keirf / flashfloppy

Floppy drive emulator for Gotek hardware
Other
1.37k stars 198 forks source link

Info: FF with 26-pin header Gotek Floppy #155

Closed JoanMCD closed 6 years ago

JoanMCD commented 6 years ago

I sucessful use FF with an 26-pin header Gotek Floppy and use it in my Tektronix TDS3000 series (TDS3012B) Oscilloscope. The PB and the LEDs are at the same pins. I have to remove the resistors RA & RC (normaly 0R), and (not sure if it's nessesary) I also removed RB and the external EEPROM (8pin SOC). The PCB No. of the GOtek is SFRC2D. Model: Slim drive - SFR1M44-DU26 GOTEK.

Thx for the great project!

keirf commented 6 years ago

Do you know what RA, RB, RC (all 0R?) do or how they are connected into the Gotek schematic, and why you had to remove them? If I can document that I can add something to the "Gotek Compatibility" section of the wiki.

JoanMCD commented 6 years ago

Yes, all are assembled with 0R. With RA the drive ever shows 'Upd' on the display. The drive is mounted now, I can't measure the Rx->pin config. But I have a fast drawing on paper - maybe I can re-read it from there.

From here we can know that RA is pulling down Pin 37 of the STM32 Over all, the info is that by removing the resistors the 26-pin drive is also usable.

keirf commented 6 years ago

Added a link to this ticket to the wiki.

JoanMCD commented 6 years ago

pcb

stm32f105

presslab-us commented 5 years ago

Thanks for the info, I was able to get the SFR1M44-DU26 working on my LeCroy LC684 oscilloscope. I only removed the three resistors and left the EEPROM.

mbirth commented 5 years ago

Did it not work before? I have the SFR1M44-DU26 happily working in my TDS784D without any modifications. Just curious as to why you guys modded your disk emus.

oldtrusty commented 4 years ago

I also have the SFR1M44-DU26 26 pin version and having trouble getting the oscope to recognize my USB stick. Currently have the RA, RB, & RC 0R resistors removed. Only jumper in use is the S1 jumper on the rear header. I have successfully upgraded the firmware to FF and tried v3.9a and 2.13 with the same results. My scope constantly gives me a message to insert floppy disk, which leads me to believe that my USB stick is not properly formatted. You can see in the pic that my oscope finds the drive ok and lists the directory screen. It just won't read my files (previous oscope screen captures while using the floppy drive) that I placed on the disk for testing. I have tried a 1Gb and 2Gb stick formatted into (99) 1.4Mb disks. Looking for some assistance in how others who successfully got this working and how you all prepared your USB drives and what image settings you used. To this point I have tried every option in FF.CFG (placed in the root directory) with no success. Also tried removing serial eprom - no difference. The USB drive does however increment/decrement the virtual floppy disks when I press the front up/down buttons. I can see the LED inside of the USB drive and the ones on the emulator give feedback when I try to access the drive. So it seems to be somewhat working. See attached photos. Any help on this would be greatly appreciated. 20191231_141009 20191231_141345 20191231_141446 20191231_142724

mbirth commented 4 years ago

IMHO the original firmware of the SFR1M44-DU26 works better. With no USB device connected, it uses the internal flash memory as a virtual disk. Once you've connected a USB device (one large partition formatted to FAT32) and press the right button, it'll then read the first few files (up to 1.44 MB) from the USB and present those as the "disk". Pressing the button again will read the next few files and so on.

And if you want to store files on USB, just press the left button and from that moment on, all files written to the "disk" will end up on the USB drive. No need to make multiple disk images or special partitions or anything.

JoanMCD commented 4 years ago

The Tektronix TDS3000 series have a 26pin flat wire, so to use the SFR1M44-DU26 is a logic step. The original FW offers only a non HD Disk - what was not accepted by (my) TDS, so to replace the FW to get a HD drive was the next logical step.

JoanMCD commented 4 years ago

@oldtrusty I see a lot of markings on your PCB, and also a TO92 Transistor - ... As i remember, at the end I didn't need such modifications.

oldtrusty commented 4 years ago

@mbirth do you have the original firmware or know of a link to it?

oldtrusty commented 4 years ago

@JoanMCD the markings were to help me identify the boot0, +3.3, Tx, Rx, and Gnd pin during programming of FF. The TO92 (2N2222A) is temporary and was to replace the 1P SOT23 (2N2222A), which I damaged when I was playing with the rear jumpers. It tells the uC that the disk is read-only, I believe. That's the constant error I was getting when it was damaged. When I replaced the error went away.

How did you format your USB drive and did you have to load any of the .img files mentioned in the FF examples?

mbirth commented 4 years ago

@oldtrusty Sorry, no. Never fiddled with my Gotek and/or dumped the fw.

kkwannyc commented 4 years ago

Hi - fellow Flashfloppy user here with the SFR1M44-DU26. Mine was used with an IBM slimline floppy drive enclosure (formerly occupied by a TEAC FD05HF) to allow oldschool ThinkPads (560E) to work off disk images and whatnot. Mine has a revised logic board variant (SFRC2DA) that looks to be almost the same as the SFRC2D.

DIsk on Gotek

Just to confirm with the postings of @JoanMCD - you do have to remove/disconnect resistors RA and RC for the device to get out of flash update mode. Once it's removed the device will work just fine. Retaining the RB+EEPROM (used by the original firmware to...I don't even know what it does as this Gotek variant does not behave like normal Goteks, so formatting your drive into multiple segments of 1.44MB in size is not going to work)...is purely up to you. I disconnected RB but kept the EEPROM alone on mine.

Things to be aware of -

[Boot0] [3.3] [TX] [RX] [RST] [5v] [GND]

The following pins on the output corresponds to the following pinout on the STM32F105 LQFP64 package, and with the colors noted on the diagram below.

5v - Pin1 (VBAT) Red Boot0 - Pin 60 (Boot0), Purple TX - Pin 42 (J? next to J4, PA09), Green RX - Pin 43 (J4, PA10), Blue

There is an AMS1117 voltage regulator(SOT223 package) with 3 pins, denoted on the board as U4. Left is GND, middle is 3.3v, and right is 5v.

On the SFRC2D/A the display connector is the following from left to right:

[SDA] [SCL] [GND] [3.3V]
SCL - PIn 29 (PB10) - Yellow SDA - Pin 30 (PB11) - Orange

Ground is denoted as Black, and 3.3v is denoted as Orange-Red.

To program the SFRC2D/A with a USB-TTL serial adapter (preferably one that can do both 3.3/5v with the flick of a jumper), put a jumper between Boot0 and 3.3v, TX and TX to the correct pins, run VCC to the 5v pin (below J4), and ground to the GND pin (below RST), and follow the usual instructions.

There are existing test points on the board that can be used to verify that the soldering has been done correctly. See the attached photo for an idea of where they are located. Test points for RX/TX is above the STM105, Boot0 is to the left of the STM32F105, SDA/SCL is to the right (SDA will require you to test continuity with pin 27 directly), and 5v is present in at least 4 locations + the right leg off U4. 3.3v is supposed to be on the rightmost pin of the display pinout and on the middle leg off U4. @keirf you might find this photo of the SFRC2DA useful:

SFRC2DA-Annotated

Hope this bit is useful for those trying to make this device do useful things - the SFR1M44-GU26 have practically no open documentation available whatsoever besides "buy this overpriced Gotek variant" and a poorly translated instruction manual of questionable applicability. @mbirth The default firmware is utterly useless crap if you plan to work with non-standard disk images, like the 1.72MB XDF images used by IBM's OS/2. For 1.44MB floppies it's not that difficult to grab a disk image template and have the FDC write/save it to a blank disk image, save it and then rename it on the USB stick later.

@oldtrusty did your model come with the jumpers for the bottom headers? I noticed that on mine the JD/JE headers were jumped...not sure if this might impact your Oscilloscope reading the device.

ledge64 commented 3 years ago

Hello. I am currently having some trouble with programming the SFRC2DA with the USB-TTL serial adapter. I followed the instructions given by @kkwannyc

To program the SFRC2D/A with a USB-TTL serial adapter (preferably one that can do both 3.3/5v with the flick of a jumper), put a jumper between Boot0 and 3.3v, TX and TX to the correct pins, run VCC to the 5v pin (below J4), and ground to the GND pin (below RST), and follow the usual instructions.

unnamed (11)

I removed the three resistors (RB, RC, and RA), then I followed the wiring diagram. I attached a picture of how I wired the SFRC2DA to the USB-TTL serial adapter. I then proceeded to follow the video from Kris Cochrane that was linked in the wiki page. After opening the ST Flasher program I got the following error attached.

Screenshot 2020-12-22 161946

I was wondering what else I could be missing.

Thanks

dchauran commented 3 years ago

Just to add a success here:

Tektronix TDS640A Board rev SFRC2DA 0.91" oled Removed RA, RB, RC, left the eeprom. Attached a microswitch in place of RA, as the pins correspond to JA and I wanted that third button, mounted by soldering it to the side of an existing button. My board came with JD and JE installed, I had to remove those. Shugart mode, not IBM as I have seen on other scopes.

Initial programming was performed in DFU/USB mode (jump 3.3v/boot and tx/5v, connect to PC and use the ) since I couldn't find my USB to serial adapter, worked perfectly.

The drive is a bit narrower than the original drive, so there is a small gap in the front panel.

The drive seems slow, as it takes about 10 seconds to write 38KB, or around 30kbit/second, but I didn't think to time how long it took on an actual floppy drive.

IMG_20210511_170714

kkwannyc commented 3 years ago

Hello. I am currently having some trouble with programming the SFRC2DA with the USB-TTL serial adapter. I followed the instructions given by @kkwannyc

To program the SFRC2D/A with a USB-TTL serial adapter (preferably one that can do both 3.3/5v with the flick of a jumper), put a jumper between Boot0 and 3.3v, TX and TX to the correct pins, run VCC to the 5v pin (below J4), and ground to the GND pin (below RST), and follow the usual instructions.

unnamed (11)

I removed the three resistors (RB, RC, and RA), then I followed the wiring diagram. I attached a picture of how I wired the SFRC2DA to the USB-TTL serial adapter. I then proceeded to follow the video from Kris Cochrane that was linked in the wiki page. After opening the ST Flasher program I got the following error attached.

Screenshot 2020-12-22 161946

I was wondering what else I could be missing.

Thanks

Check continuity with the test points/ pins I’ve given and see if there are some cold solders/bad contacts somewhere (it happens sometimes). Also, I think you need to unlock the device for write before it will work, but if the commands are downright being ignored it might be a communications issue (hence…continuity checks)

pdieng commented 3 years ago

Just to add a success here:

Tektronix TDS640A Board rev SFRC2DA 0.91" oled Removed RA, RB, RC, left the eeprom. Attached a microswitch in place of RA, as the pins correspond to JA and I wanted that third button, mounted by soldering it to the side of an existing button. My board came with JD and JE installed, I had to remove those. Shugart mode, not IBM as I have seen on other scopes.

Initial programming was performed in DFU/USB mode (jump 3.3v/boot and tx/5v, connect to PC and use the ) since I couldn't find my USB to serial adapter, worked perfectly.

The drive is a bit narrower than the original drive, so there is a small gap in the front panel.

The drive seems slow, as it takes about 10 seconds to write 38KB, or around 30kbit/second, but I didn't think to time how long it took on an actual floppy drive.

IMG_20210511_170714

I have a TDS640A and I am trying to do the exact same thing as you. I have Flash Floppy firmware on my SFRC2DA and removed RA, RB and RC. However when ever I try to plug in a thumb drive, it gives me error 34. I have a freshly formatted thumbdrive with just FF.CFG and IMG.CFG. When I plug it in it also creates the empty IMAGE_A.CFG file.

What do you have on your thumbdrive? Do you have any jumpers installed?

It might be because I don't have a working thumbdrive setup yet but also when I press the "Hard Copy" button on the scope, it tells me that the "File System Media is Missing".

andrewpono commented 3 years ago

Another success story (TDS3032B) - just added a quick guide based on this thread and other sources: https://github.com/andrewpono/TDS3000-Series-Gotek-FlashFloppy

hara3d commented 3 years ago

Thanks, I also success Lecroy LC574ALS (FDD was Citizen W1D) Gotek SFR1M44-DU26 / SFRC2D.B(Artery AT32F415RBT7) OLED(0.91) FlashFloppy v3.29(Native mode) S1 short

With only RA removed, lecroy didn't seem to recognize the replacement, even if I changed discs (.img) with left and right buttons. With RA, RB, and RC removed, reloading directry can be selected after changed discs. So if we use only one disk image, it seems good to remove only RA.

coredump4 commented 2 years ago

Thanks to all for this informative thread, it really helped me. One tidbit I'll add is, if you're having trouble getting a Gotek (slim or regular) into DFU mode, try a different USB cable. I had been trying to use a modern, good-quality USB3 A-A cable that did not work, but an older USB2 cable did. HTH.

hisink commented 2 years ago

Another success on TDS3032. Some road blocks, but eventually all solved. Here are the brief procedures.

  1. connect the du26 to pc with boot0 pin short to the next hole for dfu load.
  2. install Artery driver. (difficult to find. especially after they change domain name.) I use the version 1.5.47
  3. flash the FF version 3.30 with Artery dfu software.
  4. remove ra/rb/rc, install LED and remove JD,JE.
  5. cut the plastic at the end of the gotek enclosure. the one I bought is about 3mm longer than the original floppy drive. so it can't fit into the chassis. After shortening it, then install it back to the oscilloscope
  6. put the usb drive, format to fat32, and copy in an image. the everything just work.
pbernicchi commented 2 years ago

@kkwannyc I've pored through your writeup and tried to glean from your pics here and on VOGONS what your jumper setup might be... e.g., you have JE/JD/S1 jumped in your picture above but I can't tell from the pics on VOGONS because the Gotek is closed up.

I'm trying like hell to get the same Artery DU26 working on my ThinkPad 560 AND 570. I'm getting a green LED during POST but "Operating System not found" on known, good images.

Would you mind attaching your FF.CFG as well so perhaps we can tag this for (specifically) early ThinkPads with the 26-pin external connector?

Wierzbowsky commented 2 years ago

Another success on TDS3032. Some road blocks, but eventually all solved. Here are the brief procedures.

  1. remove ra/rb/rc, install LED and remove JD,JE.

@hisink Thanks for the clear instructions. Is there a need to put back RA/RB/RC and any of the jumpers after reprogramming?

keirf commented 2 years ago

They correspond to jumpers JA JB JC on normal Goteks. No need to reinstall those resistors.

Wierzbowsky commented 2 years ago

They correspond to jumpers JA JB JC on normal Goteks. No need to reinstall those resistors.

So, only S0 or S1 jumper should remain? I want to make a combo - this slim Gotek + slim floppy drive and put it into the normal 3.5 FDD drive's compartment of my Arabic MSX. I've already designed the board to connect 2 slim drives to a normal 34-pin FDD cable.

keirf commented 2 years ago

I think so. If JC is actually correct you can get same effect with interface=ibmpc in FF.CFG. But I think shugart is probably correct.

Wierzbowsky commented 2 years ago

Thanks, I will test once I get my hands on the device.

Wierzbowsky commented 2 years ago

Removed 3 solder jumpers, 2 physical jumpers and flashed the device with FlashFloppy 3.34 firmware. Works like a charm in my Dual-Slim setup. Many thanks for your excellent work, @keirf!!

DualSlim

Wierzbowsky commented 2 years ago

I've created an article with links to the repositories. https://www.msx.org/forum/msx-talk/hardware/how-to-double-the-amount-of-floppy-drives-dualslim-comes-to-help

Olas-Audio commented 2 years ago

Hi everyone. A few years ago, I got an Agilent 54622A oscilloscope for about 100 USD, a real bargain and the truth is that it is an excellent measurement equipment, despite being just 100 MHz. I just want to share the methodology that I followed to be able to use a Gotek floppy emulator. Without having read this issue, I decided to buy the cheapest emulator of this brand (34 USD shipping included), it’s an SFR1M44-DU26 SFRC2D.B version. So, there is no need to buy an expensive type to perform this operation.

Step 1. Download FlashFloppy version 3.29 (I think 3.3 could also be used). https://github.com/keirf/FlashFloppy/wiki/Downloads

Step 2. Download the file Artery_ISP_Programmer_V1.5.46 or later and install the driver “Artery_DFU_DriverInstall.exe”. https://www.arterytek.com/en/product/AT32F415.jsp#Resource https://www.arterytek.com/download/TOOL/Artery_ISP_Programmer_V2.0.06.zip

Artery_ISP_Programmer_V1.5.46.zip

Step 3. Prepare the PCB for flashing according to the follow images:

image This version uses the Artery microcontroller.

image SFRC2D.B version.

image I used a USB type A cable on one end and on the other side I exposed the wires so I could solder them to the PCB. I performed this step since I didn't have a USB A-A type cable.

image I soldered the wires in the shown sequence to the base of the USB connector on the PCB, the layout is as follows: |GND-black|D+ Green|D- White|+V-Red|

193429704-be276406-6800-43d2-a941-f8445da027aa I soldered a 5-pin header to put a jumper between Boot-3V pins. I only left the S1 jumper in place.

193430053-a257c380-4e53-4fcb-a5bc-6b86b84f5d8f Install the driver.

image Then run the app “ArteryISSProgrammer.exe”.

image Select USB DFU as the port type. Then we proceed to connect USB cable.

image Select language and click next

image Click next

image Click next

image You must select Enable/disable protection, click yes from the dialog box and then click next

image Wait until it’s done then click back

image Click "Download to device" and then click the "add" button.

image Look for the Hex file of the version you want to install, in my case 3.29.

image Select "Global erase" and "verify after download" then click next

image

image

Finally click close. You can unplug the USB cable from the computer.

Now you can desolder the resistors RA, RB and RC and the USB cable in any case. The memory IC does not need to be preserved. I removed it so I could use it in some other project later on.

image

193429946-01c33a11-35b9-4eab-90b7-dee5d269b9e8

Don't forget to remove Jumper Boot-3.3V.

Finally, it is necessary to prepare you USB device. Give it a format FAT32 and then you need to copy the "1m44_fat12.img" file into the main directory of the USB that you just formatted. https://github.com/andrewpono/TDS3000-Series-Gotek-FlashFloppy/blob/main/1m44_fat12.img

That’s it, your scope should be ready to save Images into your USB stick. The file storing time it’s slow but it’s definitely more convenient than to use a Floppy Disk.

Cheers and enjoy your measurement!

kkwannyc commented 1 year ago

@kkwannyc I've pored through your writeup and tried to glean from your pics here and on VOGONS what your jumper setup might be... e.g., you have JE/JD/S1 jumped in your picture above but I can't tell from the pics on VOGONS because the Gotek is closed up.

I'm trying like hell to get the same Artery DU26 working on my ThinkPad 560 AND 570. I'm getting a green LED during POST but "Operating System not found" on known, good images.

Would you mind attaching your FF.CFG as well so perhaps we can tag this for (specifically) early ThinkPads with the 26-pin external connector?

Hah, sorry - I really need to log into my personal Github more often. JD/JE/S1 are indeed jumped on the Gotek. I haven't actually used it in the past few months since the OLED display on my custom enclosure just kept dying, and I only use it on my ThinkPad 560E (I am not sure where the cable for my 240 went...)

The Gotek (with an STM32) only have the following on its ff.cfg:

interface = ibmpc host = pc-dos pin02 = auto pin34 = auto write-protect = no max-cyl = 255 side-select-glitch-filter = 0 track-change = instant write-drain = instant index-suppression = yes head-settle-ms = 12 motor-delay = ignore chgrst = step ejected-on-startup = yes image-on-startup = last display-probe-ms = 3000 autoselect-file-secs = 1 autoselect-folder-secs = 2 folder-sort = always sort-priority = folders nav-loop = yes twobutton-action = zero display-type = oled-128x32 oled-font = 6x13 oled-contrast = 145

image

KingDaveRa commented 1 year ago

Hi all,

Just wanted to add my tuppence worth.

I've got the SFRC20.B and have successfully re-flashed it and got it working with a Toshiba T1900C laptop - they are very fussy as they use a slightly odd Citizen floppy drive (which has an unobtainium drive belt) and uses RDY on pin 34.

I did the following:

  1. Added pin headers as normal. Flashed using the standard methods.
  2. Removed RA resistor
  3. Jumpers as default

Relevant config in the FF.CFG:

interface = ibmpc
host = unspecified
pin02 = auto
pin34 = rdy

And that was it, booted fine. I hope this helps somebody else!

csulaguy commented 1 year ago

Hi - fellow Flashfloppy user here with the SFR1M44-DU26. Mine was used with an IBM slimline floppy drive enclosure (formerly occupied by a TEAC FD05HF) to allow oldschool ThinkPads (560E) to work off disk images and whatnot. Mine has a revised logic board variant (SFRC2DA) that looks to be almost the same as the SFRC2D.

DIsk on Gotek

Just to confirm with the postings of @JoanMCD - you do have to remove/disconnect resistors RA and RC for the device to get out of flash update mode. Once it's removed the device will work just fine. Retaining the RB+EEPROM (used by the original firmware to...I don't even know what it does as this Gotek variant does not behave like normal Goteks, so formatting your drive into multiple segments of 1.44MB in size is not going to work)...is purely up to you. I disconnected RB but kept the EEPROM alone on mine.

Things to be aware of -

  • The 26 pin FFC model runs on 5v, pins 1, 3 and 5 on the ribbon cable connector are power input rails (pin 1 is on the very left side of the FFC connector). If you need to run continuity checks between the 5v pin and the power, test pin 1 on the CPU (see below) with the 5v pin, and pins 1, 3 or 5 on the ribbon cable connector.
  • the standard Gotek bottom pin-outs from the Flashfloppy modification guide will also work with this model...you would have to solder the pins on and check your work accordingly (see test point locations on the photo and described later)

[Boot0] [3.3] [TX] [RX] [RST] [5v] [GND]

The following pins on the output corresponds to the following pinout on the STM32F105 LQFP64 package, and with the colors noted on the diagram below.

  • The LQFP64 package contains 16 pins per side, 4 sides, and pin 1 starts on the bottom row on the left and proceeds counter-clockwise around the chip until pin 64 on the left side of the CPU on the bottom.

5v - Pin1 (VBAT) Red Boot0 - Pin 60 (Boot0), Purple TX - Pin 42 (J? next to J4, PA09), Green RX - Pin 43 (J4, PA10), Blue

There is an AMS1117 voltage regulator(SOT223 package) with 3 pins, denoted on the board as U4. Left is GND, middle is 3.3v, and right is 5v.

On the SFRC2D/A the display connector is the following from left to right:

[SDA] [SCL] [GND] [3.3V] SCL - PIn 29 (PB10) - Yellow SDA - Pin 30 (PB11) - Orange

Ground is denoted as Black, and 3.3v is denoted as Orange-Red.

To program the SFRC2D/A with a USB-TTL serial adapter (preferably one that can do both 3.3/5v with the flick of a jumper), put a jumper between Boot0 and 3.3v, TX and TX to the correct pins, run VCC to the 5v pin (below J4), and ground to the GND pin (below RST), and follow the usual instructions.

There are existing test points on the board that can be used to verify that the soldering has been done correctly. See the attached photo for an idea of where they are located. Test points for RX/TX is above the STM105, Boot0 is to the left of the STM32F105, SDA/SCL is to the right (SDA will require you to test continuity with pin 27 directly), and 5v is present in at least 4 locations + the right leg off U4. 3.3v is supposed to be on the rightmost pin of the display pinout and on the middle leg off U4. @keirf you might find this photo of the SFRC2DA useful:

SFRC2DA-Annotated

Hope this bit is useful for those trying to make this device do useful things - the SFR1M44-GU26 have practically no open documentation available whatsoever besides "buy this overpriced Gotek variant" and a poorly translated instruction manual of questionable applicability. @mbirth The default firmware is utterly useless crap if you plan to work with non-standard disk images, like the 1.72MB XDF images used by IBM's OS/2. For 1.44MB floppies it's not that difficult to grab a disk image template and have the FDC write/save it to a blank disk image, save it and then rename it on the USB stick later.

@oldtrusty did your model come with the jumpers for the bottom headers? I noticed that on mine the JD/JE headers were jumped...not sure if this might impact your Oscilloscope reading the device.

I don't suppose you have a copy of your ff.cfg? I'm trying to run mine on a ThinkPad 755C. The drive will boot images, but sometimes has trouble switching images. Also, ThinkPad diags and software setup think there's no floppy installed (but swapping in the Teac FD-05HG it came with shows up), but I can still read it most of the time. Problematic areas are writing images with IBM's loaddskf or equivalent, rawrite2 for Linux, and reading the root image and beyond on Linux. I was, however, able to install OS/2 2.1 from start to finish.

pablogventura commented 1 year ago

I followed these instructions along with the standard FlashFloppy installation guide and it worked perfectly on a variant SFRC2DA board. Even the OLED screen remained functional. It was to restore a laptop from the 90's, an Epson Action Note 4SLC/33. Thank you!

bodong001 commented 2 months ago

Hello everyone, I really need your help. Regarding this floppy drive simulator, can you provide photos of the back of the PCB to determine the direction of certain pins of the 26 pin connector. Thank you, may you all be happy in the long run!

Wierzbowsky commented 2 months ago

@bodong001 Will this help? schematics

bodong001 commented 2 months ago

Thank you Wierzbowsky ! My problem has been solved. It was caused by me forgetting to close the SO jumper. In addition, according to your prompt, I modified pin 2 of pin 34. Now the oscilloscope is working very happily! Thank you again!

liveboxandy commented 1 month ago

From pictures and the use of a meter I have created what should be a schematic for the above Artery version SFRC2D.B. Should be the same as the STM version as a couple of smoothing caps make no sense on the Artery but do on the STM105.

Gotek.pdf I have also created a Kicad project for the above at https://github.com/liveboxandy/Gotek-SFRC2DB. Hope someone finds this useful.

keirf commented 1 month ago

@liveboxandy Thanks, I have linked to your repository from the FlashFloppy wiki.