AX6S不定时自动重启

[ERxhao]

` ____ __ / __ _ \ _ _ | /| / /_ _/ _/ / // / // / / / / / |/ |/ / / / / ____/ ./\/// //__/|/ // _/ /_/

---

           OpenWrt 08.02.2022 by Kiddin'
     _________________________________________

系统负载: 0.33 0.25 0.21 运行时间: 21 min
内存已用: 21 % of 227MB IP 地址: 192.168.0.1 系统存储: 17% of 78.7M CPU 信息: ARMv8 Processor x 2

[root@OpenWrt:02:28 PM ~] # cat /sys/fs/pstore/* Oops#1 Part1

<6>[ 9.048398] tun: Universal TUN/TAP device driver, 1.6 <6>[ 9.074886] cryptodev: driver 1.12 loaded. <6>[ 9.081134] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064 <6>[ 9.088728] Backport generated by backports.git v5.15.58-1-0-g42a95ce7 <6>[ 9.116066] xt_time: kernel timezone is -0000 <7>[ 9.172139] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' <7>[ 9.183164] mt7915e 0000:01:00.0: assign IRQ: got 142 <7>[ 9.188314] pci 0000:00:00.0: enabling bus mastering <6>[ 9.193291] mt7915e 0000:01:00.0: enabling device (0000 -> 0002) <7>[ 9.199395] mt7915e 0000:01:00.0: enabling bus mastering <6>[ 9.261106] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a <6>[ 9.261106] <6>[ 9.366162] mt7622-wmac 18000000.wmac: N9 Firmware Version: _reserved_, Build Time: 20220630094834 <6>[ 9.408501] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a <6>[ 9.408501] <6>[ 9.549747] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052 <6>[ 9.614454] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111 <6>[ 9.735732] PPP generic driver version 2.4.2 <6>[ 9.740941] PPP MPPE Compression module registered <6>[ 9.746777] NET: Registered protocol family 24 <14>[ 9.753146] kmodloader: done loading kernel modules from /etc/modules.d/* <6>[ 10.355906] zram0: detected capacity change from 0 to 78643200 <6>[ 10.426265] Adding 76796k swap on /dev/zram0. Priority:100 extents:1 across:76796k SSDsc <6>[ 12.700070] mtk_soc_eth 1b100000.ethernet eth0: Link is Down <6>[ 12.703505] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode <6>[ 12.703677] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 12.703695] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <6>[ 12.707013] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode <6>[ 12.707758] 8021q: adding VLAN 0 to HW filter on device lan1 <6>[ 12.712393] br-lan: port 1(lan1) entered blocking state <6>[ 12.712404] br-lan: port 1(lan1) entered disabled state <6>[ 12.716849] device lan1 entered promiscuous mode <6>[ 12.716857] device eth0 entered promiscuous mode <6>[ 12.726779] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode <6>[ 12.727334] 8021q: adding VLAN 0 to HW filter on device lan2 <6>[ 12.731970] br-lan: port 2(lan2) entered blocking state <6>[ 12.731981] br-lan: port 2(lan2) entered disabled state <6>[ 12.732684] device lan2 entered promiscuous mode <6>[ 12.741533] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode <6>[ 12.743953] 8021q: adding VLAN 0 to HW filter on device lan3 <6>[ 12.748836] mt7530 mdio-bus:00 lan3: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 12.752498] br-lan: port 3(lan3) entered blocking state <6>[ 12.752509] br-lan: port 3(lan3) entered disabled state <6>[ 12.753896] device lan3 entered promiscuous mode <6>[ 12.756669] br-lan: port 3(lan3) entered blocking state <6>[ 12.756681] br-lan: port 3(lan3) entered forwarding state <6>[ 12.756768] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready <6>[ 12.769739] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode <6>[ 12.770260] 8021q: adding VLAN 0 to HW filter on device wan <6>[ 12.774823] mt7530 mdio-bus:00 wan: Link is Up - 1Gbps/Full - flow control off <6>[ 12.777093] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready <6>[ 13.159944] pppoe-wan: renamed from ppp0 <6>[ 13.433189] mt7530 mdio-bus:00 lan2: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 14.286329] mt7530 mdio-bus:00 lan2: Link is Down <6>[ 14.294018] mt7530 mdio-bus:00 lan1: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 15.002148] br-lan: port 1(lan1) entered blocking state <6>[ 15.002168] br-lan: port 1(lan1) entered forwarding state <6>[ 15.259329] br-lan: port 4(wlan0) entered blocking state <6>[ 15.259342] br-lan: port 4(wlan0) entered disabled state <6>[ 15.259568] device wlan0 entered promiscuous mode <6>[ 15.259640] br-lan: port 4(wlan0) entered blocking state <6>[ 15.259647] br-lan: port 4(wlan0) entered forwarding state <6>[ 15.918171] mt7530 mdio-bus:00 lan2: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 15.918229] br-lan: port 2(lan2) entered blocking state <6>[ 15.918243] br-lan: port 2(lan2) entered forwarding state <6>[ 16.006841] br-lan: port 4(wlan0) entered disabled state <6>[ 16.640989] br-lan: port 5(wlan1) entered blocking state <6>[ 16.641001] br-lan: port 5(wlan1) entered disabled state <6>[ 16.641170] device wlan1 entered promiscuous mode <6>[ 16.641231] br-lan: port 5(wlan1) entered blocking state <6>[ 16.641237] br-lan: port 5(wlan1) entered forwarding state <6>[ 17.038752] br-lan: port 5(wlan1) entered disabled state <6>[ 17.940844] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready <6>[ 17.941026] br-lan: port 5(wlan1) entered blocking state <6>[ 17.941035] br-lan: port 5(wlan1) entered forwarding state <6>[ 22.031440] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready <6>[ 22.031584] br-lan: port 4(wlan0) entered blocking state <6>[ 22.031593] br-lan: port 4(wlan0) entered forwarding state <1>[10901.799290] Unable to handle kernel paging request at virtual address dead000000000110 <1>[10901.807213] Mem abort info: <1>[10901.810041] ESR = 0x96000004 <1>[10901.813095] EC = 0x25: DABT (current EL), IL = 32 bits <1>[10901.818401] SET = 0, FnV = 0 <1>[10901.821489] EA = 0, S1PTW = 0 <1>[10901.824646] Data abort info: <1>[10901.827516] ISV = 0, ISS = 0x00000004 <1>[10901.831378] CM = 0, WnR = 0 <1>[10901.834364] [dead000000000110] address between user and kernel address ranges <0>[10901.841554] Internal error: Oops: 96000004 [#1] SMP <7>[10901.846425] Modules linked in: pppoe ppp_async pppox ppp_mppe ppp_generic mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_state xt_quota xt_pkttype xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_cgroup xt_addrtype xt_TPROXY xt_TCPMSS xt_REDIRECT xt_MASQUERADE xt_LOG xt_FLOWOFFLOAD xt_CT tcp_bbr slhc nf_tproxy_ipv6 nf_tproxy_ipv4 nf_reject_ipv4 nf_log_ipv6 nf_log_ipv4 nf_log_common nf_flow_table nf_conntrack_netlink macvlan iptable_nat iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat cryptodev xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6t_NPT ip6table_mangle <7>[10901.846575] ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 tun zram zsmalloc crypto_user algif_skcipher algif_rng algif_hash algif_aead af_alg sha1_generic seqiv authenc arc4 leds_gpio gpio_button_hotplug <7>[10901.952790] CPU: 1 PID: 4271 Comm: kworker/u4:3 Not tainted 5.10.134 #0 <7>[10901.959392] Hardware name: Xiaomi Redmi Router AX6S (DT) <7>[10901.964712] Workqueue: nf_ft_offload_stats nf_flow_table_offload_setup [nf_flow_table] <7>[10901.972622] pstate: 20000005 (nzCv daif -PAN -UAO -TCO BTYPE=--) <7>[10901.978622] pc : nf_flow_offload_ip_hook+0x7c4/0x138c [nf_flow_table] <7>[10901.985056] lr : nf_flow_offload_ip_hook+0x7d8/0x138c [nf_flow_table] <7>[10901.991485] sp : ffffffc014a5bc20 <7>[10901.994789] x29: ffffffc014a5bc20 x28: 0000000000000000 <7>[10902.000093] x27: ffffff80038a4248 x26: 0000000000000000 <7>[10902.005397] x25: ffffff8001b71a00 x24: ffffffc008ab9660 <7>[10902.010702] x23: ffffffc014a5bd40 x22: 0000000000000002 <7>[10902.016007] x21: ffffffc008ab9650 x20: 0000000000000000 <7>[10902.021311] x19: dead0000000000f0 x18: 0000000000000000 <7>[10902.026615] x17: 0000000000000015 x16: ffffffc0108185d0 <7>[10902.031919] x15: 000000000000003d x14: 0000000000000000 <7>[10902.037224] x13: ffffffc008ab9398 x12: ffffffffffffffff <7>[10902.042528] x11: 0000000000000008 x10: ffffff8000005100 <7>[10902.047832] x9 : ffffff8003afff7c x8 : 0000000000000000 <7>[10902.053136] x7 : ffffffffffffffff x6 : 0089e70200000000 <7>[10902.058441] x5 : 0000000000000002 x4 : 0000000000000000 <7>[10902.063744] x3 : ffffff800018ad00 x2 : 0000000000000000 <7>[10902.069049] x1 : dead000000000100 x0 : 0000000000000001 <7>[10902.074354] Call trace: <7>[10902.076795] nf_flow_offload_ip_hook+0x7c4/0x138c [nf_flow_table] <7>[10902.082880] nf_flow_table_offload_setup+0x478/0x670 [nf_flow_table] <7>[10902.089230] process_one_work+0x1d4/0x370 <7>[10902.093231] worker_thread+0x178/0x4e0 <7>[10902.096971] kthread+0x120/0x124 <7>[10902.100192] ret_from_fork+0x10/0x18 <0>[10902.103761] Code: d1004013 eb0002bf 54000580 52800014 (f9401263) <4>[10902.109846] ---[ end trace 35a8132a39490859 ]--- Panic#2 Part1 <6>[ 9.116066] xt_time: kernel timezone is -0000 <7>[ 9.172139] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' <7>[ 9.183164] mt7915e 0000:01:00.0: assign IRQ: got 142 <7>[ 9.188314] pci 0000:00:00.0: enabling bus mastering <6>[ 9.193291] mt7915e 0000:01:00.0: enabling device (0000 -> 0002) <7>[ 9.199395] mt7915e 0000:01:00.0: enabling bus mastering <6>[ 9.261106] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a <6>[ 9.261106] <6>[ 9.366162] mt7622-wmac 18000000.wmac: N9 Firmware Version: _reserved_, Build Time: 20220630094834 <6>[ 9.408501] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a <6>[ 9.408501] <6>[ 9.549747] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052 <6>[ 9.614454] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111 <6>[ 9.735732] PPP generic driver version 2.4.2 <6>[ 9.740941] PPP MPPE Compression module registered <6>[ 9.746777] NET: Registered protocol family 24 <14>[ 9.753146] kmodloader: done loading kernel modules from /etc/modules.d/* <6>[ 10.355906] zram0: detected capacity change from 0 to 78643200 <6>[ 10.426265] Adding 76796k swap on /dev/zram0. Priority:100 extents:1 across:76796k SSDsc <6>[ 12.700070] mtk_soc_eth 1b100000.ethernet eth0: Link is Down <6>[ 12.703505] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode <6>[ 12.703677] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 12.703695] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <6>[ 12.707013] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode <6>[ 12.707758] 8021q: adding VLAN 0 to HW filter on device lan1 <6>[ 12.712393] br-lan: port 1(lan1) entered blocking state <6>[ 12.712404] br-lan: port 1(lan1) entered disabled state <6>[ 12.716849] device lan1 entered promiscuous mode <6>[ 12.716857] device eth0 entered promiscuous mode <6>[ 12.726779] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode <6>[ 12.727334] 8021q: adding VLAN 0 to HW filter on device lan2 <6>[ 12.731970] br-lan: port 2(lan2) entered blocking state <6>[ 12.731981] br-lan: port 2(lan2) entered disabled state <6>[ 12.732684] device lan2 entered promiscuous mode <6>[ 12.741533] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode <6>[ 12.743953] 8021q: adding VLAN 0 to HW filter on device lan3 <6>[ 12.748836] mt7530 mdio-bus:00 lan3: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 12.752498] br-lan: port 3(lan3) entered blocking state <6>[ 12.752509] br-lan: port 3(lan3) entered disabled state <6>[ 12.753896] device lan3 entered promiscuous mode <6>[ 12.756669] br-lan: port 3(lan3) entered blocking state <6>[ 12.756681] br-lan: port 3(lan3) entered forwarding state <6>[ 12.756768] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready <6>[ 12.769739] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode <6>[ 12.770260] 8021q: adding VLAN 0 to HW filter on device wan <6>[ 12.774823] mt7530 mdio-bus:00 wan: Link is Up - 1Gbps/Full - flow control off <6>[ 12.777093] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready <6>[ 13.159944] pppoe-wan: renamed from ppp0 <6>[ 13.433189] mt7530 mdio-bus:00 lan2: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 14.286329] mt7530 mdio-bus:00 lan2: Link is Down <6>[ 14.294018] mt7530 mdio-bus:00 lan1: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 15.002148] br-lan: port 1(lan1) entered blocking state <6>[ 15.002168] br-lan: port 1(lan1) entered forwarding state <6>[ 15.259329] br-lan: port 4(wlan0) entered blocking state <6>[ 15.259342] br-lan: port 4(wlan0) entered disabled state <6>[ 15.259568] device wlan0 entered promiscuous mode <6>[ 15.259640] br-lan: port 4(wlan0) entered blocking state <6>[ 15.259647] br-lan: port 4(wlan0) entered forwarding state <6>[ 15.918171] mt7530 mdio-bus:00 lan2: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 15.918229] br-lan: port 2(lan2) entered blocking state <6>[ 15.918243] br-lan: port 2(lan2) entered forwarding state <6>[ 16.006841] br-lan: port 4(wlan0) entered disabled state <6>[ 16.640989] br-lan: port 5(wlan1) entered blocking state <6>[ 16.641001] br-lan: port 5(wlan1) entered disabled state <6>[ 16.641170] device wlan1 entered promiscuous mode <6>[ 16.641231] br-lan: port 5(wlan1) entered blocking state <6>[ 16.641237] br-lan: port 5(wlan1) entered forwarding state <6>[ 17.038752] br-lan: port 5(wlan1) entered disabled state <6>[ 17.940844] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready <6>[ 17.941026] br-lan: port 5(wlan1) entered blocking state <6>[ 17.941035] br-lan: port 5(wlan1) entered forwarding state <6>[ 22.031440] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready <6>[ 22.031584] br-lan: port 4(wlan0) entered blocking state <6>[ 22.031593] br-lan: port 4(wlan0) entered forwarding state <1>[10901.799290] Unable to handle kernel paging request at virtual address dead000000000110 <1>[10901.807213] Mem abort info: <1>[10901.810041] ESR = 0x96000004 <1>[10901.813095] EC = 0x25: DABT (current EL), IL = 32 bits <1>[10901.818401] SET = 0, FnV = 0 <1>[10901.821489] EA = 0, S1PTW = 0 <1>[10901.824646] Data abort info: <1>[10901.827516] ISV = 0, ISS = 0x00000004 <1>[10901.831378] CM = 0, WnR = 0 <1>[10901.834364] [dead000000000110] address between user and kernel address ranges <0>[10901.841554] Internal error: Oops: 96000004 [#1] SMP <7>[10901.846425] Modules linked in: pppoe ppp_async pppox ppp_mppe ppp_generic mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_state xt_quota xt_pkttype xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_cgroup xt_addrtype xt_TPROXY xt_TCPMSS xt_REDIRECT xt_MASQUERADE xt_LOG xt_FLOWOFFLOAD xt_CT tcp_bbr slhc nf_tproxy_ipv6 nf_tproxy_ipv4 nf_reject_ipv4 nf_log_ipv6 nf_log_ipv4 nf_log_common nf_flow_table nf_conntrack_netlink macvlan iptable_nat iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat cryptodev xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6t_NPT ip6table_mangle <7>[10901.846575] ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 tun zram zsmalloc crypto_user algif_skcipher algif_rng algif_hash algif_aead af_alg sha1_generic seqiv authenc arc4 leds_gpio gpio_button_hotplug <7>[10901.952790] CPU: 1 PID: 4271 Comm: kworker/u4:3 Not tainted 5.10.134 #0 <7>[10901.959392] Hardware name: Xiaomi Redmi Router AX6S (DT) <7>[10901.964712] Workqueue: nf_ft_offload_stats nf_flow_table_offload_setup [nf_flow_table] <7>[10901.972622] pstate: 20000005 (nzCv daif -PAN -UAO -TCO BTYPE=--) <7>[10901.978622] pc : nf_flow_offload_ip_hook+0x7c4/0x138c [nf_flow_table] <7>[10901.985056] lr : nf_flow_offload_ip_hook+0x7d8/0x138c [nf_flow_table] <7>[10901.991485] sp : ffffffc014a5bc20 <7>[10901.994789] x29: ffffffc014a5bc20 x28: 0000000000000000 <7>[10902.000093] x27: ffffff80038a4248 x26: 0000000000000000 <7>[10902.005397] x25: ffffff8001b71a00 x24: ffffffc008ab9660 <7>[10902.010702] x23: ffffffc014a5bd40 x22: 0000000000000002 <7>[10902.016007] x21: ffffffc008ab9650 x20: 0000000000000000 <7>[10902.021311] x19: dead0000000000f0 x18: 0000000000000000 <7>[10902.026615] x17: 0000000000000015 x16: ffffffc0108185d0 <7>[10902.031919] x15: 000000000000003d x14: 0000000000000000 <7>[10902.037224] x13: ffffffc008ab9398 x12: ffffffffffffffff <7>[10902.042528] x11: 0000000000000008 x10: ffffff8000005100 <7>[10902.047832] x9 : ffffff8003afff7c x8 : 0000000000000000 <7>[10902.053136] x7 : ffffffffffffffff x6 : 0089e70200000000 <7>[10902.058441] x5 : 0000000000000002 x4 : 0000000000000000 <7>[10902.063744] x3 : ffffff800018ad00 x2 : 0000000000000000 <7>[10902.069049] x1 : dead000000000100 x0 : 0000000000000001 <7>[10902.074354] Call trace: <7>[10902.076795] nf_flow_offload_ip_hook+0x7c4/0x138c [nf_flow_table] <7>[10902.082880] nf_flow_table_offload_setup+0x478/0x670 [nf_flow_table] <7>[10902.089230] process_one_work+0x1d4/0x370 <7>[10902.093231] worker_thread+0x178/0x4e0 <7>[10902.096971] kthread+0x120/0x124 <7>[10902.100192] ret_from_fork+0x10/0x18 <0>[10902.103761] Code: d1004013 eb0002bf 54000580 52800014 (f9401263) <4>[10902.109846] ---[ end trace 35a8132a39490859 ]--- <0>[10902.119936] Kernel panic - not syncing: Oops: Fatal exception <2>[10902.125675] SMP: stopping secondary CPUs <0>[10902.129591] Kernel Offset: disabled <0>[10902.133073] CPU features: 0x0000002,04002004 <0>[10902.137333] Memory Limit: none `

[digiw]

如果安装了Watchcat 模块（服务菜单里），可以尝试把 默认的 8.8.8.8那个ip改成你能ping通的国内地址，就不会导致误判重启了，或者用不到的话你可以关闭这个模块，希望对你有帮助

[ERxhao]

如果安装了Watchcat模块（菜单地址里），可以试一下8.8.8.8那个ip成你ping通的国内模块，就不会导致判别重启了，或者这个用不到的话你可以关闭，希望对你有帮助

谢谢你提供的方法，我的 模块只安装了openchash upnp bypass 和自带的系统在线更新

[SRGOD]

同样ax6s，模块只装了 系统在线更新、bypass 和 upnp，也是不定时重启，每天大概重启3、4次。

[dreamflandre]

尝试下关闭网络-防火墙-路由/NAT 分载？我之前也是没装啥也反复重启，关了就稳定多了.

[SRGOD]

我的 网络-防火墙 页面里面没有路由/Nat 分载 这一项啊..