SOEKRIS 4801 boots OpenBSD 5.3, but I never see a login prompt

[jrmakosky]

After adjusting the kernel config per issue 19, my Soekris 4801 boots, but never gives me a login prompt. I have tried two different terminals (cu and screen). The console still accepts keyboard input. The system responds to pings on sis0.

comBIOS ver. 1.31  20070408  Copyright (C) 2000-2007 Soekris Engineering.

net4801

0128 Mbyte Memory                        CPU Geode SC1100 267 Mhz 

Pri Mas  SanDisk SDCFB-64                LBA 978-4-32  62 Mbyte

Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int 
-------------------------------------------------------------------
0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000 
0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10
0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002000 10
0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000 
0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 A0003000 00000000 11

 1 Seconds to automatic boot.   Press Ctrl-P for entering Monitor.
Using drive 0, partition 3.
Loading.....
probing: pc0 com0 com1 pci mem[639K 127M a20=on] 
disk: hd0+
>> OpenBSD/i386 BOOT 3.21
switching console to com0
                         >> OpenBSD/i386 BOOT 3.21
boot> 
booting hd0a:/bsd: 53915540+477336 [52+146736+139968]=0x34259c4
entry point at 0x200120

[ using 287128 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2013 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 5.3 (SOEKRIS4801) #0: Tue Jun 11 10:12:02 MDT 2013
    root@tybalt.localdomain:/obj/SOEKRIS4801
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC" 586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
real mem  = 133754880 (127MB)
avail mem = 76910592 (73MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/70/08, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0: (uniprocessor)
cpu0: TSC disabled
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c2:c3:d0
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c2:c3:d1
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c2:c3:d2
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
pcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFB-64>
wd0: 1-sector PIO, LBA, 61MB, 125184 sectors
wd0(pciide0:0:0): using PIO mode 1
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6 revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 11, version 1.0, legacy support
isa0 at pcib0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio0 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1
root on rd0a swap on rd0b dump on rd0b
********* flashboot
/dev/rwd0a: file system is clean; not checking
/dev/rwd0a: file system is clean; not checking
Copying additional configuration files from flash to ramdisk
setting tty flags
building ps databases: dev.
net.inet.tcp.ecn: 0 -> 1
ddb.panic: 1 -> 0
ddb.console: 0 -> 1
kern.splassert: 1 -> 2
pf enabled
starting network
WARNING: /etc/hostname.em0 is insecure, fixing permissions
WARNING: /etc/hostname.rl0 is insecure, fixing permissions
WARNING: /etc/hostname.sis0 is insecure, fixing permissions
WARNING: /etc/hostname.vr0 is insecure, fixing permissions
Daemons: starting system logger
 inetd cron.
********* executing /etc/rc.pkg
********* finished /etc/rc.pkg
********* finished /etc/rc
Jun  7 13:48:50 localhost init: kernel security level changed from 0 to 1

[jrmakosky]

Boots into single user mode with no obvious problems.

[jschlyter]

Should be fixed now, please verify.

[jrmakosky]

Fix has been confirmed. Thank you @sthen.