) audio_player: Buffer fill 4%, 2260 // 51200 bytes I (849846) audio_player: Buffer fill 4%, 2094 // 51200 bytes I (868616) audio_player: Buffer fill 3%, 1648 // 51200 bytes I (887676) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (906576) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (925346) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (944406) audio_player: Buffer fill 2%, 1436 // 51200 bytes
I (963306) audio_player: Buffer fill 4%, 2259 // 51200 bytes I (982076) audio_player: Buffer fill 3%, 1647 // 51200 bytes I (1000846) audio_player: Buffer fill 2%, 1149 // 51200 bytes I (1020006) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1038806) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1057676) audio_player: Buffer fill 1%, 943 // 51200 bytes I (1076716) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1095476) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1114346) audio_player: Buffer fill 4%, 2259 // 51200 bytes I (1133116) audio_player: Buffer fill 1%, 711 // 51200 bytes I (1151886) audio_player: Buffer fill 2%, 1149 // 51200 bytes I (1171046) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1189816) audio_player: Buffer fill 2%, 1436 // 51200 bytes
I (1208656) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1227456) audio_player: Buffer fill 1%, 525 // 51200 bytes I (1246516) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1265386) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1284186) audio_player: Buffer fill 2%, 1149 // 51200 bytes I (1303216) audio_player: Buffer fill 2%, 1385 // 51200 bytes I (1322116) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1340916) audio_player: Buffer fill 1%, 635 // 51200 bytes I (1359946) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1378816) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1397526) audio_player: Buffer fill 2%, 1436 // 51200 bytes
I (1416426) audio_player: Buffer fill 4%, 2259 // 51200 bytes I (1435226) audio_player: Buffer fill 3%, 1567 // 51200 bytes I (1454256) audio_player: Buffer fill 1%, 745 // 51200 bytes I (1473126) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1491906) audio_player: Buffer fill 4%, 2260 // 51200 bytes I (1510696) audio_player: Buffer fill 1%, 943 // 51200 bytes I (1529826) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1548566) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1567436) audio_player: Buffer fill 3%, 1848 // 51200 bytes
I (1586206) audio_player: Buffer fill 3%, 1565 // 51200 bytes I (1605116) audio_player: Buffer fill 0%, 212 // 51200 bytes I (1624176) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1642966) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1661836) audio_player: Buffer fill 1%, 525 // 51200 bytes I (1680956) audio_player: Buffer fill 3%, 1648 // 51200 bytes I (1700126) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1718896) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1737656) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1756536) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1775276) audio_player: Buffer fill 2%, 1436 // 51200 bytes
I (1794436) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1813266) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1832026) audio_player: Buffer fill 1%, 971 // 51200 bytes I (1851166) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1869966) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1888766) audio_player: Buffer fill 3%, 1568 // 51200 bytes I (1907896) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1926666) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1945506) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1964276) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1983176) audio_player: Buffer fill 1%, 944 // 51200 bytes I (2002236) audio_player: Buffer fill 1%, 847 // 51200 bytes
I (2021006) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (2039846) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (2058616) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (2077706) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (2096606) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (2115346) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (2134506) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (2153306) audio_player: Buffer fill 3%, 1847 // 51200 bytes I (2172176) audio_player: Buffer fill 3%, 1647 // 51200 bytes I (2191266) audio_player: Buffer fill 1%, 674 // 51200 bytes I (2210066) audio_player: Buffer fill 2%, 1290 // 51200 bytes I (2228936) audio_player: Buffer fill 1%, 525 //
I (123187) wifi: state: run -> init (0) I (123187) wifi: pm stop, total sleep time: 49539628 us / 117292179 us
I (123187) wifi: new:<11,0>, old:<11,0>, ap:<255,255>, sta:<11,0>, prof:1 I (123207) wifi: flush txq I (123207) wifi: stop sw txq I (123207) wifi: lmac stop hw txq E (123207) main: Wifi Disconnected. ets Jun 8 2016 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0018,len:4 load:0x3fff001c,len:3580 load:0x40078000,len:9300 load:0x40080400,len:5764 entry 0x400806d4 E (573) spiram: SPI RAM enabled but initialization failed. Bailing out. I (137) main: starting app_main() I (137) main: RAM left: 200488 E (137) main: Running partition type 0 subtype 16 (offset 0x00010000) I (157) main: Partition init done... Log level is now ESP_LOG_INFO I (367) vs1053: VS1053 LFreq: 1403508 I (367) vs1053: VS1053 HFreq: 6153846 I (4267) vs1053: VS1053/VS1003 detected. MP3Status: 40, Version: 4 I (4267) vs1053: SCI_Status = 0x40 I (4267) vs1053: SCI_Mode (0x4800) = 0x4802 I (4267) vs1053: SCI_ClockF = 0xB800 I (4267) vs1053: VS Version (VS1053 is 4) = 4 I (4267) vs1053: I2S Speed: 0 I (4327) vs1053: volume: 42 I (4327) main: hardware initialized I (4327) main: Hardware init done... I (4347) main: LCD Type 192 I (4377) addonucg: lcd init type: 192, Rotat: 0 I (4427) ucg_hal: UCG_COM_MSG_POWER_UP: 80 ns so in Hz: 12500000 I (4427) ucg_hal: ... Adding spi lcd bus Speed= 25000000. I (4547) addonucg: lcd init Color type: 192 I (4607) addonucg: X: 160, yy: 128, y: 10
I (4617) main: audio_output_mode 4 One of I2S=0, I2S_MERUS, DAC_BUILT_IN, PDM, VS1053 I (4617) main: Set Song buffer to 50k I (4617) main: Set baudrate at 115200 I (4617) main: Release 1.9, Revision 0 I (4617) main: SDK v3.3-beta1-268-g5c88c5996-dirty I (4627) main: Heap size: 148068 I (4977) main: Volume set to 42 I (4987) main: t0 task: 3ffb1a30 I (5007) main: starting wifi I (5017) wifi: wifi driver task: 3ffbd8a4, prio:23, stack:3584, core=0 I (5017) wifi: wifi firmware version: 38e2484 I (5017) wifi: config NVS flash: enabled I (5017) wifi: config nano formating: disabled I (5027) wifi: Init dynamic tx buffer num: 32 I (5027) wifi: Init data frame dynamic rx buffer num: 32 I (5027) wifi: Init management frame dynamic rx buffer num: 32 I (5027) wifi: Init static tx buffer num: 16 I (5037) wifi: Init static rx buffer size: 1600 I (5037) wifi: Init static rx buffer num: 10 I (5047) wifi: Init dynamic rx buffer num: 32 WIFI TRYING TO CONNECT TO SSID 2 E (5047) wifi: esp_wifi_disconnect 964 wifi not start I (5067) main: connecting I (5127) wifi: mode : sta (3c:71:bf:8c:01:78) I (5137) main: Initialised wifi I (5257) wifi: new:<11,0>, old:<1,0>, ap:<255,255>, sta:<11,0>, prof:1 I (5927) wifi: state: init -> auth (b0) I (5937) wifi: state: auth -> assoc (0) I (5937) wifi: state: assoc -> run (10) I (5957) wifi: connected with HomeLan, channel 11, bssid = c8:0e:14:f3:c4:47 I (5967) wifi: pm start, type: 1
E (5967) event: invalid static ip I (5967) main: Wifi connected
DNS: 192.168.178.1 IP: 192.168.178.58
I (6857) main: mDNS Init ok E (6857) main: mDNS Hostname: karadio32 I (6867) renderer: chip revision 1 I (6887) renderer: i2s intr:0 I (7227) main: RAM left 78100 I (7227) main: uartInterfaceTask task: 3ffb8b50 I (7237) main: clientTask task: 3ffb8cc8 I (7247) servers: watermark: 0xaac 2732 I (7247) servers: telnetServer_sock socket: 52, errno: 0 I (7247) servers: Webserver socket: 53, errno: 0 I (7247) main: serversTask task: 3ffe6ed4 I (7257) main: task_addon task: 3ffe7e00 W (7327) GPIO: g_get_adc err 0x1102 I (7327) addon: rmt_nec_rx_task task: 3ffe8980 I (7327) addon: task_lcd task: 3ffe9384 I (7857) main: Init Done READY. Type help for a list of commands
autostart: playing:1, currentstation:5
I (9687) webserver: playstationInt: 5, g_device: 5 I (10237) webclient: Webclient socket: 55, errno: 0
I (11537) webclient: watermark : 3b4 948 I (11537) webclient: Webclient socket: 57, errno: 0
karawin
commented
5 years ago Every things are normal seen from the log.
You need to cut the local echo to avoid #INFO:" lines. and #INFO:"#INFO:" etc. (never ends)
The station or the wifi stream is very low. I (1794436) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (1813266) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (1832026) audio_player: Buffer fill 1%, 971 // 51200 bytes I (1851166) audio_player: Buffer fill 2%, 1436 // 51200 bytes .... Is abnormal.
Hans-JR
commented
5 years ago OK, I double checked the buffer fill rate. With the patch loaded it is always between 2 and 4%, without the patch it is 90 to 94%. I checked it with various stations. I remember, that there was a necessary hardware modification required to the decoder board (short pins 33 and 34). Is this still necessary?
Is there any way to reload the previous release (i.e. 1.7..)?
From: KaraWin [mailto:notifications@github.com] Sent: Tuesday, February 19, 2019 9:45 PM To: karawin/Ka-Radio32 Ka-Radio32@noreply.github.com Cc: Elbskipper hans@richter-dollern.de; Author author@noreply.github.com Subject: Re: [karawin/Ka-Radio32] Release 1.9R0, Problem with VS1053 (#96)
Every things are normal seen from the log.
karawin
commented
5 years ago I remember, that there was a necessary hardware modification required to the decoder board (short pins 33 and 34). Is this still necessary? No it was a fake news because in KaRadio a patch is included to avoid it.
The vs1053 patch cannot explain your problem. It seems related to the echo in the serial. The cpu is filled by the serial read. A kind of larsen.
Hans-JR
commented
5 years ago Here is a link with the description of the issue people had some time ago:
http://www.bajdi.com/lcsoft-vs1053-mp3-module/ http://www.bajdi.com/lcsoft-vs1053-mp3-module/
But I do not think, that this is my issue.
Here is a new logfile with patch. No more echo’s, but still no sound.
I (194747) wifi: state: run -> init (0) I (194747) wifi: pm stop, total sleep time: 89818224 us / 188996938 us
I (194747) wifi: new:<11,0>, old:<11,0>, ap:<255,255>, sta:<11,0>, prof:1 I (194767) wifi: flush txq I (194767) wifi: stop sw txq I (194767) wifi: lmac stop hw txq E (194767) main: Wifi Disconnected. ets Jun 8 2016 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0018,len:4 load:0x3fff001c,len:3580 load:0x40078000,len:9300 load:0x40080400,len:5764 entry 0x400806d4 E (573) spiram: SPI RAM enabled but initialization failed. Bailing out. I (137) main: starting app_main() I (137) main: RAM left: 200488 E (137) main: Running partition type 0 subtype 16 (offset 0x00010000) I (157) main: Partition init done... Log level is now ESP_LOG_INFO I (367) vs1053: VS1053 LFreq: 1403508 I (367) vs1053: VS1053 HFreq: 6153846 I (4267) vs1053: VS1053/VS1003 detected. MP3Status: 40, Version: 4 I (4267) vs1053: SCI_Status = 0x40 I (4267) vs1053: SCI_Mode (0x4800) = 0x4802 I (4267) vs1053: SCI_ClockF = 0xB800 I (4267) vs1053: VS Version (VS1053 is 4) = 4 I (4267) vs1053: I2S Speed: 0 I (4277) VS1053 Patches: plugin size 8896 4448 I (4277) VS1053 Patches: plugin start: 7 1 8050 6
I (4617) vs1053: volume: 35 I (4617) main: hardware initialized I (4617) main: Hardware init done... I (4637) main: LCD Type 192 I (4667) addonucg: lcd init type: 192, Rotat: 0 I (4717) ucg_hal: UCG_COM_MSG_POWER_UP: 80 ns so in Hz: 12500000 I (4717) ucg_hal: ... Adding spi lcd bus Speed= 25000000. I (4837) addonucg: lcd init Color type: 192 I (4897) addonucg: X: 160, yy: 128, y: 10
I (4907) main: audio_output_mode 4 One of I2S=0, I2S_MERUS, DAC_BUILT_IN, PDM, VS1053 I (4907) main: Set Song buffer to 50k I (4907) main: Set baudrate at 115200 I (4907) main: Release 1.9, Revision 0 I (4907) main: SDK v3.3-beta1-268-g5c88c5996-dirty I (4917) main: Heap size: 139020 I (5267) main: Volume set to 35 I (5297) main: t0 task: 3ffb1a88 I (5297) main: starting wifi I (5307) wifi: wifi driver task: 3ffbd558, prio:23, stack:3584, core=0 I (5307) wifi: wifi firmware version: 38e2484 I (5307) wifi: config NVS flash: enabled I (5307) wifi: config nano formating: disabled I (5327) wifi: Init dynamic tx buffer num: 32 I (5327) wifi: Init data frame dynamic rx buffer num: 32 I (5327) wifi: Init management frame dynamic rx buffer num: 32 I (5327) wifi: Init static tx buffer num: 16 I (5337) wifi: Init static rx buffer size: 1600 I (5337) wifi: Init static rx buffer num: 10 I (5337) wifi: Init dynamic rx buffer num: 32 WIFI TRYING TO CONNECT TO SSID 2 E (5347) wifi: esp_wifi_disconnect 964 wifi not start I (5367) main: connecting I (5427) wifi: mode : sta (3c:71:bf:8c:01:78) I (5427) main: Initialised wifi I (5557) wifi: new:<11,0>, old:<1,0>, ap:<255,255>, sta:<11,0>, prof:1 I (6227) wifi: state: init -> auth (b0) I (6237) wifi: state: auth -> assoc (0) I (6237) wifi: state: assoc -> run (10) I (6257) wifi: connected with HomeLan, channel 11, bssid = c8:0e:14:f3:c4:47 I (6257) wifi: pm start, type: 1
E (6257) event: invalid static ip I (6257) main: Wifi connected
DNS: 192.168.178.1 IP: 192.168.178.58
I (7147) main: mDNS Init ok E (7147) main: mDNS Hostname: karadio32 I (7147) renderer: chip revision 1 I (7177) renderer: i2s intr:0 I (7517) main: RAM left 69184 I (7517) main: uartInterfaceTask task: 3ffb8b50 I (7527) main: clientTask task: 3ffb8cc8 I (7537) servers: watermark: 0xab8 2744 I (7537) servers: telnetServer_sock socket: 52, errno: 0 I (7537) servers: Webserver socket: 53, errno: 0 I (7537) main: serversTask task: 3ffe91a8 I (7547) main: task_addon task: 3ffea0c4 W (7667) GPIO: g_get_adc err 0x1102 I (7667) addon: rmt_nec_rx_task task: 3ffeac44 I (7667) addon: task_lcd task: 3ffeb648 I (8147) main: Init Done READY. Type help for a list of commands
autostart: playing:1, currentstation:10
I (9997) webserver: playstationInt: 10, g_device: 10 I (10527) webclient: Webclient socket: 56, errno: 0
I (19487) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (36657) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (55557) audio_player: Buffer fill 2%, 1149 // 51200 bytes I (74657) audio_player: Buffer fill 3%, 1848 // 51200 bytes
I (93357) audio_player: Buffer fill 3%, 1847 // 51200 bytes I (112287) audio_player: Buffer fill 1%, 527 // 51200 bytes I (131347) audio_player: Buffer fill 2%, 1435 // 51200 bytes I (150117) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (168987) audio_player: Buffer fill 3%, 1648 // 51200 bytes I (188077) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (206907) audio_player: Buffer fill 1%, 526 // 51200 bytes I (226067) audio_player: Buffer fill 3%, 1848 // 51200 bytes
I (245657) audio_player: Buffer fill 3%, 1847 // 51200 bytes I (264397) audio_player: Buffer fill 2%, 1029 // 51200 bytes I (283237) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (301977) audio_player: Buffer fill 3%, 1848 // 51200 bytes I (320747) audio_player: Buffer fill 2%, 1436 // 51200 bytes I (339937) audio_player: Buffer fill 3%, 1848 // 51200 bytes
From: KaraWin [mailto:notifications@github.com] Sent: Wednesday, February 20, 2019 10:32 AM To: karawin/Ka-Radio32 Ka-Radio32@noreply.github.com Cc: Elbskipper hans@richter-dollern.de; Author author@noreply.github.com Subject: Re: [karawin/Ka-Radio32] Release 1.9R0, Problem with VS1053 (#96)
I remember, that there was a necessary hardware modification required to the decoder board (short pins 33 and 34). Is this still necessary? No it was a fake news because in KaRadio a patch is included to avoid it. The vs1053 patch cannot explain your problem. It seems related to the echo in the serial. The cpu is fulled by the serial read. A kind of larsen. — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/karawin/Ka-Radio32/issues/96#issuecomment-465496381 , or mute the thread https://github.com/notifications/unsubscribe-auth/AkLGsTEstzl8idiaolTRAZYCXaZkMhm6ks5vPRX7gaJpZM4a_qoZ .
karawin
commented
5 years ago Can't see any reason for not receiving the stream with or without patch. The only reason i can imagine is a bad DREQ request (permanent level 1) that read permanently the audio buffer. The patch is from vlsi, so i cannot check it. http://www.vlsi.fi/fileadmin/software/VS10XX/vs1053b-patches.pdf But hundred of users use it.
Please check the DREQ wire. Or may be a crash of the vs1053 itself?
Hans-JR
commented
5 years ago I checked the wiring. It looks OK. I just wonder, why it worked until the last OTA. Anyway, I can live without the patch.
Thanks for your support.
karawin
commented
5 years ago I think that it is a vs1053 crash. From 1.5 or 1.6, the patch is the new one. May be a consequence? But never heard about problem before. May be a power supply a bit weak or a fake vs1053? Bye
Hans-JR
commented
5 years ago Sorry, it's me again….. I am really interested in why I do have this issue. So I installed the vs1053 to my MCU8255 board. I loaded Software Version V1.7R1. Next I updated to V1.8R2. With both versions it worked fine with the patch loaded. Next I connected the vs1053 back to the ESP32 board. Then I loaded Software Version V1.5R2. With this Version it workes fine with the patch loaded.
Here is the log file: `
VS1053 Patch will be Loaded after power Off and On#
I (50351) wifi: state: run -> init (0) I (50361) wifi: pm stop, total sleep time: 23120797 us / 44051042 us
I (50361) wifi: n:11 0, o:11 0, ap:255 255, sta:11 0, prof:1 I (50381) wifi: flush txq I (50381) wifi: stop sw txq I (50381) wifi: lmac stop hw txq E (50381) main: Wifi Disconnected. Connection tried again E (50381) main: Wifi Disconnected. reboot ets Jun 8 2016 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0018,len:4 load:0x3fff001c,len:3580 load:0x40078000,len:9300 load:0x40080400,len:5764 entry 0x400806d4 E (130) esp_core_dump: No core dump partition found! I (132) main: starting app_main() I (132) main: RAM left: 159656 E (132) main: Running partition type 0 subtype 16 (offset 0x00010000) I (172) main: Partition init done... Log level is now ESP_LOG_INFO E (4212) vs1053: VS1053/VS1003 detected. MP3Status: 40, Version: 4 I (4212) vs1053: SCI_Status = 0x40 I (4212) vs1053: SCI_Mode (0x4800) = 0x4802 I (4212) vs1053: SCI_ClockF = 0xB800 I (4212) vs1053: VS Version (VS1053 is 4) = 4 device: 3ffcd380 I2S Speed: 0 I (4222) VS1053 Patches: plugin size 6350 3175 I (4222) VS1053 Patches: plugin start: 7 1 8050 6
I (4442) VS1053 Patches: plugin size 234 117 I (4442) VS1053 Patches: plugin start: 7 1 8f00 6
volume: 35 I (4542) main: hardware initialized I (4542) main: Hardware init done... E (4542) main: LCD Type 192 I (4542) addonucg: lcd init type: 192 I (4632) ucg_hal: UCG_COM_MSG_POWER_UP: 100 ns so in Hz: 10000000 I (4632) ucg_hal: ... Adding device bus Speed= 20000000. I (4702) addonucg: lcd init Color type: 192 X: 160, yy: 128, y: 14 I (4832) main: audio_output_mode 4 One of I2S=0, I2S_MERUS, DAC_BUILT_IN, PDM, VS1053 I (4832) main: Set baudrate at 115200 I (4832) main: Release 1.5, Revision 2 I (4832) main: SDK v3.3-dev-236-gfa59b1b1c-dirty I (4832) main: Heap size: 152272 I (5172) main: Volume set to 35 I (5172) main: t0 task: 3ffcd814 I (5172) main: starting wifi I (5182) wifi: wifi driver task: 3ffd71bc, prio:23, stack:3584, core=0 I (5182) wifi: wifi firmware version: abbd416 I (5182) wifi: config NVS flash: enabled I (5192) wifi: config nano formating: disabled I (5212) wifi: Init dynamic tx buffer num: 32 I (5212) wifi: Init data frame dynamic rx buffer num: 32 I (5212) wifi: Init management frame dynamic rx buffer num: 32 I (5222) wifi: Init static tx buffer num: 16 I (5222) wifi: Init static rx buffer size: 1600 I (5222) wifi: Init static rx buffer num: 10 I (5232) wifi: Init dynamic rx buffer num: 32 WIFI TRYING TO CONNECT TO SSID 2 E (5232) wifi: esp_wifi_disconnect 955 wifi not start I (5262) main: connecting I (5332) wifi: mode : sta (3c:71:bf:8c:01:78) I (5332) main: Initialised wifi I (5452) wifi: n:11 0, o:1 0, ap:255 255, sta:11 0, prof:1 I (6462) wifi: state: init -> auth (b0) I (6462) wifi: state: auth -> assoc (0) I (6472) wifi: state: assoc -> run (10) I (6482) wifi: connected with HomeLan, channel 11 I (6532) wifi: pm start, type: 1
E (6532) event: invalid static ip E (6532) main: Wifi connected
DNS: 192.168.178.1 IP: 192.168.178.58
I (7292) main: mDNS Init ok I (7302) renderer: chip revision 1 I (7352) renderer: i2s intr:0 I (7862) main: RAM left 69560 I (7862) main: uartInterfaceTask task: 3ffe79f8 I (7862) main: clientTask task: 3ffe871c I (7862) servers: watermark: 0xa4c 2636 I (7862) servers: telnetServer_sock socket: 54, errno: 0 I (7862) servers: Webserver socket: 55, errno: 0 I (7872) main: serversTask task: 3ffe9440 I (7872) main: task_addon task: 3ffeab48 Init ..I (8072) addon: event_ir: 3ffeae28 I (8072) addon: event_lcd: 3ffeacb0 I (8082) addon: rmt_nec_rx_task task: 0 I (8082) addon: task_lcd task: 3ffec128 ........ Done READY. Type help for a list of commands autostart: playing:1, currentstation:5
I (10562) webserver: playstationInt: 5, device: 5 I (10862) webclient: Webclient socket: 57, errno: 0
I (12022) webclient: watermark : 3bc 956 I (12022) webclient: Webclient socket: 58, errno: 0
` Next I updated to the latest version via telnet "sys.update". After that it failed again. Then I went back to the V1.5R2 and it works again. So there is defenetly something different between these versions. Do you have any further recommandations in order to track this issue down?
karawin
commented
5 years ago The vlsi patch is the difference. Your vs crashs
Hans-JR
commented
5 years ago OK. Which release is the latest one with the old patch? Is there a way to use the latest update but keep (or reload) the previous patch?
karawin
commented
5 years ago V1.6 R3
Hans-JR
commented
5 years ago yep, it works in V1.6R3 with the patch loaded. Interesting is, that the Buffer fill rate with the old patch is between 90 and 99% compared to 1 to 3% with the new patch.
karawin
commented
5 years ago It is because the vs1053 crashed with dreq line activated so the buffer is read at the speed maximum. because the vs1053 seems to ask for data permanently. If the vs1053 crash, the probable cause is a fake 1053b. I don't think to go back to the old patch. Sorry.
Hans-JR
commented
5 years ago I didn't expect you to go back.
I will at a later time order another one. Although this one Looks exactly like the one you recommended.
Please consider this issue as closed.
Thank you!!!
karawin
commented
5 years ago 
pilnikov
commented
5 years ago red boards are better
karawin
commented
5 years ago Alientek are better but production ended.
Hans-JR
commented
5 years ago Update: I finally received the new board. This time I ordered the "red" one. With this board it works fine. The Buffer fill rate is now at 92-98%. I have no idea whats wrong with the "blue" board. I did check the DREQ connection on the board from the connector to the pin of the IC. It looks ok. Regards
Hans p.s. the release V1.6 R4 worked as well with the "blue" board
Update2: I compared the two boards and noticed, that pin 34 on the "blue" board has no connection while pin 33 has a pull up resistor (the "red" board has a pull up on both pins). So I connected pins 33 and 34 together and it works! This issue is explained in the "vsdsp-forum".
HI, since I did an OTA update to 1.9R0 there is no sound anymore via the VS1053 board. If I unload the patch (sys.patch("0") it is ok. If I load it again it fails again. In the past I always used the patch. My config: VS1053, Rotary Encoder, LCD_SPI_ST7735 No customized config file