search

kriswiner / CMWX1ZZABZ

Collection of sketches using the Arduino core for Murata's CMWX1ZZABZ (STM32L082 and SX1276)
93 stars 29 forks source link

GNAT STM32 bootloader/usb driver problem #11

Open everhamme opened 5 years ago

everhamme commented 5 years ago

I connected my new gnat to my computer just fine and compiled a new example sketch from the github. I was able to select the Cricket board from the board manager, correct com port, and load the new sketch just fine. After the sketch loaded I went to open the serial monitor and arduino ide said the com port wasn't found. If I look in my device manager (win 10 64 bit) I only see the STM32 BOOTLOADER showing up under USB devices. No entry showing up in the Ports section. I did the reset option (hold down boot and toggle reset). This doesn't fix the issue. I can hook up my cicada/loratile device and it shows up just fine. any other troubleshooting things to try to get the com port back?

kriswiner commented 5 years ago

Download the latest Arduino core and use the Gnat variant. The Cricket variant will not work.

On Wed, Jan 16, 2019 at 10:08 AM Ed Verhamme notifications@github.com wrote:

I connected my new gnat to my computer just fine and compiled a new example sketch from the github. I was able to select the Cricket board from the board manager, correct com port, and load the new sketch just fine. After the sketch loaded I went to open the serial monitor and arduino ide said the com port wasn't found. If I look in my device manager (win 10 64 bit) I only see the STM32 BOOTLOADER showing up under USB devices. No entry showing up in the Ports section. I did the reset option (hold down boot and toggle reset). This doesn't fix the issue. I can hook up my cicada/loratile device and it shows up just fine. any other troubleshooting things to try to get the com port back?

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/kriswiner/CMWX1ZZABZ/issues/11, or mute the thread https://github.com/notifications/unsubscribe-auth/AGY1qvtm9GF4mvbHVQ2gydNoBwk6jD44ks5vD2qWgaJpZM4aDpaw .

everhamme commented 5 years ago

Oops.. I should have selected gnat.. how do I get com port back?

From: Kris Winer [mailto:notifications@github.com] Sent: Wednesday, January 16, 2019 1:11 PM To: kriswiner/CMWX1ZZABZ CMWX1ZZABZ@noreply.github.com Cc: Ed Verhamme everhamme@limno.com; Author author@noreply.github.com Subject: Re: [kriswiner/CMWX1ZZABZ] GNAT STM32 bootloader/usb driver problem (#11)

Download the latest Arduino core and use the Gnat variant. The Cricket variant will not work.

On Wed, Jan 16, 2019 at 10:08 AM Ed Verhamme notifications@github.com<mailto:notifications@github.com> wrote:

I connected my new gnat to my computer just fine and compiled a new example sketch from the github. I was able to select the Cricket board from the board manager, correct com port, and load the new sketch just fine. After the sketch loaded I went to open the serial monitor and arduino ide said the com port wasn't found. If I look in my device manager (win 10 64 bit) I only see the STM32 BOOTLOADER showing up under USB devices. No entry showing up in the Ports section. I did the reset option (hold down boot and toggle reset). This doesn't fix the issue. I can hook up my cicada/loratile device and it shows up just fine. any other troubleshooting things to try to get the com port back?

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/kriswiner/CMWX1ZZABZ/issues/11, or mute the thread https://github.com/notifications/unsubscribe-auth/AGY1qvtm9GF4mvbHVQ2gydNoBwk6jD44ks5vD2qWgaJpZM4aDpaw .

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHubhttps://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454881744, or mute the threadhttps://github.com/notifications/unsubscribe-auth/ALbbGgE28XoVrNVAhJJF8d4cEPLFxzscks5vD2scgaJpZM4aDpaw.

kriswiner commented 5 years ago

Close Arduino IDE. Press and hold BTN, press and release RST, release BTN. Open Arduino IDE, select Gnat board variant, flash a blink program (no COM port should show). After flash the laptop will assign a COM port.

On Wed, Jan 16, 2019 at 10:12 AM Ed Verhamme notifications@github.com wrote:

Oops.. I should have selected gnat.. how do I get com port back?

From: Kris Winer [mailto:notifications@github.com] Sent: Wednesday, January 16, 2019 1:11 PM To: kriswiner/CMWX1ZZABZ CMWX1ZZABZ@noreply.github.com Cc: Ed Verhamme everhamme@limno.com; Author author@noreply.github.com Subject: Re: [kriswiner/CMWX1ZZABZ] GNAT STM32 bootloader/usb driver problem (#11)

Download the latest Arduino core and use the Gnat variant. The Cricket variant will not work.

On Wed, Jan 16, 2019 at 10:08 AM Ed Verhamme <notifications@github.com mailto:notifications@github.com> wrote:

I connected my new gnat to my computer just fine and compiled a new example sketch from the github. I was able to select the Cricket board from the board manager, correct com port, and load the new sketch just fine. After the sketch loaded I went to open the serial monitor and arduino ide said the com port wasn't found. If I look in my device manager (win 10 64 bit) I only see the STM32 BOOTLOADER showing up under USB devices. No entry showing up in the Ports section. I did the reset option (hold down boot and toggle reset). This doesn't fix the issue. I can hook up my cicada/loratile device and it shows up just fine. any other troubleshooting things to try to get the com port back?

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/kriswiner/CMWX1ZZABZ/issues/11, or mute the thread < https://github.com/notifications/unsubscribe-auth/AGY1qvtm9GF4mvbHVQ2gydNoBwk6jD44ks5vD2qWgaJpZM4aDpaw>

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub< https://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454881744>, or mute the thread< https://github.com/notifications/unsubscribe-auth/ALbbGgE28XoVrNVAhJJF8d4cEPLFxzscks5vD2scgaJpZM4aDpaw>.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454882494, or mute the thread https://github.com/notifications/unsubscribe-auth/AGY1qna0HGUsntckSt8Z-Yt1WU6761O6ks5vD2uhgaJpZM4aDpaw .

everhamme commented 5 years ago

Working!

From: Kris Winer [mailto:notifications@github.com] Sent: Wednesday, January 16, 2019 2:09 PM To: kriswiner/CMWX1ZZABZ CMWX1ZZABZ@noreply.github.com Cc: Ed Verhamme everhamme@limno.com; Author author@noreply.github.com Subject: Re: [kriswiner/CMWX1ZZABZ] GNAT STM32 bootloader/usb driver problem (#11)

Close Arduino IDE. Press and hold BTN, press and release RST, release BTN. Open Arduino IDE, select Gnat board variant, flash a blink program (no COM port should show). After flash the laptop will assign a COM port.

On Wed, Jan 16, 2019 at 10:12 AM Ed Verhamme notifications@github.com<mailto:notifications@github.com> wrote:

Oops.. I should have selected gnat.. how do I get com port back?

From: Kris Winer [mailto:notifications@github.com] Sent: Wednesday, January 16, 2019 1:11 PM To: kriswiner/CMWX1ZZABZ CMWX1ZZABZ@noreply.github.com<mailto:CMWX1ZZABZ@noreply.github.com> Cc: Ed Verhamme everhamme@limno.com<mailto:everhamme@limno.com>; Author author@noreply.github.com<mailto:author@noreply.github.com> Subject: Re: [kriswiner/CMWX1ZZABZ] GNAT STM32 bootloader/usb driver problem (#11)

Download the latest Arduino core and use the Gnat variant. The Cricket variant will not work.

On Wed, Jan 16, 2019 at 10:08 AM Ed Verhamme <notifications@github.com mailto:notifications@github.com%0b> mailto:notifications@github.com> wrote:

I connected my new gnat to my computer just fine and compiled a new example sketch from the github. I was able to select the Cricket board from the board manager, correct com port, and load the new sketch just fine. After the sketch loaded I went to open the serial monitor and arduino ide said the com port wasn't found. If I look in my device manager (win 10 64 bit) I only see the STM32 BOOTLOADER showing up under USB devices. No entry showing up in the Ports section. I did the reset option (hold down boot and toggle reset). This doesn't fix the issue. I can hook up my cicada/loratile device and it shows up just fine. any other troubleshooting things to try to get the com port back?

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/kriswiner/CMWX1ZZABZ/issues/11, or mute the thread < https://github.com/notifications/unsubscribe-auth/AGY1qvtm9GF4mvbHVQ2gydNoBwk6jD44ks5vD2qWgaJpZM4aDpaw>

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub< https://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454881744>, or mute the thread< https://github.com/notifications/unsubscribe-auth/ALbbGgE28XoVrNVAhJJF8d4cEPLFxzscks5vD2scgaJpZM4aDpaw>.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454882494, or mute the thread https://github.com/notifications/unsubscribe-auth/AGY1qna0HGUsntckSt8Z-Yt1WU6761O6ks5vD2uhgaJpZM4aDpaw .

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHubhttps://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454901401, or mute the threadhttps://github.com/notifications/unsubscribe-auth/ALbbGqvQSFky-d9o9Cpf77WsVeFbWapvks5vD3i6gaJpZM4aDpaw.

kriswiner commented 5 years ago

Yup, if you ever load a program with the wrong board variant and get stuck this procedure will work.

On Wed, Jan 16, 2019 at 12:28 PM Ed Verhamme notifications@github.com wrote:

Working!

From: Kris Winer [mailto:notifications@github.com] Sent: Wednesday, January 16, 2019 2:09 PM To: kriswiner/CMWX1ZZABZ CMWX1ZZABZ@noreply.github.com Cc: Ed Verhamme everhamme@limno.com; Author author@noreply.github.com Subject: Re: [kriswiner/CMWX1ZZABZ] GNAT STM32 bootloader/usb driver problem (#11)

Close Arduino IDE. Press and hold BTN, press and release RST, release BTN. Open Arduino IDE, select Gnat board variant, flash a blink program (no COM port should show). After flash the laptop will assign a COM port.

On Wed, Jan 16, 2019 at 10:12 AM Ed Verhamme <notifications@github.com mailto:notifications@github.com> wrote:

Oops.. I should have selected gnat.. how do I get com port back?

From: Kris Winer [mailto:notifications@github.com] Sent: Wednesday, January 16, 2019 1:11 PM To: kriswiner/CMWX1ZZABZ <CMWX1ZZABZ@noreply.github.com<mailto: CMWX1ZZABZ@noreply.github.com>> Cc: Ed Verhamme everhamme@limno.com<mailto:everhamme@limno.com>; Author author@noreply.github.com<mailto:author@noreply.github.com> Subject: Re: [kriswiner/CMWX1ZZABZ] GNAT STM32 bootloader/usb driver problem (#11)

Download the latest Arduino core and use the Gnat variant. The Cricket variant will not work.

On Wed, Jan 16, 2019 at 10:08 AM Ed Verhamme <notifications@github.com mailto:notifications@github.com%0b> mailto:notifications@github.com> wrote:

I connected my new gnat to my computer just fine and compiled a new example sketch from the github. I was able to select the Cricket board from the board manager, correct com port, and load the new sketch just fine. After the sketch loaded I went to open the serial monitor and arduino ide said the com port wasn't found. If I look in my device manager (win 10 64 bit) I only see the STM32 BOOTLOADER showing up under USB devices. No entry showing up in the Ports section. I did the reset option (hold down boot and toggle reset). This doesn't fix the issue. I can hook up my cicada/loratile device and it shows up just fine. any other troubleshooting things to try to get the com port back?

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/kriswiner/CMWX1ZZABZ/issues/11, or mute the thread <

https://github.com/notifications/unsubscribe-auth/AGY1qvtm9GF4mvbHVQ2gydNoBwk6jD44ks5vD2qWgaJpZM4aDpaw>

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub< https://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454881744>,

or mute the thread<

https://github.com/notifications/unsubscribe-auth/ALbbGgE28XoVrNVAhJJF8d4cEPLFxzscks5vD2scgaJpZM4aDpaw>.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub < https://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454882494>,

or mute the thread < https://github.com/notifications/unsubscribe-auth/AGY1qna0HGUsntckSt8Z-Yt1WU6761O6ks5vD2uhgaJpZM4aDpaw>

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub< https://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454901401>, or mute the thread< https://github.com/notifications/unsubscribe-auth/ALbbGqvQSFky-d9o9Cpf77WsVeFbWapvks5vD3i6gaJpZM4aDpaw>.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/CMWX1ZZABZ/issues/11#issuecomment-454928261, or mute the thread https://github.com/notifications/unsubscribe-auth/AGY1qj90KdpL3qwnJjgbXlb_-7xXKJ7Wks5vD4t4gaJpZM4aDpaw .