Open shomedas opened 4 years ago
This is not what I would have done. Sensor fusion is best done on the embedded MCU, and the ESP32 is more than capable to provide fast enough fusion rates to get good results. I suspect either the sensors are not calibrated sufficiently or you are not feeding the sensor data to the fusion filter in the proper order.
I have done testing with the Madgwick fusion filter and MPU9250 that shows pretty low latency response using similar MCUs (like Teensy or STM32L4-based MCUs). You should be able to get the same results with an ESP32. Here is some results using a Teensy 3.2 I believe:
https://github.com/kriswiner/MPU6050/wiki/9-DoF-Motion-Sensor-Bakeoff
Here is the sketch I used for the ESP32 to get similar results:
https://github.com/kriswiner/ESP32/tree/master/MPU9250_MS5637
On Mon, Oct 21, 2019 at 11:23 AM shomedas notifications@github.com wrote:
I had found that there is a delay(a few seconds) in the convergence of the heading quaternion when the IMU is moved randomly or fast. So I have ported the sensor fusion part of your code(the for loop having the madgwick update) to my desktop to get higher sensor fusion rates. I grab the accelerometer, gyroscope and the magnetometer readings from the MPU9250 using an ESP32 using the remaining part of your code. I calibrate the data in my desktop.
My question is what parameters do I need to change to attain faster convergence when I move around the IMU. I read from your git forum that accelerometer and gyroscope need to be sampled at 1Khz with 100 Hz Low Pass Filter, while magnetometer is to be left at 100Hz. I made the following changes in initMPU9250 function of your code
SMPLRT_DIV : changed it to 0x00 from 0x04 to set the accelerometer and gyroscope sampling rate at 1Khz writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x02)
DLPF_CFG changed it to 0x02 from 0x03 to set the gyro bandwidth to 92Hz writeByte(MPU9250_ADDRESS, CONFIG, 0x02)
c=c|0x02 ; // changed it to 0x02 from 0x03 to set the gyro bandwidth to 92Hz writeByte(MPU9250_ADDRESS, CONFIG, ACCEL_CONFIG2,c)
What other changes do I need to do? Do I need to change the i2c frequency to 1Mhz. Do I need to change the i2c resistance for operating at 1Mhz What about the baud rate between the ESP32 and the desktop?
— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKSGVXWRY6PRAE7WX2LQPXXR5A5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFUVEXG43VMWVGG33NNVSW45C7NFSM4HTIZGFQ, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKTCP76ZJUA5WV45ZN3QPXXR5ANCNFSM4JDC3OVQ .
kindly tell me if the variables I have changed are correct. I would try to run with the modified parameters on the esp32. Can I run 1Mhz i2c on esp32 for better results.
I get reliable heading estimate from esp32 under static condition or in slow movement with the IMU. If I move faster it takes time ( two or three seconds)to converge. I get sensor fusion rate of only 2khz on the esp32. So I thought I am restricted to 250hz sampling on accelerometer and gyroscope. Can I try higher sampling rates.
My magnetometer calibration is a perfect sphere. I have calibrated magnetometer using ellipsoid method. I have calibrated accelerometer using least squares method from AN4399 application note from freescale. Accelerometer calibration also should be nearly ok.
I don't have access to stm32 or tindie devices immediately. So I have to manage with esp32 or the desktop.
Kindly help.
Settings are fine. You might try 500 Hz or 1 kHz gyro/accel rate. 2 kHz fusion rate seems a bit slower than what I usually see, but i don't remember exactly. Still, if you are feeding the sensor data properly to the fusion filter and your sensors are calibrated then you should see much lower latency that a few seconds to converge.
On Mon, Oct 21, 2019 at 7:08 PM shomedas notifications@github.com wrote:
kindly tell me if the variables I have changed are correct. I would try to run with the modified parameters on the esp32. Can I run 1Mhz i2c on esp32 for better results.
I get reliable heading estimate from esp32 under static condition or in slow movement with the IMU. If I move faster it takes time ( two or three seconds)to converge. I get sensor fusion rate of only 2khz on the esp32. So I thought I am restricted to 250hz sampling on accelerometer and gyroscope. Can I try higher sampling rates.
My magnetometer calibration is a perfect sphere. I have calibrated magnetometer using ellipsoid method. I have calibrated accelerometer using least squares method from AN4399 application note from freescale. Accelerometer calibration also should be nearly ok.
I don't have access to stm32 or tindie devices immediately. So I have to manage with esp32 or the desktop.
Kindly help.
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKSDWCXH4UUBDD42OH3QPZOANA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB4KW7Y#issuecomment-544779135, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKSOACATYEAI7CQBUBTQPZOANANCNFSM4JDC3OVQ .
Thank you for your help, Kris
Kris, what low pass frequency filter should I use with 500hz sampling rate. Is 92Hz ok?
Yes.
The ESP32 is supposed to have a FPU so you should be seeing much higher fusion rates than 2 kHz with this.
I ran this sketch https://github.com/kriswiner/ESP8285/tree/master/MPU9250 with the MP9250 on the ESP8285 and got 2 kHz fusion rates. So something is wrong with your sketch perhaps.
Could be a buggy I2C API I suppose, but if you are using the data ready interrupt and aren't bogging the main loop down with lots of extraneous stuff you should be well over 10 kHz fusion rate with the ESP32.
In the ESP32 sketch I linked to before, I am only iterating the Madgwick filter 10 times because the fusion rate was way to fast, such that I was simply wasting cycles on iterating. Meaning the rate was >> 2 kHz when I ran my sketch. I suspect there is something wrong with yours, like you are polling for data ready or something else like this. Not good...
On Mon, Oct 21, 2019 at 7:59 PM shomedas notifications@github.com wrote:
Kris, what low pass frequency filter should I use with 500hz sampling rate. Is 92Hz ok?
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKXOZ4BXDC6TIIMUO3DQPZT73A5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB4MVXQ#issuecomment-544787166, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKT4ZX6WTYOX6HB6XELQPZT73ANCNFSM4JDC3OVQ .
Will the 8285 code link given in your post above work with the esp32?
Then I would try again with it
Maybe, why not just use the sketch I linked to yesterday specifically for the ESP32?
On Mon, Oct 21, 2019 at 8:45 PM shomedas notifications@github.com wrote:
Will the 8285 code link given in your post above work with the esp32?
Then I would try again with it
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKU2OPZLVH4UW7KTDJLQPZZMBA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB4OMEA#issuecomment-544794128, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKRXGH4U7YSDE35GEJ3QPZZMBANCNFSM4JDC3OVQ .
Sorry I thought you were referring to the link in your post above.
I have been using the esp32 code(with some modifications) as you mentioned in your post yesterday. I will remove any unnecessary part and try again.
Thanks for your he
Are you using the data ready interrupt and 400 kHz I2C?
On Mon, Oct 21, 2019 at 9:12 PM shomedas notifications@github.com wrote:
Sorry I thought you were referring to the link in your post above.
I have been using the esp32 code(with some modifications) as you mentioned in your post yesterday. I will remove any unnecessary part and try again.
Thanks for your he
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKTEOOCY7UKYOES3KDLQPZ4RRA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB4PLGA#issuecomment-544798104, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKQBBYQLJVCL5PS5GUDQPZ4RRANCNFSM4JDC3OVQ .
I am using i2c an 400Kh.I am using data ready interrupt as below. In fact, if the interrupt pin is disconnected, I get constant quaternion of (1,0,0,0).
void setup() { .... attachInterrupt(digitalPinToInterrupt(intPin), myinthandler, RISING); // define interrupt for INT pin output of MPU9250 }
void loop{ // If intPin goes high, all data registers have new data if(newData == true) { // On interrupt, read data newData = false; // reset newData flag readMPU9250Data(MPU9250Data); // INT cleared on any read ... }
Then your fusion rate should be >> 2 kHz.
On Mon, Oct 21, 2019 at 9:52 PM shomedas notifications@github.com wrote:
I am using i2c an 400Kh.I am using data ready interrupt as below. In fact, if the interrupt pin is disconnected, I get constant quaternion of (1,0,0,0).
void setup() { .... attachInterrupt(digitalPinToInterrupt(intPin), myinthandler, RISING); // define interrupt for INT pin output of MPU9250 }
void loop{ // If intPin goes high, all data registers have new data if(newData == true) { // On interrupt, read data newData = false; // reset newData flag readMPU9250Data(MPU9250Data); // INT cleared on any read ... }
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKRBV5T6WCTQJFNETKTQP2BHTA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB4QZWI#issuecomment-544804057, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKT6Z4Q3APINIIXOGQLQP2BHTANCNFSM4JDC3OVQ .
I am going to run your original sketch again and report back.
No kris i still get ~2Kz fusion rate. i have used your code at https://github.com/kriswiner/ESP32/tree/master/MPU9250_MS5637. I have removed only those parts pertaining to 5637 sensor. Everything else is the same. I dont have accurate calibration, but that should not change the sensor fusion rate.
I get q0 = 0.38 qx = 0.09 qy = 0.90 qz = -0.19 Yaw, Pitch, Roll: 192.70, 45.95, -156.87 Grav_x, Grav_y, Grav_z: 273.15, 718.68, -639.44 mg Lin_ax, Lin_ay, Lin_az: -279.74, -695.43, 1637.67 mg sumCount = 1010 sum = 0.51 rate = 1981.34 Hz
I am attaching herewith your original code from link without the 5637 part. if you can spare some time please check if you get >> 2KHz fusion rate with esp32. I have been experimenting with it for months but I only get 2Khz.
I have tried with esp-arduino board managers version 1.01, 1.02, 1.03 and 1.04(latest) all giving the same result ie. 2KHz sensor fusion rate.
/* MPU9250_MS5637_ESP32 Basic Example Code
by: Kris Winer
date: December 14, 2016
license: Beerware - Use this code however you'd like. If you
find it useful you can buy me a beer some time.
Demonstrate basic MPU-9250 functionality including parameterizing the register addresses, initializing the sensor,
getting properly scaled accelerometer, gyroscope, and magnetometer data out. Added display functions to
allow display to on breadboard monitor. Addition of 9 DoF sensor fusion using open source Madgwick and
Mahony filter algorithms. Sketch runs on the 3.3 V 8 MHz Pro Mini and the Teensy 3.1.
This sketch is intended specifically for the MPU9250+MS5637 Add-on shield.
It uses SDA/SCL on pins 21/22, respectively, and it uses the Wire library.
The MS5637 is a simple but high resolution pressure sensor, which can be used in its high resolution
mode but with power consumption of 20 microAmp, or in a lower resolution mode with power consumption of
only 1 microAmp. The choice will depend on the application.
SDA and SCL should have external pull-up resistors (to 3.3V).
4K7 resistors are on the MPU9250+MS5637 breakout board.
Hardware setup:
MPU9250 Breakout --------- ESP32
VDD ---------------------- 3.3V
SDA ----------------------- 21
SCL ----------------------- 22
GND ---------------------- GND
*/
#include "Wire.h"
// See also MPU-9250 Register Map and Descriptions, Revision 4.0, RM-MPU-9250A-00, Rev. 1.4, 9/9/2013 for registers not listed in
// above document; the MPU9250 and MPU9150 are virtually identical but the latter has a different register map
//
//Magnetometer Registers
#define AK8963_ADDRESS 0x0C
#define WHO_AM_I_AK8963 0x00 // should return 0x48
#define INFO 0x01
#define AK8963_ST1 0x02 // data ready status bit 0
#define AK8963_XOUT_L 0x03 // data
#define AK8963_XOUT_H 0x04
#define AK8963_YOUT_L 0x05
#define AK8963_YOUT_H 0x06
#define AK8963_ZOUT_L 0x07
#define AK8963_ZOUT_H 0x08
#define AK8963_ST2 0x09 // Data overflow bit 3 and data read error status bit 2
#define AK8963_CNTL 0x0A // Power down (0000), single-measurement (0001), self-test (1000) and Fuse ROM (1111) modes on bits 3:0
#define AK8963_ASTC 0x0C // Self test control
#define AK8963_I2CDIS 0x0F // I2C disable
#define AK8963_ASAX 0x10 // Fuse ROM x-axis sensitivity adjustment value
#define AK8963_ASAY 0x11 // Fuse ROM y-axis sensitivity adjustment value
#define AK8963_ASAZ 0x12 // Fuse ROM z-axis sensitivity adjustment value
#define SELF_TEST_X_GYRO 0x00
#define SELF_TEST_Y_GYRO 0x01
#define SELF_TEST_Z_GYRO 0x02
/*#define X_FINE_GAIN 0x03 // [7:0] fine gain
#define Y_FINE_GAIN 0x04
#define Z_FINE_GAIN 0x05
#define XA_OFFSET_H 0x06 // User-defined trim values for accelerometer
#define XA_OFFSET_L_TC 0x07
#define YA_OFFSET_H 0x08
#define YA_OFFSET_L_TC 0x09
#define ZA_OFFSET_H 0x0A
#define ZA_OFFSET_L_TC 0x0B */
#define SELF_TEST_X_ACCEL 0x0D
#define SELF_TEST_Y_ACCEL 0x0E
#define SELF_TEST_Z_ACCEL 0x0F
#define SELF_TEST_A 0x10
#define XG_OFFSET_H 0x13 // User-defined trim values for gyroscope
#define XG_OFFSET_L 0x14
#define YG_OFFSET_H 0x15
#define YG_OFFSET_L 0x16
#define ZG_OFFSET_H 0x17
#define ZG_OFFSET_L 0x18
#define SMPLRT_DIV 0x19
#define CONFIG 0x1A
#define GYRO_CONFIG 0x1B
#define ACCEL_CONFIG 0x1C
#define ACCEL_CONFIG2 0x1D
#define LP_ACCEL_ODR 0x1E
#define WOM_THR 0x1F
#define MOT_DUR 0x20 // Duration counter threshold for motion interrupt generation, 1 kHz rate, LSB = 1 ms
#define ZMOT_THR 0x21 // Zero-motion detection threshold bits [7:0]
#define ZRMOT_DUR 0x22 // Duration counter threshold for zero motion interrupt generation, 16 Hz rate, LSB = 64 ms
#define FIFO_EN 0x23
#define I2C_MST_CTRL 0x24
#define I2C_SLV0_ADDR 0x25
#define I2C_SLV0_REG 0x26
#define I2C_SLV0_CTRL 0x27
#define I2C_SLV1_ADDR 0x28
#define I2C_SLV1_REG 0x29
#define I2C_SLV1_CTRL 0x2A
#define I2C_SLV2_ADDR 0x2B
#define I2C_SLV2_REG 0x2C
#define I2C_SLV2_CTRL 0x2D
#define I2C_SLV3_ADDR 0x2E
#define I2C_SLV3_REG 0x2F
#define I2C_SLV3_CTRL 0x30
#define I2C_SLV4_ADDR 0x31
#define I2C_SLV4_REG 0x32
#define I2C_SLV4_DO 0x33
#define I2C_SLV4_CTRL 0x34
#define I2C_SLV4_DI 0x35
#define I2C_MST_STATUS 0x36
#define INT_PIN_CFG 0x37
#define INT_ENABLE 0x38
#define DMP_INT_STATUS 0x39 // Check DMP interrupt
#define INT_STATUS 0x3A
#define ACCEL_XOUT_H 0x3B
#define ACCEL_XOUT_L 0x3C
#define ACCEL_YOUT_H 0x3D
#define ACCEL_YOUT_L 0x3E
#define ACCEL_ZOUT_H 0x3F
#define ACCEL_ZOUT_L 0x40
#define TEMP_OUT_H 0x41
#define TEMP_OUT_L 0x42
#define GYRO_XOUT_H 0x43
#define GYRO_XOUT_L 0x44
#define GYRO_YOUT_H 0x45
#define GYRO_YOUT_L 0x46
#define GYRO_ZOUT_H 0x47
#define GYRO_ZOUT_L 0x48
#define EXT_SENS_DATA_00 0x49
#define EXT_SENS_DATA_01 0x4A
#define EXT_SENS_DATA_02 0x4B
#define EXT_SENS_DATA_03 0x4C
#define EXT_SENS_DATA_04 0x4D
#define EXT_SENS_DATA_05 0x4E
#define EXT_SENS_DATA_06 0x4F
#define EXT_SENS_DATA_07 0x50
#define EXT_SENS_DATA_08 0x51
#define EXT_SENS_DATA_09 0x52
#define EXT_SENS_DATA_10 0x53
#define EXT_SENS_DATA_11 0x54
#define EXT_SENS_DATA_12 0x55
#define EXT_SENS_DATA_13 0x56
#define EXT_SENS_DATA_14 0x57
#define EXT_SENS_DATA_15 0x58
#define EXT_SENS_DATA_16 0x59
#define EXT_SENS_DATA_17 0x5A
#define EXT_SENS_DATA_18 0x5B
#define EXT_SENS_DATA_19 0x5C
#define EXT_SENS_DATA_20 0x5D
#define EXT_SENS_DATA_21 0x5E
#define EXT_SENS_DATA_22 0x5F
#define EXT_SENS_DATA_23 0x60
#define MOT_DETECT_STATUS 0x61
#define I2C_SLV0_DO 0x63
#define I2C_SLV1_DO 0x64
#define I2C_SLV2_DO 0x65
#define I2C_SLV3_DO 0x66
#define I2C_MST_DELAY_CTRL 0x67
#define SIGNAL_PATH_RESET 0x68
#define MOT_DETECT_CTRL 0x69
#define USER_CTRL 0x6A // Bit 7 enable DMP, bit 3 reset DMP
#define PWR_MGMT_1 0x6B // Device defaults to the SLEEP mode
#define PWR_MGMT_2 0x6C
#define DMP_BANK 0x6D // Activates a specific bank in the DMP
#define DMP_RW_PNT 0x6E // Set read/write pointer to a specific start address in specified DMP bank
#define DMP_REG 0x6F // Register in DMP from which to read or to which to write
#define DMP_REG_1 0x70
#define DMP_REG_2 0x71
#define FIFO_COUNTH 0x72
#define FIFO_COUNTL 0x73
#define FIFO_R_W 0x74
#define WHO_AM_I_MPU9250 0x75 // Should return 0x73
#define XA_OFFSET_H 0x77
#define XA_OFFSET_L 0x78
#define YA_OFFSET_H 0x7A
#define YA_OFFSET_L 0x7B
#define ZA_OFFSET_H 0x7D
#define ZA_OFFSET_L 0x7E
// Using the MPU9250_MS5637 Add-On shield, ADO is set to 0
// Seven-bit device address is 110100 for ADO = 0 and 110101 for ADO = 1
#define ADO 0
#if ADO
#define MPU9250_ADDRESS 0x69 // Device address when ADO = 1
#define AK8963_ADDRESS 0x0C // Address of magnetometer
#else
#define MPU9250_ADDRESS 0x68 // Device address when ADO = 0
#define AK8963_ADDRESS 0x0C // Address of magnetometer
#endif
#define SerialDebug true // set to true to get Serial output for debugging
// Set initial input parameters
enum Ascale {
AFS_2G = 0,
AFS_4G,
AFS_8G,
AFS_16G
};
enum Gscale {
GFS_250DPS = 0,
GFS_500DPS,
GFS_1000DPS,
GFS_2000DPS
};
enum Mscale {
MFS_14BITS = 0, // 0.6 mG per LSB
MFS_16BITS // 0.15 mG per LSB
};
#define ADC_256 0x00 // define pressure and temperature conversion rates
#define ADC_512 0x02
#define ADC_1024 0x04
#define ADC_2048 0x06
#define ADC_4096 0x08
#define ADC_8192 0x0A
#define ADC_D1 0x40
#define ADC_D2 0x50
// Specify sensor full scale
uint8_t OSR = ADC_8192; // set pressure amd temperature oversample rate
uint8_t Gscale = GFS_250DPS;
uint8_t Ascale = AFS_2G;
uint8_t Mscale = MFS_16BITS; // Choose either 14-bit or 16-bit magnetometer resolution
uint8_t Mmode = 0x06; // 2 for 8 Hz, 6 for 100 Hz continuous magnetometer data read
float aRes, gRes, mRes; // scale resolutions per LSB for the sensors
// Pin definitions
int intPin = 14; // can be any pin
bool newData = false;
bool newMagData = false;
int myLed = 5;
int16_t MPU9250Data[7]; // used to read all 14 bytes at once from the MPU9250 accel/gyro
int16_t accelCount[3]; // Stores the 16-bit signed accelerometer sensor output
int16_t gyroCount[3]; // Stores the 16-bit signed gyro sensor output
int16_t magCount[3]; // Stores the 16-bit signed magnetometer sensor output
float magCalibration[3] = {0, 0, 0}; // Factory mag calibration and mag bias
float gyroBias[3] = {0, 0, 0}, accelBias[3] = {0, 0, 0}, magBias[3] = {0, 0, 0}, magScale[3] = {0, 0, 0}; // Bias corrections for gyro and accelerometer
int16_t tempCount; // temperature raw count output
float temperature; // Stores the MPU9250 gyro internal chip temperature in degrees Celsius
float SelfTest[6]; // holds results of gyro and accelerometer self test
// global constants for 9 DoF fusion and AHRS (Attitude and Heading Reference System)
float pi = 3.141592653589793238462643383279502884f;
float GyroMeasError = PI * (4.0f / 180.0f); // gyroscope measurement error in rads/s (start at 40 deg/s)
float GyroMeasDrift = PI * (0.0f / 180.0f); // gyroscope measurement drift in rad/s/s (start at 0.0 deg/s/s)
// There is a tradeoff in the beta parameter between accuracy and response speed.
// In the original Madgwick study, beta of 0.041 (corresponding to GyroMeasError of 2.7 degrees/s) was found to give optimal accuracy.
// However, with this value, the LSM9SD0 response time is about 10 seconds to a stable initial quaternion.
// Subsequent changes also require a longish lag time to a stable output, not fast enough for a quadcopter or robot car!
// By increasing beta (GyroMeasError) by about a factor of fifteen, the response time constant is reduced to ~2 sec
// I haven't noticed any reduction in solution accuracy. This is essentially the I coefficient in a PID control sense;
// the bigger the feedback coefficient, the faster the solution converges, usually at the expense of accuracy.
// In any case, this is the free parameter in the Madgwick filtering and fusion scheme.
float beta = sqrt(3.0f / 4.0f) * GyroMeasError; // compute beta
float zeta = sqrt(3.0f / 4.0f) * GyroMeasDrift; // compute zeta, the other free parameter in the Madgwick scheme usually set to a small or zero value
#define Kp 2.0f * 5.0f // these are the free parameters in the Mahony filter and fusion scheme, Kp for proportional feedback, Ki for integral
#define Ki 0.0f
uint32_t delt_t = 0, count = 0, sumCount = 0; // used to control display output rate
float pitch, yaw, roll;
float a12, a22, a31, a32, a33; // rotation matrix coefficients for Euler angles and gravity components
float deltat = 0.0f, sum = 0.0f; // integration interval for both filter schemes
uint32_t lastUpdate = 0, firstUpdate = 0; // used to calculate integration interval
uint32_t Now = 0; // used to calculate integration interval
float ax, ay, az, gx, gy, gz, mx, my, mz; // variables to hold latest sensor data values
float lin_ax, lin_ay, lin_az; // linear acceleration (acceleration with gravity component subtracted)
float q[4] = {1.0f, 0.0f, 0.0f, 0.0f}; // vector to hold quaternion
float eInt[3] = {0.0f, 0.0f, 0.0f}; // vector to hold integral error for Mahony method
void setup()
{
Serial.begin(115200);
delay(4000);
Wire.begin();
Wire.setClock(400000); // two i2c speeds supported: 100kbs or 400kbs
delay(1000);
// Set up the interrupt pin, its set as active high, push-pull
pinMode(intPin, INPUT);
pinMode(myLed, OUTPUT);
digitalWrite(myLed, LOW);
I2Cscan();// look for I2C devices on the bus
// Read the WHO_AM_I register, this is a good test of communication
Serial.println("MPU9250 9-axis motion sensor...");
uint8_t c = readByte(MPU9250_ADDRESS, WHO_AM_I_MPU9250); // Read WHO_AM_I register for MPU-9250
Serial.print("MPU9250 "); Serial.print("I AM "); Serial.print(c, HEX); Serial.print(" I should be "); Serial.println(0x73, HEX);
delay(1000);
if (c == 0x73) // WHO_AM_I should always be 0x73
{
Serial.println("MPU9250 is online...");
MPU9250SelfTest(SelfTest); // Start by performing self test and reporting values
Serial.print("x-axis self test: acceleration trim within : "); Serial.print(SelfTest[0],1); Serial.println("% of factory value");
Serial.print("y-axis self test: acceleration trim within : "); Serial.print(SelfTest[1],1); Serial.println("% of factory value");
Serial.print("z-axis self test: acceleration trim within : "); Serial.print(SelfTest[2],1); Serial.println("% of factory value");
Serial.print("x-axis self test: gyration trim within : "); Serial.print(SelfTest[3],1); Serial.println("% of factory value");
Serial.print("y-axis self test: gyration trim within : "); Serial.print(SelfTest[4],1); Serial.println("% of factory value");
Serial.print("z-axis self test: gyration trim within : "); Serial.print(SelfTest[5],1); Serial.println("% of factory value");
delay(1000);
// get sensor resolutions, only need to do this once
getAres();
getGres();
getMres();
Serial.println(" Calibrate gyro and accel");
accelgyrocalMPU9250(gyroBias, accelBias); // Calibrate gyro and accelerometers, load biases in bias registers
Serial.println("accel biases (mg)"); Serial.println(1000.*accelBias[0]); Serial.println(1000.*accelBias[1]); Serial.println(1000.*accelBias[2]);
Serial.println("gyro biases (dps)"); Serial.println(gyroBias[0]); Serial.println(gyroBias[1]); Serial.println(gyroBias[2]);
delay(1000);
initMPU9250();
Serial.println("MPU9250 initialized for active data mode...."); // Initialize device for active mode read of acclerometer, gyroscope, and temperature
// Read the WHO_AM_I register of the magnetometer, this is a good test of communication
byte d = readByte(AK8963_ADDRESS, WHO_AM_I_AK8963); // Read WHO_AM_I register for AK8963
Serial.print("AK8963 "); Serial.print("I AM "); Serial.print(d, HEX); Serial.print(" I should be "); Serial.println(0x48, HEX);
delay(1000);
// Get magnetometer calibration from AK8963 ROM
initAK8963(magCalibration); Serial.println("AK8963 initialized for active data mode...."); // Initialize device for active mode read of magnetometer
magcalMPU9250(magBias, magScale);
Serial.println("AK8963 mag biases (mG)"); Serial.println(magBias[0]); Serial.println(magBias[1]); Serial.println(magBias[2]);
Serial.println("AK8963 mag scale (mG)"); Serial.println(magScale[0]); Serial.println(magScale[1]); Serial.println(magScale[2]);
delay(2000); // add delay to see results before serial spew of data
if(SerialDebug) {
// Serial.println("Calibration values: ");
Serial.print("X-Axis sensitivity adjustment value "); Serial.println(magCalibration[0], 2);
Serial.print("Y-Axis sensitivity adjustment value "); Serial.println(magCalibration[1], 2);
Serial.print("Z-Axis sensitivity adjustment value "); Serial.println(magCalibration[2], 2);
}
delay(1000);
// attachInterrupt(digitalPinToInterrupt(intPin), myinthandler, RISING); // define interrupt for INT pin output of MPU9250
attachInterrupt(intPin, myinthandler, RISING); // define interrupt for INT pin output of MPU9250
}
else
{
Serial.print("Could not connect to MPU9250: 0x");
Serial.println(c, HEX);
while(1) ; // Loop forever if communication doesn't happen
}
}
void loop()
{
// If intPin goes high, all data registers have new data
if(newData == true) { // On interrupt, read data
newData = false; // reset newData flag
readMPU9250Data(MPU9250Data); // INT cleared on any read
// Now we'll calculate the accleration value into actual g's
ax = (float)MPU9250Data[0]*aRes - accelBias[0]; // get actual g value, this depends on scale being set
ay = (float)MPU9250Data[1]*aRes - accelBias[1];
az = (float)MPU9250Data[2]*aRes - accelBias[2];
// Calculate the gyro value into actual degrees per second
gx = (float)MPU9250Data[4]*gRes; // get actual gyro value, this depends on scale being set
gy = (float)MPU9250Data[5]*gRes;
gz = (float)MPU9250Data[6]*gRes;
newMagData = (readByte(AK8963_ADDRESS, AK8963_ST1) & 0x01);
if(newMagData == true) { // wait for magnetometer data ready bit to be set
readMagData(magCount); // Read the x/y/z adc values
// Calculate the magnetometer values in milliGauss
// Include factory calibration per data sheet and user environmental corrections
mx = (float)magCount[0]*mRes*magCalibration[0] - magBias[0]; // get actual magnetometer value, this depends on scale being set
my = (float)magCount[1]*mRes*magCalibration[1] - magBias[1];
mz = (float)magCount[2]*mRes*magCalibration[2] - magBias[2];
mx *= magScale[0];
my *= magScale[1];
mz *= magScale[2];
}
for(uint8_t i = 0; i < 10; i++) { // iterate a fixed number of times per data read cycle
Now = micros();
deltat = ((Now - lastUpdate)/1000000.0f); // set integration time by time elapsed since last filter update
lastUpdate = Now;
sum += deltat; // sum for averaging filter update rate
sumCount++;
MadgwickQuaternionUpdate(-ax, ay, az, gx*pi/180.0f, -gy*pi/180.0f, -gz*pi/180.0f, my, -mx, mz);
}
}
// Serial print and/or display at 0.5 s rate independent of data rates
delt_t = millis() - count;
if (delt_t > 500) { // update LCD once per half-second independent of read rate
if(SerialDebug) {
// Serial.print("ax = "); Serial.print((int)1000*ax);
// Serial.print(" ay = "); Serial.print((int)1000*ay);
// Serial.print(" az = "); Serial.print((int)1000*az); Serial.println(" mg");
// Serial.print("gx = "); Serial.print( gx, 2);
// Serial.print(" gy = "); Serial.print( gy, 2);
// Serial.print(" gz = "); Serial.print( gz, 2); Serial.println(" deg/s");
// Serial.print("mx = "); Serial.print( (int)mx );
// Serial.print(" my = "); Serial.print( (int)my );
// Serial.print(" mz = "); Serial.print( (int)mz ); Serial.println(" mG");
Serial.print("q0 = "); Serial.print(q[0]);
Serial.print(" qx = "); Serial.print(q[1]);
Serial.print(" qy = "); Serial.print(q[2]);
Serial.print(" qz = "); Serial.println(q[3]);
}
tempCount = readTempData(); // Read the gyro adc values
temperature = ((float) tempCount) / 333.87f + 21.0f; // Gyro chip temperature in degrees Centigrade
// Print temperature in degrees Centigrade
Serial.print("Gyro temperature is "); Serial.print(temperature, 1); Serial.println(" degrees C"); // Print T values to tenths of s degree C
// Define output variables from updated quaternion---these are Tait-Bryan angles, commonly used in aircraft orientation.
// In this coordinate system, the positive z-axis is down toward Earth.
// Yaw is the angle between Sensor x-axis and Earth magnetic North (or true North if corrected for local declination, looking down on the sensor positive yaw is counterclockwise.
// Pitch is angle between sensor x-axis and Earth ground plane, toward the Earth is positive, up toward the sky is negative.
// Roll is angle between sensor y-axis and Earth ground plane, y-axis up is positive roll.
// These arise from the definition of the homogeneous rotation matrix constructed from quaternions.
// Tait-Bryan angles as well as Euler angles are non-commutative; that is, the get the correct orientation the rotations must be
// applied in the correct order which for this configuration is yaw, pitch, and then roll.
// For more see http://en.wikipedia.org/wiki/Conversion_between_quaternions_and_Euler_angles which has additional links.
//Software AHRS:
// yaw = atan2f(2.0f * (q[1] * q[2] + q[0] * q[3]), q[0] * q[0] + q[1] * q[1] - q[2] * q[2] - q[3] * q[3]);
// pitch = -asinf(2.0f * (q[1] * q[3] - q[0] * q[2]));
// roll = atan2f(2.0f * (q[0] * q[1] + q[2] * q[3]), q[0] * q[0] - q[1] * q[1] - q[2] * q[2] + q[3] * q[3]);
// pitch *= 180.0f / PI;
// yaw *= 180.0f / PI;
// yaw += 13.8f; // Declination at Danville, California is 13 degrees 48 minutes and 47 seconds on 2014-04-04
// if(yaw < 0) yaw += 360.0f; // Ensure yaw stays between 0 and 360
// roll *= 180.0f / PI;
a12 = 2.0f * (q[1] * q[2] + q[0] * q[3]);
a22 = q[0] * q[0] + q[1] * q[1] - q[2] * q[2] - q[3] * q[3];
a31 = 2.0f * (q[0] * q[1] + q[2] * q[3]);
a32 = 2.0f * (q[1] * q[3] - q[0] * q[2]);
a33 = q[0] * q[0] - q[1] * q[1] - q[2] * q[2] + q[3] * q[3];
pitch = -asin(a32);
roll = atan2(a31, a33);
yaw = atan2(a12, a22);
pitch *= 180.0f / pi;
yaw *= 180.0f / pi;
yaw += 13.8f; // Declination at Danville, California is 13 degrees 48 minutes and 47 seconds on 2014-04-04
if(yaw < 0) yaw += 360.0f; // Ensure yaw stays between 0 and 360
roll *= 180.0f / pi;
lin_ax = ax + a31;
lin_ay = ay + a32;
lin_az = az - a33;
if(SerialDebug) {
Serial.print("Yaw, Pitch, Roll: ");
Serial.print(yaw, 2);
Serial.print(", ");
Serial.print(pitch, 2);
Serial.print(", ");
Serial.println(roll, 2);
Serial.print("Grav_x, Grav_y, Grav_z: ");
Serial.print(-a31*1000.0f, 2);
Serial.print(", ");
Serial.print(-a32*1000.0f, 2);
Serial.print(", ");
Serial.print(a33*1000.0f, 2); Serial.println(" mg");
Serial.print("Lin_ax, Lin_ay, Lin_az: ");
Serial.print(lin_ax*1000.0f, 2);
Serial.print(", ");
Serial.print(lin_ay*1000.0f, 2);
Serial.print(", ");
Serial.print(lin_az*1000.0f, 2); Serial.println(" mg");
Serial.print("sumCount = "); Serial.println(sumCount);
Serial.print("sum = "); Serial.println(sum);
Serial.print("rate = "); Serial.print((float)sumCount/sum, 2); Serial.println(" Hz");
}
digitalWrite(myLed, !digitalRead(myLed));
count = millis();
sumCount = 0;
sum = 0;
}
}
//===================================================================================================================
//====== Set of useful function to access acceleration. gyroscope, magnetometer, and temperature data
//===================================================================================================================
void myinthandler()
{
newData = true;
}
void getMres() {
switch (Mscale)
{
// Possible magnetometer scales (and their register bit settings) are:
// 14 bit resolution (0) and 16 bit resolution (1)
case MFS_14BITS:
mRes = 10.*4912./8190.; // Proper scale to return milliGauss
break;
case MFS_16BITS:
mRes = 10.*4912./32760.0; // Proper scale to return milliGauss
break;
}
}
void getGres() {
switch (Gscale)
{
// Possible gyro scales (and their register bit settings) are:
// 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS (11).
// Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:
case GFS_250DPS:
gRes = 250.0/32768.0;
break;
case GFS_500DPS:
gRes = 500.0/32768.0;
break;
case GFS_1000DPS:
gRes = 1000.0/32768.0;
break;
case GFS_2000DPS:
gRes = 2000.0/32768.0;
break;
}
}
void getAres() {
switch (Ascale)
{
// Possible accelerometer scales (and their register bit settings) are:
// 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs (11).
// Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:
case AFS_2G:
aRes = 2.0/32768.0;
break;
case AFS_4G:
aRes = 4.0/32768.0;
break;
case AFS_8G:
aRes = 8.0/32768.0;
break;
case AFS_16G:
aRes = 16.0/32768.0;
break;
}
}
void readMPU9250Data(int16_t * destination)
{
uint8_t rawData[14]; // x/y/z accel register data stored here
readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 14, &rawData[0]); // Read the 14 raw data registers into data array
destination[0] = ((int16_t)rawData[0] << 8) | rawData[1] ; // Turn the MSB and LSB into a signed 16-bit value
destination[1] = ((int16_t)rawData[2] << 8) | rawData[3] ;
destination[2] = ((int16_t)rawData[4] << 8) | rawData[5] ;
destination[3] = ((int16_t)rawData[6] << 8) | rawData[7] ;
destination[4] = ((int16_t)rawData[8] << 8) | rawData[9] ;
destination[5] = ((int16_t)rawData[10] << 8) | rawData[11] ;
destination[6] = ((int16_t)rawData[12] << 8) | rawData[13] ;
}
void readAccelData(int16_t * destination)
{
uint8_t rawData[6]; // x/y/z accel register data stored here
readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
destination[0] = ((int16_t)rawData[0] << 8) | rawData[1] ; // Turn the MSB and LSB into a signed 16-bit value
destination[1] = ((int16_t)rawData[2] << 8) | rawData[3] ;
destination[2] = ((int16_t)rawData[4] << 8) | rawData[5] ;
}
void readGyroData(int16_t * destination)
{
uint8_t rawData[6]; // x/y/z gyro register data stored here
readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
destination[0] = ((int16_t)rawData[0] << 8) | rawData[1] ; // Turn the MSB and LSB into a signed 16-bit value
destination[1] = ((int16_t)rawData[2] << 8) | rawData[3] ;
destination[2] = ((int16_t)rawData[4] << 8) | rawData[5] ;
}
void readMagData(int16_t * destination)
{
uint8_t rawData[7]; // x/y/z gyro register data, ST2 register stored here, must read ST2 at end of data acquisition
readBytes(AK8963_ADDRESS, AK8963_XOUT_L, 7, &rawData[0]); // Read the six raw data and ST2 registers sequentially into data array
uint8_t c = rawData[6]; // End data read by reading ST2 register
if(!(c & 0x08)) { // Check if magnetic sensor overflow set, if not then report data
destination[0] = ((int16_t)rawData[1] << 8) | rawData[0] ; // Turn the MSB and LSB into a signed 16-bit value
destination[1] = ((int16_t)rawData[3] << 8) | rawData[2] ; // Data stored as little Endian
destination[2] = ((int16_t)rawData[5] << 8) | rawData[4] ;
}
}
int16_t readTempData()
{
uint8_t rawData[2]; // x/y/z gyro register data stored here
readBytes(MPU9250_ADDRESS, TEMP_OUT_H, 2, &rawData[0]); // Read the two raw data registers sequentially into data array
return ((int16_t)rawData[0] << 8) | rawData[1] ; // Turn the MSB and LSB into a 16-bit value
}
void initAK8963(float * destination)
{
// First extract the factory calibration for each magnetometer axis
uint8_t rawData[3]; // x/y/z gyro calibration data stored here
writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x00); // Power down magnetometer
delay(10);
writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x0F); // Enter Fuse ROM access mode
delay(10);
readBytes(AK8963_ADDRESS, AK8963_ASAX, 3, &rawData[0]); // Read the x-, y-, and z-axis calibration values
destination[0] = (float)(rawData[0] - 128)/256. + 1.; // Return x-axis sensitivity adjustment values, etc.
destination[1] = (float)(rawData[1] - 128)/256. + 1.;
destination[2] = (float)(rawData[2] - 128)/256. + 1.;
writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x00); // Power down magnetometer
delay(10);
// Configure the magnetometer for continuous read and highest resolution
// set Mscale bit 4 to 1 (0) to enable 16 (14) bit resolution in CNTL register,
// and enable continuous mode data acquisition Mmode (bits [3:0]), 0010 for 8 Hz and 0110 for 100 Hz sample rates
writeByte(AK8963_ADDRESS, AK8963_CNTL, Mscale << 4 | Mmode); // Set magnetometer data resolution and sample ODR
delay(10);
}
void initMPU9250()
{
// wake up device
writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors
delay(100); // Wait for all registers to reset
// get stable time source
writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x01); // Auto select clock source to be PLL gyroscope reference if ready else
delay(200);
// Configure Gyro and Thermometer
// Disable FSYNC and set thermometer and gyro bandwidth to 41 and 42 Hz, respectively;
// minimum delay time for this setting is 5.9 ms, which means sensor fusion update rates cannot
// be higher than 1 / 0.0059 = 170 Hz
// DLPF_CFG = bits 2:0 = 011; this limits the sample rate to 1000 Hz for both
// With the MPU9250, it is possible to get gyro sample rates of 32 kHz (!), 8 kHz, or 1 kHz
writeByte(MPU9250_ADDRESS, CONFIG, 0x03);
// Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV)
writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x04); // Use a 200 Hz rate; a rate consistent with the filter update rate
// determined inset in CONFIG above
// Set gyroscope full scale range
// Range selects FS_SEL and GFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3
uint8_t c = readByte(MPU9250_ADDRESS, GYRO_CONFIG); // get current GYRO_CONFIG register value
// c = c & ~0xE0; // Clear self-test bits [7:5]
c = c & ~0x03; // Clear Fchoice bits [1:0]
c = c & ~0x18; // Clear GFS bits [4:3]
c = c | Gscale << 3; // Set full scale range for the gyro
// c =| 0x00; // Set Fchoice for the gyro to 11 by writing its inverse to bits 1:0 of GYRO_CONFIG
writeByte(MPU9250_ADDRESS, GYRO_CONFIG, c ); // Write new GYRO_CONFIG value to register
// Set accelerometer full-scale range configuration
c = readByte(MPU9250_ADDRESS, ACCEL_CONFIG); // get current ACCEL_CONFIG register value
// c = c & ~0xE0; // Clear self-test bits [7:5]
c = c & ~0x18; // Clear AFS bits [4:3]
c = c | Ascale << 3; // Set full scale range for the accelerometer
writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, c); // Write new ACCEL_CONFIG register value
// Set accelerometer sample rate configuration
// It is possible to get a 4 kHz sample rate from the accelerometer by choosing 1 for
// accel_fchoice_b bit [3]; in this case the bandwidth is 1.13 kHz
c = readByte(MPU9250_ADDRESS, ACCEL_CONFIG2); // get current ACCEL_CONFIG2 register value
c = c & ~0x0F; // Clear accel_fchoice_b (bit 3) and A_DLPFG (bits [2:0])
c = c | 0x03; // Set accelerometer rate to 1 kHz and bandwidth to 41 Hz
writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, c); // Write new ACCEL_CONFIG2 register value
// The accelerometer, gyro, and thermometer are set to 1 kHz sample rates,
// but all these rates are further reduced by a factor of 5 to 200 Hz because of the SMPLRT_DIV setting
// Configure Interrupts and Bypass Enable
// Set interrupt pin active high, push-pull, hold interrupt pin level HIGH until interrupt cleared,
// clear on read of INT_STATUS, and enable I2C_BYPASS_EN so additional chips
// can join the I2C bus and all can be controlled by the Arduino as master
// writeByte(MPU9250_ADDRESS, INT_PIN_CFG, 0x22);
writeByte(MPU9250_ADDRESS, INT_PIN_CFG, 0x12); // INT is 50 microsecond pulse and any read to clear
writeByte(MPU9250_ADDRESS, INT_ENABLE, 0x01); // Enable data ready (bit 0) interrupt
delay(100);
}
// Function which accumulates gyro and accelerometer data after device initialization. It calculates the average
// of the at-rest readings and then loads the resulting offsets into accelerometer and gyro bias registers.
void accelgyrocalMPU9250(float * dest1, float * dest2)
{
uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data
uint16_t ii, packet_count, fifo_count;
int32_t gyro_bias[3] = {0, 0, 0}, accel_bias[3] = {0, 0, 0};
// reset device
writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device
delay(100);
// get stable time source; Auto select clock source to be PLL gyroscope reference if ready
// else use the internal oscillator, bits 2:0 = 001
writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x01);
writeByte(MPU9250_ADDRESS, PWR_MGMT_2, 0x00);
delay(200);
// Configure device for bias calculation
writeByte(MPU9250_ADDRESS, INT_ENABLE, 0x00); // Disable all interrupts
writeByte(MPU9250_ADDRESS, FIFO_EN, 0x00); // Disable FIFO
writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x00); // Turn on internal clock source
writeByte(MPU9250_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master
writeByte(MPU9250_ADDRESS, USER_CTRL, 0x00); // Disable FIFO and I2C master modes
writeByte(MPU9250_ADDRESS, USER_CTRL, 0x0C); // Reset FIFO and DMP
delay(15);
// Configure MPU6050 gyro and accelerometer for bias calculation
writeByte(MPU9250_ADDRESS, CONFIG, 0x01); // Set low-pass filter to 188 Hz
writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set sample rate to 1 kHz
writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0x00); // Set gyro full-scale to 250 degrees per second, maximum sensitivity
writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity
uint16_t gyrosensitivity = 131; // = 131 LSB/degrees/sec
uint16_t accelsensitivity = 16384; // = 16384 LSB/g
// Configure FIFO to capture accelerometer and gyro data for bias calculation
writeByte(MPU9250_ADDRESS, USER_CTRL, 0x40); // Enable FIFO
writeByte(MPU9250_ADDRESS, FIFO_EN, 0x78); // Enable gyro and accelerometer sensors for FIFO (max size 512 bytes in MPU-9150)
delay(40); // accumulate 40 samples in 40 milliseconds = 480 bytes
// At end of sample accumulation, turn off FIFO sensor read
writeByte(MPU9250_ADDRESS, FIFO_EN, 0x00); // Disable gyro and accelerometer sensors for FIFO
readBytes(MPU9250_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count
fifo_count = ((uint16_t)data[0] << 8) | data[1];
packet_count = fifo_count/12;// How many sets of full gyro and accelerometer data for averaging
for (ii = 0; ii < packet_count; ii++) {
int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0};
readBytes(MPU9250_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging
accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1] ) ; // Form signed 16-bit integer for each sample in FIFO
accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3] ) ;
accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5] ) ;
gyro_temp[0] = (int16_t) (((int16_t)data[6] << 8) | data[7] ) ;
gyro_temp[1] = (int16_t) (((int16_t)data[8] << 8) | data[9] ) ;
gyro_temp[2] = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;
accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases
accel_bias[1] += (int32_t) accel_temp[1];
accel_bias[2] += (int32_t) accel_temp[2];
gyro_bias[0] += (int32_t) gyro_temp[0];
gyro_bias[1] += (int32_t) gyro_temp[1];
gyro_bias[2] += (int32_t) gyro_temp[2];
}
accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases
accel_bias[1] /= (int32_t) packet_count;
accel_bias[2] /= (int32_t) packet_count;
gyro_bias[0] /= (int32_t) packet_count;
gyro_bias[1] /= (int32_t) packet_count;
gyro_bias[2] /= (int32_t) packet_count;
if(accel_bias[2] > 0L) {accel_bias[2] -= (int32_t) accelsensitivity;} // Remove gravity from the z-axis accelerometer bias calculation
else {accel_bias[2] += (int32_t) accelsensitivity;}
// Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup
data[0] = (-gyro_bias[0]/4 >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format
data[1] = (-gyro_bias[0]/4) & 0xFF; // Biases are additive, so change sign on calculated average gyro biases
data[2] = (-gyro_bias[1]/4 >> 8) & 0xFF;
data[3] = (-gyro_bias[1]/4) & 0xFF;
data[4] = (-gyro_bias[2]/4 >> 8) & 0xFF;
data[5] = (-gyro_bias[2]/4) & 0xFF;
// Push gyro biases to hardware registers
writeByte(MPU9250_ADDRESS, XG_OFFSET_H, data[0]);
writeByte(MPU9250_ADDRESS, XG_OFFSET_L, data[1]);
writeByte(MPU9250_ADDRESS, YG_OFFSET_H, data[2]);
writeByte(MPU9250_ADDRESS, YG_OFFSET_L, data[3]);
writeByte(MPU9250_ADDRESS, ZG_OFFSET_H, data[4]);
writeByte(MPU9250_ADDRESS, ZG_OFFSET_L, data[5]);
// Output scaled gyro biases for display in the main program
dest1[0] = (float) gyro_bias[0]/(float) gyrosensitivity;
dest1[1] = (float) gyro_bias[1]/(float) gyrosensitivity;
dest1[2] = (float) gyro_bias[2]/(float) gyrosensitivity;
// Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain
// factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold
// non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature
// compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that
// the accelerometer biases calculated above must be divided by 8.
int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases
readBytes(MPU9250_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values
accel_bias_reg[0] = (int32_t) (((int16_t)data[0] << 8) | data[1]);
readBytes(MPU9250_ADDRESS, YA_OFFSET_H, 2, &data[0]);
accel_bias_reg[1] = (int32_t) (((int16_t)data[0] << 8) | data[1]);
readBytes(MPU9250_ADDRESS, ZA_OFFSET_H, 2, &data[0]);
accel_bias_reg[2] = (int32_t) (((int16_t)data[0] << 8) | data[1]);
uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers
uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis
for(ii = 0; ii < 3; ii++) {
if((accel_bias_reg[ii] & mask)) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit
}
// Construct total accelerometer bias, including calculated average accelerometer bias from above
accel_bias_reg[0] -= (accel_bias[0]/8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale)
accel_bias_reg[1] -= (accel_bias[1]/8);
accel_bias_reg[2] -= (accel_bias[2]/8);
data[0] = (accel_bias_reg[0] >> 8) & 0xFF;
data[1] = (accel_bias_reg[0]) & 0xFF;
data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers
data[2] = (accel_bias_reg[1] >> 8) & 0xFF;
data[3] = (accel_bias_reg[1]) & 0xFF;
data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers
data[4] = (accel_bias_reg[2] >> 8) & 0xFF;
data[5] = (accel_bias_reg[2]) & 0xFF;
data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers
// Apparently this is not working for the acceleration biases in the MPU-9250
// Are we handling the temperature correction bit properly?
// Push accelerometer biases to hardware registers
/* writeByte(MPU9250_ADDRESS, XA_OFFSET_H, data[0]);
writeByte(MPU9250_ADDRESS, XA_OFFSET_L, data[1]);
writeByte(MPU9250_ADDRESS, YA_OFFSET_H, data[2]);
writeByte(MPU9250_ADDRESS, YA_OFFSET_L, data[3]);
writeByte(MPU9250_ADDRESS, ZA_OFFSET_H, data[4]);
writeByte(MPU9250_ADDRESS, ZA_OFFSET_L, data[5]);
*/
// Output scaled accelerometer biases for display in the main program
dest2[0] = (float)accel_bias[0]/(float)accelsensitivity;
dest2[1] = (float)accel_bias[1]/(float)accelsensitivity;
dest2[2] = (float)accel_bias[2]/(float)accelsensitivity;
}
void magcalMPU9250(float * dest1, float * dest2)
{
uint16_t ii = 0, sample_count = 0;
int32_t mag_bias[3] = {0, 0, 0}, mag_scale[3] = {0, 0, 0};
int16_t mag_max[3] = {-32767, -32767, -32767}, mag_min[3] = {32767, 32767, 32767}, mag_temp[3] = {0, 0, 0};
Serial.println("Mag Calibration: Wave device in a figure eight until done!");
delay(4000);
// shoot for ~fifteen seconds of mag data
if(Mmode == 0x02) sample_count = 128; // at 8 Hz ODR, new mag data is available every 125 ms
if(Mmode == 0x06) sample_count = 1500; // at 100 Hz ODR, new mag data is available every 10 ms
for(ii = 0; ii < sample_count; ii++) {
readMagData(mag_temp); // Read the mag data
for (int jj = 0; jj < 3; jj++) {
if(mag_temp[jj] > mag_max[jj]) mag_max[jj] = mag_temp[jj];
if(mag_temp[jj] < mag_min[jj]) mag_min[jj] = mag_temp[jj];
}
if(Mmode == 0x02) delay(135); // at 8 Hz ODR, new mag data is available every 125 ms
if(Mmode == 0x06) delay(12); // at 100 Hz ODR, new mag data is available every 10 ms
}
// Serial.println("mag x min/max:"); Serial.println(mag_max[0]); Serial.println(mag_min[0]);
// Serial.println("mag y min/max:"); Serial.println(mag_max[1]); Serial.println(mag_min[1]);
// Serial.println("mag z min/max:"); Serial.println(mag_max[2]); Serial.println(mag_min[2]);
// Get hard iron correction
mag_bias[0] = (mag_max[0] + mag_min[0])/2; // get average x mag bias in counts
mag_bias[1] = (mag_max[1] + mag_min[1])/2; // get average y mag bias in counts
mag_bias[2] = (mag_max[2] + mag_min[2])/2; // get average z mag bias in counts
dest1[0] = (float) mag_bias[0]*mRes*magCalibration[0]; // save mag biases in G for main program
dest1[1] = (float) mag_bias[1]*mRes*magCalibration[1];
dest1[2] = (float) mag_bias[2]*mRes*magCalibration[2];
// Get soft iron correction estimate
mag_scale[0] = (mag_max[0] - mag_min[0])/2; // get average x axis max chord length in counts
mag_scale[1] = (mag_max[1] - mag_min[1])/2; // get average y axis max chord length in counts
mag_scale[2] = (mag_max[2] - mag_min[2])/2; // get average z axis max chord length in counts
float avg_rad = mag_scale[0] + mag_scale[1] + mag_scale[2];
avg_rad /= 3.0;
dest2[0] = avg_rad/((float)mag_scale[0]);
dest2[1] = avg_rad/((float)mag_scale[1]);
dest2[2] = avg_rad/((float)mag_scale[2]);
Serial.println("Mag Calibration done!");
}
// Accelerometer and gyroscope self test; check calibration wrt factory settings
void MPU9250SelfTest(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass
{
uint8_t rawData[6] = {0, 0, 0, 0, 0, 0};
uint8_t selfTest[6];
int32_t gAvg[3] = {0}, aAvg[3] = {0}, aSTAvg[3] = {0}, gSTAvg[3] = {0};
float factoryTrim[6];
uint8_t FS = 0;
writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set gyro sample rate to 1 kHz
writeByte(MPU9250_ADDRESS, CONFIG, 0x02); // Set gyro sample rate to 1 kHz and DLPF to 92 Hz
writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 1<<FS); // Set full scale range for the gyro to 250 dps
writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, 0x02); // Set accelerometer rate to 1 kHz and bandwidth to 92 Hz
writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 1<<FS); // Set full scale range for the accelerometer to 2 g
for( int ii = 0; ii < 200; ii++) { // get average current values of gyro and acclerometer
readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
aAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
aAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
aAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
gAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
gAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
gAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
}
for (int ii =0; ii < 3; ii++) { // Get average of 200 values and store as average current readings
aAvg[ii] /= 200;
gAvg[ii] /= 200;
}
// Configure the accelerometer for self-test
writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0xE0); // Enable self test on all three axes and set accelerometer range to +/- 2 g
writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s
delay(25); // Delay a while to let the device stabilize
for( int ii = 0; ii < 200; ii++) { // get average self-test values of gyro and acclerometer
readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
aSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
aSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
aSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
gSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
gSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
gSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
}
for (int ii =0; ii < 3; ii++) { // Get average of 200 values and store as average self-test readings
aSTAvg[ii] /= 200;
gSTAvg[ii] /= 200;
}
// Configure the gyro and accelerometer for normal operation
writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0x00);
writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0x00);
delay(25); // Delay a while to let the device stabilize
// Retrieve accelerometer and gyro factory Self-Test Code from USR_Reg
selfTest[0] = readByte(MPU9250_ADDRESS, SELF_TEST_X_ACCEL); // X-axis accel self-test results
selfTest[1] = readByte(MPU9250_ADDRESS, SELF_TEST_Y_ACCEL); // Y-axis accel self-test results
selfTest[2] = readByte(MPU9250_ADDRESS, SELF_TEST_Z_ACCEL); // Z-axis accel self-test results
selfTest[3] = readByte(MPU9250_ADDRESS, SELF_TEST_X_GYRO); // X-axis gyro self-test results
selfTest[4] = readByte(MPU9250_ADDRESS, SELF_TEST_Y_GYRO); // Y-axis gyro self-test results
selfTest[5] = readByte(MPU9250_ADDRESS, SELF_TEST_Z_GYRO); // Z-axis gyro self-test results
// Retrieve factory self-test value from self-test code reads
factoryTrim[0] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[0] - 1.0) )); // FT[Xa] factory trim calculation
factoryTrim[1] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[1] - 1.0) )); // FT[Ya] factory trim calculation
factoryTrim[2] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[2] - 1.0) )); // FT[Za] factory trim calculation
factoryTrim[3] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[3] - 1.0) )); // FT[Xg] factory trim calculation
factoryTrim[4] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[4] - 1.0) )); // FT[Yg] factory trim calculation
factoryTrim[5] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[5] - 1.0) )); // FT[Zg] factory trim calculation
// Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response
// To get percent, must multiply by 100
for (int i = 0; i < 3; i++) {
destination[i] = 100.0f*((float)(aSTAvg[i] - aAvg[i]))/factoryTrim[i] - 100.0f; // Report percent differences
destination[i+3] = 100.0f*((float)(gSTAvg[i] - gAvg[i]))/factoryTrim[i+3] - 100.0f; // Report percent differences
}
}
// simple function to scan for I2C devices on the bus
void I2Cscan()
{
// scan for i2c devices
byte error, address;
int nDevices;
Serial.println("Scanning...");
nDevices = 0;
for(address = 1; address < 127; address++ )
{
// The i2c_scanner uses the return value of
// the Write.endTransmisstion to see if
// a device did acknowledge to the address.
Wire.beginTransmission(address);
error = Wire.endTransmission();
if (error == 0)
{
Serial.print("I2C device found at address 0x");
if (address<16)
Serial.print("0");
Serial.print(address,HEX);
Serial.println(" !");
nDevices++;
}
else if (error==4)
{
Serial.print("Unknown error at address 0x");
if (address<16)
Serial.print("0");
Serial.println(address,HEX);
}
}
if (nDevices == 0)
Serial.println("No I2C devices found\n");
else
Serial.println("done\n");
}
// I2C read/write functions for the MPU9250 sensors
void writeByte(uint8_t address, uint8_t subAddress, uint8_t data)
{
Wire.beginTransmission(address); // Initialize the Tx buffer
Wire.write(subAddress); // Put slave register address in Tx buffer
Wire.write(data); // Put data in Tx buffer
Wire.endTransmission(); // Send the Tx buffer
}
uint8_t readByte(uint8_t address, uint8_t subAddress)
{
uint8_t data = 0; // `data` will store the register data
Wire.beginTransmission(address); // Initialize the Tx buffer
Wire.write(subAddress); // Put slave register address in Tx buffer
Wire.endTransmission(false); // Send the Tx buffer, but send a restart to keep connection alive
Wire.requestFrom(address, 1); // Read two bytes from slave register address on MPU9250
data = Wire.read(); // Fill Rx buffer with result
return data; // Return data read from slave register
}
void readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest)
{
Wire.beginTransmission(address); // Initialize the Tx buffer
Wire.write(subAddress); // Put slave register address in Tx buffer
Wire.endTransmission(false); // Send the Tx buffer, but send a restart to keep connection alive
uint8_t i = 0;
Wire.requestFrom(address, count); // Read bytes from slave register address
while (Wire.available()) {
dest[i++] = Wire.read(); } // Put read results in the Rx buffer
}
The sketch is designed to throttle the sensor fusion rate since the MCU is so fast. In other words, it is designed to provide ten iterations of the sensor fusion filter for every new gyro data set.
for(uint8_t i = 0; i < 10; i++) { // iterate a fixed number of times per data read cycle Now = micros(); deltat = ((Now - lastUpdate)/1000000.0f); // set integration time by time elapsed since last filter update lastUpdate = Now;
sum += deltat; // sum for averaging filter update rate
sumCount++;
MadgwickQuaternionUpdate(-ax, ay, az, gx*pi/180.0f, -gy*pi/180.0f,
-gz*pi/180.0f, my, -mx, mz); }
Since the gyro data rate is 200 Hz, the filter rate will be 10 x 200 Hz = 2 kHz, as you see.
If you want to use a faster fusion rate, this really means more iterations. So change the ten in the above loop to 20, 30, or even 50 and see what you get. There will be a limit.
I would set the gyro/accel rate to 500 Hz or 1 kHz and experiment with 10, 20, 30, etc iterations to see if you can get what you want. In my experience 20 is plenty, but YMMV.
On Mon, Oct 21, 2019 at 11:09 PM shomedas notifications@github.com wrote:
I am attaching herewith your original code from link https://github.com/kriswiner/ESP32/tree/master/MPU9250_MS5637 without the 5637 part. if you can spare some time please check if you get >> 2KHz fusion rate.
/* MPU9250_MS5637_ESP32 Basic Example Code by: Kris Winer date: December 14, 2016 license: Beerware - Use this code however you'd like. If you find it useful you can buy me a beer some time.
Demonstrate basic MPU-9250 functionality including parameterizing the register addresses, initializing the sensor, getting properly scaled accelerometer, gyroscope, and magnetometer data out. Added display functions to allow display to on breadboard monitor. Addition of 9 DoF sensor fusion using open source Madgwick and Mahony filter algorithms. Sketch runs on the 3.3 V 8 MHz Pro Mini and the Teensy 3.1.
This sketch is intended specifically for the MPU9250+MS5637 Add-on shield. It uses SDA/SCL on pins 21/22, respectively, and it uses the Wire library. The MS5637 is a simple but high resolution pressure sensor, which can be used in its high resolution mode but with power consumption of 20 microAmp, or in a lower resolution mode with power consumption of only 1 microAmp. The choice will depend on the application.
SDA and SCL should have external pull-up resistors (to 3.3V). 4K7 resistors are on the MPU9250+MS5637 breakout board.
Hardware setup: MPU9250 Breakout --------- ESP32 VDD ---------------------- 3.3V SDA ----------------------- 21 SCL ----------------------- 22 GND ---------------------- GND
*/
include "Wire.h"
// See also MPU-9250 Register Map and Descriptions, Revision 4.0, RM-MPU-9250A-00, Rev. 1.4, 9/9/2013 for registers not listed in // above document; the MPU9250 and MPU9150 are virtually identical but the latter has a different register map // //Magnetometer Registers
define AK8963_ADDRESS 0x0C
define WHO_AM_I_AK8963 0x00 // should return 0x48
define INFO 0x01
define AK8963_ST1 0x02 // data ready status bit 0
define AK8963_XOUT_L 0x03 // data
define AK8963_XOUT_H 0x04
define AK8963_YOUT_L 0x05
define AK8963_YOUT_H 0x06
define AK8963_ZOUT_L 0x07
define AK8963_ZOUT_H 0x08
define AK8963_ST2 0x09 // Data overflow bit 3 and data read error status bit 2
define AK8963_CNTL 0x0A // Power down (0000), single-measurement (0001), self-test (1000) and Fuse ROM (1111) modes on bits 3:0
define AK8963_ASTC 0x0C // Self test control
define AK8963_I2CDIS 0x0F // I2C disable
define AK8963_ASAX 0x10 // Fuse ROM x-axis sensitivity adjustment value
define AK8963_ASAY 0x11 // Fuse ROM y-axis sensitivity adjustment value
define AK8963_ASAZ 0x12 // Fuse ROM z-axis sensitivity adjustment value
define SELF_TEST_X_GYRO 0x00
define SELF_TEST_Y_GYRO 0x01
define SELF_TEST_Z_GYRO 0x02
/*#define X_FINE_GAIN 0x03 // [7:0] fine gain
define Y_FINE_GAIN 0x04
define Z_FINE_GAIN 0x05
define XA_OFFSET_H 0x06 // User-defined trim values for accelerometer
define XA_OFFSET_L_TC 0x07
define YA_OFFSET_H 0x08
define YA_OFFSET_L_TC 0x09
define ZA_OFFSET_H 0x0A
define ZA_OFFSET_L_TC 0x0B */
define SELF_TEST_X_ACCEL 0x0D
define SELF_TEST_Y_ACCEL 0x0E
define SELF_TEST_Z_ACCEL 0x0F
define SELF_TEST_A 0x10
define XG_OFFSET_H 0x13 // User-defined trim values for gyroscope
define XG_OFFSET_L 0x14
define YG_OFFSET_H 0x15
define YG_OFFSET_L 0x16
define ZG_OFFSET_H 0x17
define ZG_OFFSET_L 0x18
define SMPLRT_DIV 0x19
define CONFIG 0x1A
define GYRO_CONFIG 0x1B
define ACCEL_CONFIG 0x1C
define ACCEL_CONFIG2 0x1D
define LP_ACCEL_ODR 0x1E
define WOM_THR 0x1F
define MOT_DUR 0x20 // Duration counter threshold for motion interrupt generation, 1 kHz rate, LSB = 1 ms
define ZMOT_THR 0x21 // Zero-motion detection threshold bits [7:0]
define ZRMOT_DUR 0x22 // Duration counter threshold for zero motion interrupt generation, 16 Hz rate, LSB = 64 ms
define FIFO_EN 0x23
define I2C_MST_CTRL 0x24
define I2C_SLV0_ADDR 0x25
define I2C_SLV0_REG 0x26
define I2C_SLV0_CTRL 0x27
define I2C_SLV1_ADDR 0x28
define I2C_SLV1_REG 0x29
define I2C_SLV1_CTRL 0x2A
define I2C_SLV2_ADDR 0x2B
define I2C_SLV2_REG 0x2C
define I2C_SLV2_CTRL 0x2D
define I2C_SLV3_ADDR 0x2E
define I2C_SLV3_REG 0x2F
define I2C_SLV3_CTRL 0x30
define I2C_SLV4_ADDR 0x31
define I2C_SLV4_REG 0x32
define I2C_SLV4_DO 0x33
define I2C_SLV4_CTRL 0x34
define I2C_SLV4_DI 0x35
define I2C_MST_STATUS 0x36
define INT_PIN_CFG 0x37
define INT_ENABLE 0x38
define DMP_INT_STATUS 0x39 // Check DMP interrupt
define INT_STATUS 0x3A
define ACCEL_XOUT_H 0x3B
define ACCEL_XOUT_L 0x3C
define ACCEL_YOUT_H 0x3D
define ACCEL_YOUT_L 0x3E
define ACCEL_ZOUT_H 0x3F
define ACCEL_ZOUT_L 0x40
define TEMP_OUT_H 0x41
define TEMP_OUT_L 0x42
define GYRO_XOUT_H 0x43
define GYRO_XOUT_L 0x44
define GYRO_YOUT_H 0x45
define GYRO_YOUT_L 0x46
define GYRO_ZOUT_H 0x47
define GYRO_ZOUT_L 0x48
define EXT_SENS_DATA_00 0x49
define EXT_SENS_DATA_01 0x4A
define EXT_SENS_DATA_02 0x4B
define EXT_SENS_DATA_03 0x4C
define EXT_SENS_DATA_04 0x4D
define EXT_SENS_DATA_05 0x4E
define EXT_SENS_DATA_06 0x4F
define EXT_SENS_DATA_07 0x50
define EXT_SENS_DATA_08 0x51
define EXT_SENS_DATA_09 0x52
define EXT_SENS_DATA_10 0x53
define EXT_SENS_DATA_11 0x54
define EXT_SENS_DATA_12 0x55
define EXT_SENS_DATA_13 0x56
define EXT_SENS_DATA_14 0x57
define EXT_SENS_DATA_15 0x58
define EXT_SENS_DATA_16 0x59
define EXT_SENS_DATA_17 0x5A
define EXT_SENS_DATA_18 0x5B
define EXT_SENS_DATA_19 0x5C
define EXT_SENS_DATA_20 0x5D
define EXT_SENS_DATA_21 0x5E
define EXT_SENS_DATA_22 0x5F
define EXT_SENS_DATA_23 0x60
define MOT_DETECT_STATUS 0x61
define I2C_SLV0_DO 0x63
define I2C_SLV1_DO 0x64
define I2C_SLV2_DO 0x65
define I2C_SLV3_DO 0x66
define I2C_MST_DELAY_CTRL 0x67
define SIGNAL_PATH_RESET 0x68
define MOT_DETECT_CTRL 0x69
define USER_CTRL 0x6A // Bit 7 enable DMP, bit 3 reset DMP
define PWR_MGMT_1 0x6B // Device defaults to the SLEEP mode
define PWR_MGMT_2 0x6C
define DMP_BANK 0x6D // Activates a specific bank in the DMP
define DMP_RW_PNT 0x6E // Set read/write pointer to a specific start address in specified DMP bank
define DMP_REG 0x6F // Register in DMP from which to read or to which to write
define DMP_REG_1 0x70
define DMP_REG_2 0x71
define FIFO_COUNTH 0x72
define FIFO_COUNTL 0x73
define FIFO_R_W 0x74
define WHO_AM_I_MPU9250 0x75 // Should return 0x73
define XA_OFFSET_H 0x77
define XA_OFFSET_L 0x78
define YA_OFFSET_H 0x7A
define YA_OFFSET_L 0x7B
define ZA_OFFSET_H 0x7D
define ZA_OFFSET_L 0x7E
// Using the MPU9250_MS5637 Add-On shield, ADO is set to 0 // Seven-bit device address is 110100 for ADO = 0 and 110101 for ADO = 1
define ADO 0
if ADO
define MPU9250_ADDRESS 0x69 // Device address when ADO = 1
define AK8963_ADDRESS 0x0C // Address of magnetometer
else
define MPU9250_ADDRESS 0x68 // Device address when ADO = 0
define AK8963_ADDRESS 0x0C // Address of magnetometer
endif
define SerialDebug true // set to true to get Serial output for debugging
// Set initial input parameters enum Ascale { AFS_2G = 0, AFS_4G, AFS_8G, AFS_16G };
enum Gscale { GFS_250DPS = 0, GFS_500DPS, GFS_1000DPS, GFS_2000DPS };
enum Mscale { MFS_14BITS = 0, // 0.6 mG per LSB MFS_16BITS // 0.15 mG per LSB };
define ADC_256 0x00 // define pressure and temperature conversion rates
define ADC_512 0x02
define ADC_1024 0x04
define ADC_2048 0x06
define ADC_4096 0x08
define ADC_8192 0x0A
define ADC_D1 0x40
define ADC_D2 0x50
// Specify sensor full scale uint8_t OSR = ADC_8192; // set pressure amd temperature oversample rate uint8_t Gscale = GFS_250DPS; uint8_t Ascale = AFS_2G; uint8_t Mscale = MFS_16BITS; // Choose either 14-bit or 16-bit magnetometer resolution uint8_t Mmode = 0x06; // 2 for 8 Hz, 6 for 100 Hz continuous magnetometer data read float aRes, gRes, mRes; // scale resolutions per LSB for the sensors
// Pin definitions int intPin = 14; // can be any pin bool newData = false; bool newMagData = false;
int myLed = 5;
int16_t MPU9250Data[7]; // used to read all 14 bytes at once from the MPU9250 accel/gyro int16_t accelCount[3]; // Stores the 16-bit signed accelerometer sensor output int16_t gyroCount[3]; // Stores the 16-bit signed gyro sensor output int16_t magCount[3]; // Stores the 16-bit signed magnetometer sensor output float magCalibration[3] = {0, 0, 0}; // Factory mag calibration and mag bias float gyroBias[3] = {0, 0, 0}, accelBias[3] = {0, 0, 0}, magBias[3] = {0, 0, 0}, magScale[3] = {0, 0, 0}; // Bias corrections for gyro and accelerometer int16_t tempCount; // temperature raw count output float temperature; // Stores the MPU9250 gyro internal chip temperature in degrees Celsius
float SelfTest[6]; // holds results of gyro and accelerometer self test
// global constants for 9 DoF fusion and AHRS (Attitude and Heading Reference System) float pi = 3.141592653589793238462643383279502884f; float GyroMeasError = PI (4.0f / 180.0f); // gyroscope measurement error in rads/s (start at 40 deg/s) float GyroMeasDrift = PI (0.0f / 180.0f); // gyroscope measurement drift in rad/s/s (start at 0.0 deg/s/s) // There is a tradeoff in the beta parameter between accuracy and response speed. // In the original Madgwick study, beta of 0.041 (corresponding to GyroMeasError of 2.7 degrees/s) was found to give optimal accuracy. // However, with this value, the LSM9SD0 response time is about 10 seconds to a stable initial quaternion. // Subsequent changes also require a longish lag time to a stable output, not fast enough for a quadcopter or robot car! // By increasing beta (GyroMeasError) by about a factor of fifteen, the response time constant is reduced to ~2 sec // I haven't noticed any reduction in solution accuracy. This is essentially the I coefficient in a PID control sense; // the bigger the feedback coefficient, the faster the solution converges, usually at the expense of accuracy. // In any case, this is the free parameter in the Madgwick filtering and fusion scheme. float beta = sqrt(3.0f / 4.0f) GyroMeasError; // compute beta float zeta = sqrt(3.0f / 4.0f) GyroMeasDrift; // compute zeta, the other free parameter in the Madgwick scheme usually set to a small or zero value
define Kp 2.0f * 5.0f // these are the free parameters in the Mahony filter and fusion scheme, Kp for proportional feedback, Ki for integral
define Ki 0.0f
uint32_t delt_t = 0, count = 0, sumCount = 0; // used to control display output rate float pitch, yaw, roll; float a12, a22, a31, a32, a33; // rotation matrix coefficients for Euler angles and gravity components float deltat = 0.0f, sum = 0.0f; // integration interval for both filter schemes uint32_t lastUpdate = 0, firstUpdate = 0; // used to calculate integration interval uint32_t Now = 0; // used to calculate integration interval
float ax, ay, az, gx, gy, gz, mx, my, mz; // variables to hold latest sensor data values float lin_ax, lin_ay, lin_az; // linear acceleration (acceleration with gravity component subtracted) float q[4] = {1.0f, 0.0f, 0.0f, 0.0f}; // vector to hold quaternion float eInt[3] = {0.0f, 0.0f, 0.0f}; // vector to hold integral error for Mahony method
void setup() { Serial.begin(115200); delay(4000);
Wire.begin(); Wire.setClock(400000); // two i2c speeds supported: 100kbs or 400kbs delay(1000);
// Set up the interrupt pin, its set as active high, push-pull pinMode(intPin, INPUT); pinMode(myLed, OUTPUT); digitalWrite(myLed, LOW);
I2Cscan();// look for I2C devices on the bus
// Read the WHO_AM_I register, this is a good test of communication Serial.println("MPU9250 9-axis motion sensor..."); uint8_t c = readByte(MPU9250_ADDRESS, WHO_AM_I_MPU9250); // Read WHO_AM_I register for MPU-9250 Serial.print("MPU9250 "); Serial.print("I AM "); Serial.print(c, HEX); Serial.print(" I should be "); Serial.println(0x73, HEX);
delay(1000);
if (c == 0x73) // WHO_AM_I should always be 0x73 { Serial.println("MPU9250 is online...");
MPU9250SelfTest(SelfTest); // Start by performing self test and reporting values Serial.print("x-axis self test: acceleration trim within : "); Serial.print(SelfTest[0],1); Serial.println("% of factory value"); Serial.print("y-axis self test: acceleration trim within : "); Serial.print(SelfTest[1],1); Serial.println("% of factory value"); Serial.print("z-axis self test: acceleration trim within : "); Serial.print(SelfTest[2],1); Serial.println("% of factory value"); Serial.print("x-axis self test: gyration trim within : "); Serial.print(SelfTest[3],1); Serial.println("% of factory value"); Serial.print("y-axis self test: gyration trim within : "); Serial.print(SelfTest[4],1); Serial.println("% of factory value"); Serial.print("z-axis self test: gyration trim within : "); Serial.print(SelfTest[5],1); Serial.println("% of factory value"); delay(1000);
// get sensor resolutions, only need to do this once getAres(); getGres(); getMres();
Serial.println(" Calibrate gyro and accel"); accelgyrocalMPU9250(gyroBias, accelBias); // Calibrate gyro and accelerometers, load biases in bias registers Serial.println("accel biases (mg)"); Serial.println(1000.accelBias[0]); Serial.println(1000.accelBias[1]); Serial.println(1000.*accelBias[2]); Serial.println("gyro biases (dps)"); Serial.println(gyroBias[0]); Serial.println(gyroBias[1]); Serial.println(gyroBias[2]);
delay(1000);
initMPU9250(); Serial.println("MPU9250 initialized for active data mode...."); // Initialize device for active mode read of acclerometer, gyroscope, and temperature
// Read the WHO_AM_I register of the magnetometer, this is a good test of communication byte d = readByte(AK8963_ADDRESS, WHO_AM_I_AK8963); // Read WHO_AM_I register for AK8963 Serial.print("AK8963 "); Serial.print("I AM "); Serial.print(d, HEX); Serial.print(" I should be "); Serial.println(0x48, HEX);
delay(1000);
// Get magnetometer calibration from AK8963 ROM initAK8963(magCalibration); Serial.println("AK8963 initialized for active data mode...."); // Initialize device for active mode read of magnetometer
magcalMPU9250(magBias, magScale); Serial.println("AK8963 mag biases (mG)"); Serial.println(magBias[0]); Serial.println(magBias[1]); Serial.println(magBias[2]); Serial.println("AK8963 mag scale (mG)"); Serial.println(magScale[0]); Serial.println(magScale[1]); Serial.println(magScale[2]); delay(2000); // add delay to see results before serial spew of data
if(SerialDebug) { // Serial.println("Calibration values: "); Serial.print("X-Axis sensitivity adjustment value "); Serial.println(magCalibration[0], 2); Serial.print("Y-Axis sensitivity adjustment value "); Serial.println(magCalibration[1], 2); Serial.print("Z-Axis sensitivity adjustment value "); Serial.println(magCalibration[2], 2); }
delay(1000);
// attachInterrupt(digitalPinToInterrupt(intPin), myinthandler, RISING); // define interrupt for INT pin output of MPU9250 attachInterrupt(intPin, myinthandler, RISING); // define interrupt for INT pin output of MPU9250 } else { Serial.print("Could not connect to MPU9250: 0x"); Serial.println(c, HEX); while(1) ; // Loop forever if communication doesn't happen }
}
void loop() { // If intPin goes high, all data registers have new data if(newData == true) { // On interrupt, read data newData = false; // reset newData flag readMPU9250Data(MPU9250Data); // INT cleared on any read
// Now we'll calculate the accleration value into actual g's ax = (float)MPU9250Data[0]*aRes - accelBias[0]; // get actual g value, this depends on scale being set ay = (float)MPU9250Data[1]*aRes - accelBias[1]; az = (float)MPU9250Data[2]*aRes - accelBias[2]; // Calculate the gyro value into actual degrees per second gx = (float)MPU9250Data[4]*gRes; // get actual gyro value, this depends on scale being set gy = (float)MPU9250Data[5]*gRes; gz = (float)MPU9250Data[6]*gRes; newMagData = (readByte(AK8963_ADDRESS, AK8963_ST1) & 0x01); if(newMagData == true) { // wait for magnetometer data ready bit to be set readMagData(magCount); // Read the x/y/z adc values // Calculate the magnetometer values in milliGauss // Include factory calibration per data sheet and user environmental corrections mx = (float)magCount[0]*mRes*magCalibration[0] - magBias[0]; // get actual magnetometer value, this depends on scale being set my = (float)magCount[1]*mRes*magCalibration[1] - magBias[1]; mz = (float)magCount[2]*mRes*magCalibration[2] - magBias[2]; mx *= magScale[0]; my *= magScale[1]; mz *= magScale[2]; } for(uint8_t i = 0; i < 10; i++) { // iterate a fixed number of times per data read cycle Now = micros(); deltat = ((Now - lastUpdate)/1000000.0f); // set integration time by time elapsed since last filter update lastUpdate = Now; sum += deltat; // sum for averaging filter update rate sumCount++; MadgwickQuaternionUpdate(-ax, ay, az, gx*pi/180.0f, -gy*pi/180.0f, -gz*pi/180.0f, my, -mx, mz); }
}
// Serial print and/or display at 0.5 s rate independent of data rates delt_t = millis() - count; if (delt_t > 500) { // update LCD once per half-second independent of read rate
if(SerialDebug) {
// Serial.print("ax = "); Serial.print((int)1000ax); // Serial.print(" ay = "); Serial.print((int)1000ay); // Serial.print(" az = "); Serial.print((int)1000*az); Serial.println(" mg"); // Serial.print("gx = "); Serial.print( gx, 2); // Serial.print(" gy = "); Serial.print( gy, 2); // Serial.print(" gz = "); Serial.print( gz, 2); Serial.println(" deg/s"); // Serial.print("mx = "); Serial.print( (int)mx ); // Serial.print(" my = "); Serial.print( (int)my ); // Serial.print(" mz = "); Serial.print( (int)mz ); Serial.println(" mG");
Serial.print("q0 = "); Serial.print(q[0]); Serial.print(" qx = "); Serial.print(q[1]); Serial.print(" qy = "); Serial.print(q[2]); Serial.print(" qz = "); Serial.println(q[3]); } tempCount = readTempData(); // Read the gyro adc values temperature = ((float) tempCount) / 333.87f + 21.0f; // Gyro chip temperature in degrees Centigrade
// Print temperature in degrees Centigrade Serial.print("Gyro temperature is "); Serial.print(temperature, 1); Serial.println(" degrees C"); // Print T values to tenths of s degree C
// Define output variables from updated quaternion---these are Tait-Bryan angles, commonly used in aircraft orientation. // In this coordinate system, the positive z-axis is down toward Earth. // Yaw is the angle between Sensor x-axis and Earth magnetic North (or true North if corrected for local declination, looking down on the sensor positive yaw is counterclockwise. // Pitch is angle between sensor x-axis and Earth ground plane, toward the Earth is positive, up toward the sky is negative. // Roll is angle between sensor y-axis and Earth ground plane, y-axis up is positive roll. // These arise from the definition of the homogeneous rotation matrix constructed from quaternions. // Tait-Bryan angles as well as Euler angles are non-commutative; that is, the get the correct orientation the rotations must be // applied in the correct order which for this configuration is yaw, pitch, and then roll. // For more see http://en.wikipedia.org/wiki/Conversion_between_quaternions_and_Euler_angles which has additional links. //Software AHRS: // yaw = atan2f(2.0f (q[1] q[2] + q[0] q[3]), q[0] q[0] + q[1] q[1] - q[2] q[2] - q[3] q[3]); // pitch = -asinf(2.0f (q[1] q[3] - q[0] q[2])); // roll = atan2f(2.0f (q[0] q[1] + q[2] q[3]), q[0] q[0] - q[1] q[1] - q[2] q[2] + q[3] q[3]); // pitch = 180.0f / PI; // yaw = 180.0f / PI; // yaw += 13.8f; // Declination at Danville, California is 13 degrees 48 minutes and 47 seconds on 2014-04-04 // if(yaw < 0) yaw += 360.0f; // Ensure yaw stays between 0 and 360 // roll = 180.0f / PI; a12 = 2.0f (q[1] q[2] + q[0] q[3]); a22 = q[0] q[0] + q[1] q[1] - q[2] q[2] - q[3] q[3]; a31 = 2.0f (q[0] q[1] + q[2] q[3]); a32 = 2.0f (q[1] q[3] - q[0] q[2]); a33 = q[0] q[0] - q[1] q[1] - q[2] q[2] + q[3] q[3]; pitch = -asin(a32); roll = atan2(a31, a33); yaw = atan2(a12, a22); pitch = 180.0f / pi; yaw = 180.0f / pi; yaw += 13.8f; // Declination at Danville, California is 13 degrees 48 minutes and 47 seconds on 2014-04-04 if(yaw < 0) yaw += 360.0f; // Ensure yaw stays between 0 and 360 roll = 180.0f / pi; lin_ax = ax + a31; lin_ay = ay + a32; lin_az = az - a33; if(SerialDebug) { Serial.print("Yaw, Pitch, Roll: "); Serial.print(yaw, 2); Serial.print(", "); Serial.print(pitch, 2); Serial.print(", "); Serial.println(roll, 2);
Serial.print("Grav_x, Grav_y, Grav_z: "); Serial.print(-a31*1000.0f, 2); Serial.print(", "); Serial.print(-a32*1000.0f, 2); Serial.print(", "); Serial.print(a33*1000.0f, 2); Serial.println(" mg"); Serial.print("Lin_ax, Lin_ay, Lin_az: "); Serial.print(lin_ax*1000.0f, 2); Serial.print(", "); Serial.print(lin_ay*1000.0f, 2); Serial.print(", "); Serial.print(lin_az*1000.0f, 2); Serial.println(" mg"); Serial.print("sumCount = "); Serial.println(sumCount); Serial.print("sum = "); Serial.println(sum); Serial.print("rate = "); Serial.print((float)sumCount/sum, 2); Serial.println(" Hz"); } digitalWrite(myLed, !digitalRead(myLed)); count = millis(); sumCount = 0; sum = 0; }
}
//=================================================================================================================== //====== Set of useful function to access acceleration. gyroscope, magnetometer, and temperature data //===================================================================================================================
void myinthandler() { newData = true; }
void getMres() { switch (Mscale) { // Possible magnetometer scales (and their register bit settings) are: // 14 bit resolution (0) and 16 bit resolution (1) case MFS_14BITS: mRes = 10.4912./8190.; // Proper scale to return milliGauss break; case MFS_16BITS: mRes = 10.4912./32760.0; // Proper scale to return milliGauss break; } }
void getGres() { switch (Gscale) { // Possible gyro scales (and their register bit settings) are: // 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS (11). // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value: case GFS_250DPS: gRes = 250.0/32768.0; break; case GFS_500DPS: gRes = 500.0/32768.0; break; case GFS_1000DPS: gRes = 1000.0/32768.0; break; case GFS_2000DPS: gRes = 2000.0/32768.0; break; } }
void getAres() { switch (Ascale) { // Possible accelerometer scales (and their register bit settings) are: // 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs (11). // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value: case AFS_2G: aRes = 2.0/32768.0; break; case AFS_4G: aRes = 4.0/32768.0; break; case AFS_8G: aRes = 8.0/32768.0; break; case AFS_16G: aRes = 16.0/32768.0; break; } }
void readMPU9250Data(int16_t * destination) { uint8_t rawData[14]; // x/y/z accel register data stored here readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 14, &rawData[0]); // Read the 14 raw data registers into data array destination[0] = ((int16_t)rawData[0] << 8) | rawData[1] ; // Turn the MSB and LSB into a signed 16-bit value destination[1] = ((int16_t)rawData[2] << 8) | rawData[3] ; destination[2] = ((int16_t)rawData[4] << 8) | rawData[5] ; destination[3] = ((int16_t)rawData[6] << 8) | rawData[7] ; destination[4] = ((int16_t)rawData[8] << 8) | rawData[9] ; destination[5] = ((int16_t)rawData[10] << 8) | rawData[11] ; destination[6] = ((int16_t)rawData[12] << 8) | rawData[13] ; }
void readAccelData(int16_t * destination) { uint8_t rawData[6]; // x/y/z accel register data stored here readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array destination[0] = ((int16_t)rawData[0] << 8) | rawData[1] ; // Turn the MSB and LSB into a signed 16-bit value destination[1] = ((int16_t)rawData[2] << 8) | rawData[3] ; destination[2] = ((int16_t)rawData[4] << 8) | rawData[5] ; }
void readGyroData(int16_t * destination) { uint8_t rawData[6]; // x/y/z gyro register data stored here readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array destination[0] = ((int16_t)rawData[0] << 8) | rawData[1] ; // Turn the MSB and LSB into a signed 16-bit value destination[1] = ((int16_t)rawData[2] << 8) | rawData[3] ; destination[2] = ((int16_t)rawData[4] << 8) | rawData[5] ; }
void readMagData(int16_t * destination) { uint8_t rawData[7]; // x/y/z gyro register data, ST2 register stored here, must read ST2 at end of data acquisition readBytes(AK8963_ADDRESS, AK8963_XOUT_L, 7, &rawData[0]); // Read the six raw data and ST2 registers sequentially into data array uint8_t c = rawData[6]; // End data read by reading ST2 register if(!(c & 0x08)) { // Check if magnetic sensor overflow set, if not then report data destination[0] = ((int16_t)rawData[1] << 8) | rawData[0] ; // Turn the MSB and LSB into a signed 16-bit value destination[1] = ((int16_t)rawData[3] << 8) | rawData[2] ; // Data stored as little Endian destination[2] = ((int16_t)rawData[5] << 8) | rawData[4] ; } }
int16_t readTempData() { uint8_t rawData[2]; // x/y/z gyro register data stored here readBytes(MPU9250_ADDRESS, TEMP_OUT_H, 2, &rawData[0]); // Read the two raw data registers sequentially into data array return ((int16_t)rawData[0] << 8) | rawData[1] ; // Turn the MSB and LSB into a 16-bit value }
void initAK8963(float * destination) { // First extract the factory calibration for each magnetometer axis uint8_t rawData[3]; // x/y/z gyro calibration data stored here writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x00); // Power down magnetometer delay(10); writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x0F); // Enter Fuse ROM access mode delay(10); readBytes(AK8963_ADDRESS, AK8963_ASAX, 3, &rawData[0]); // Read the x-, y-, and z-axis calibration values destination[0] = (float)(rawData[0] - 128)/256. + 1.; // Return x-axis sensitivity adjustment values, etc. destination[1] = (float)(rawData[1] - 128)/256. + 1.; destination[2] = (float)(rawData[2] - 128)/256. + 1.; writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x00); // Power down magnetometer delay(10); // Configure the magnetometer for continuous read and highest resolution // set Mscale bit 4 to 1 (0) to enable 16 (14) bit resolution in CNTL register, // and enable continuous mode data acquisition Mmode (bits [3:0]), 0010 for 8 Hz and 0110 for 100 Hz sample rates writeByte(AK8963_ADDRESS, AK8963_CNTL, Mscale << 4 | Mmode); // Set magnetometer data resolution and sample ODR delay(10); }
void initMPU9250() { // wake up device writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors delay(100); // Wait for all registers to reset
// get stable time source writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x01); // Auto select clock source to be PLL gyroscope reference if ready else delay(200);
// Configure Gyro and Thermometer // Disable FSYNC and set thermometer and gyro bandwidth to 41 and 42 Hz, respectively; // minimum delay time for this setting is 5.9 ms, which means sensor fusion update rates cannot // be higher than 1 / 0.0059 = 170 Hz // DLPF_CFG = bits 2:0 = 011; this limits the sample rate to 1000 Hz for both // With the MPU9250, it is possible to get gyro sample rates of 32 kHz (!), 8 kHz, or 1 kHz writeByte(MPU9250_ADDRESS, CONFIG, 0x03);
// Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV) writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x04); // Use a 200 Hz rate; a rate consistent with the filter update rate // determined inset in CONFIG above
// Set gyroscope full scale range // Range selects FS_SEL and GFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3 uint8_t c = readByte(MPU9250_ADDRESS, GYRO_CONFIG); // get current GYRO_CONFIG register value // c = c & ~0xE0; // Clear self-test bits [7:5] c = c & ~0x03; // Clear Fchoice bits [1:0] c = c & ~0x18; // Clear GFS bits [4:3] c = c | Gscale << 3; // Set full scale range for the gyro // c =| 0x00; // Set Fchoice for the gyro to 11 by writing its inverse to bits 1:0 of GYRO_CONFIG writeByte(MPU9250_ADDRESS, GYRO_CONFIG, c ); // Write new GYRO_CONFIG value to register
// Set accelerometer full-scale range configuration c = readByte(MPU9250_ADDRESS, ACCEL_CONFIG); // get current ACCEL_CONFIG register value // c = c & ~0xE0; // Clear self-test bits [7:5] c = c & ~0x18; // Clear AFS bits [4:3] c = c | Ascale << 3; // Set full scale range for the accelerometer writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, c); // Write new ACCEL_CONFIG register value
// Set accelerometer sample rate configuration // It is possible to get a 4 kHz sample rate from the accelerometer by choosing 1 for // accel_fchoice_b bit [3]; in this case the bandwidth is 1.13 kHz c = readByte(MPU9250_ADDRESS, ACCEL_CONFIG2); // get current ACCEL_CONFIG2 register value c = c & ~0x0F; // Clear accel_fchoice_b (bit 3) and A_DLPFG (bits [2:0]) c = c | 0x03; // Set accelerometer rate to 1 kHz and bandwidth to 41 Hz writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, c); // Write new ACCEL_CONFIG2 register value
// The accelerometer, gyro, and thermometer are set to 1 kHz sample rates, // but all these rates are further reduced by a factor of 5 to 200 Hz because of the SMPLRT_DIV setting
// Configure Interrupts and Bypass Enable // Set interrupt pin active high, push-pull, hold interrupt pin level HIGH until interrupt cleared, // clear on read of INT_STATUS, and enable I2C_BYPASS_EN so additional chips // can join the I2C bus and all can be controlled by the Arduino as master // writeByte(MPU9250_ADDRESS, INT_PIN_CFG, 0x22); writeByte(MPU9250_ADDRESS, INT_PIN_CFG, 0x12); // INT is 50 microsecond pulse and any read to clear writeByte(MPU9250_ADDRESS, INT_ENABLE, 0x01); // Enable data ready (bit 0) interrupt delay(100); }
// Function which accumulates gyro and accelerometer data after device initialization. It calculates the average // of the at-rest readings and then loads the resulting offsets into accelerometer and gyro bias registers. void accelgyrocalMPU9250(float dest1, float dest2) { uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data uint16_t ii, packet_count, fifo_count; int32_t gyro_bias[3] = {0, 0, 0}, accel_bias[3] = {0, 0, 0};
// reset device writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device delay(100);
// get stable time source; Auto select clock source to be PLL gyroscope reference if ready // else use the internal oscillator, bits 2:0 = 001 writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x01); writeByte(MPU9250_ADDRESS, PWR_MGMT_2, 0x00); delay(200);
// Configure device for bias calculation writeByte(MPU9250_ADDRESS, INT_ENABLE, 0x00); // Disable all interrupts writeByte(MPU9250_ADDRESS, FIFO_EN, 0x00); // Disable FIFO writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x00); // Turn on internal clock source writeByte(MPU9250_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master writeByte(MPU9250_ADDRESS, USER_CTRL, 0x00); // Disable FIFO and I2C master modes writeByte(MPU9250_ADDRESS, USER_CTRL, 0x0C); // Reset FIFO and DMP delay(15);
// Configure MPU6050 gyro and accelerometer for bias calculation writeByte(MPU9250_ADDRESS, CONFIG, 0x01); // Set low-pass filter to 188 Hz writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set sample rate to 1 kHz writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0x00); // Set gyro full-scale to 250 degrees per second, maximum sensitivity writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity
uint16_t gyrosensitivity = 131; // = 131 LSB/degrees/sec uint16_t accelsensitivity = 16384; // = 16384 LSB/g
// Configure FIFO to capture accelerometer and gyro data for bias calculation writeByte(MPU9250_ADDRESS, USER_CTRL, 0x40); // Enable FIFO writeByte(MPU9250_ADDRESS, FIFO_EN, 0x78); // Enable gyro and accelerometer sensors for FIFO (max size 512 bytes in MPU-9150) delay(40); // accumulate 40 samples in 40 milliseconds = 480 bytes
// At end of sample accumulation, turn off FIFO sensor read writeByte(MPU9250_ADDRESS, FIFO_EN, 0x00); // Disable gyro and accelerometer sensors for FIFO readBytes(MPU9250_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count fifo_count = ((uint16_t)data[0] << 8) | data[1]; packet_count = fifo_count/12;// How many sets of full gyro and accelerometer data for averaging
for (ii = 0; ii < packet_count; ii++) { int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0}; readBytes(MPU9250_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1] ) ; // Form signed 16-bit integer for each sample in FIFO accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3] ) ; accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5] ) ; gyro_temp[0] = (int16_t) (((int16_t)data[6] << 8) | data[7] ) ; gyro_temp[1] = (int16_t) (((int16_t)data[8] << 8) | data[9] ) ; gyro_temp[2] = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;
accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases accel_bias[1] += (int32_t) accel_temp[1]; accel_bias[2] += (int32_t) accel_temp[2]; gyro_bias[0] += (int32_t) gyro_temp[0]; gyro_bias[1] += (int32_t) gyro_temp[1]; gyro_bias[2] += (int32_t) gyro_temp[2];
} accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases accel_bias[1] /= (int32_t) packet_count; accel_bias[2] /= (int32_t) packet_count; gyro_bias[0] /= (int32_t) packet_count; gyro_bias[1] /= (int32_t) packet_count; gyro_bias[2] /= (int32_t) packet_count;
if(accel_bias[2] > 0L) {accel_bias[2] -= (int32_t) accelsensitivity;} // Remove gravity from the z-axis accelerometer bias calculation else {accel_bias[2] += (int32_t) accelsensitivity;}
// Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup data[0] = (-gyro_bias[0]/4 >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format data[1] = (-gyro_bias[0]/4) & 0xFF; // Biases are additive, so change sign on calculated average gyro biases data[2] = (-gyro_bias[1]/4 >> 8) & 0xFF; data[3] = (-gyro_bias[1]/4) & 0xFF; data[4] = (-gyro_bias[2]/4 >> 8) & 0xFF; data[5] = (-gyro_bias[2]/4) & 0xFF;
// Push gyro biases to hardware registers writeByte(MPU9250_ADDRESS, XG_OFFSET_H, data[0]); writeByte(MPU9250_ADDRESS, XG_OFFSET_L, data[1]); writeByte(MPU9250_ADDRESS, YG_OFFSET_H, data[2]); writeByte(MPU9250_ADDRESS, YG_OFFSET_L, data[3]); writeByte(MPU9250_ADDRESS, ZG_OFFSET_H, data[4]); writeByte(MPU9250_ADDRESS, ZG_OFFSET_L, data[5]);
// Output scaled gyro biases for display in the main program dest1[0] = (float) gyro_bias[0]/(float) gyrosensitivity; dest1[1] = (float) gyro_bias[1]/(float) gyrosensitivity; dest1[2] = (float) gyro_bias[2]/(float) gyrosensitivity;
// Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain // factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold // non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature // compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that // the accelerometer biases calculated above must be divided by 8.
int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases readBytes(MPU9250_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values accel_bias_reg[0] = (int32_t) (((int16_t)data[0] << 8) | data[1]); readBytes(MPU9250_ADDRESS, YA_OFFSET_H, 2, &data[0]); accel_bias_reg[1] = (int32_t) (((int16_t)data[0] << 8) | data[1]); readBytes(MPU9250_ADDRESS, ZA_OFFSET_H, 2, &data[0]); accel_bias_reg[2] = (int32_t) (((int16_t)data[0] << 8) | data[1]);
uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis
for(ii = 0; ii < 3; ii++) { if((accel_bias_reg[ii] & mask)) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit }
// Construct total accelerometer bias, including calculated average accelerometer bias from above accel_bias_reg[0] -= (accel_bias[0]/8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale) accel_bias_reg[1] -= (accel_bias[1]/8); accel_bias_reg[2] -= (accel_bias[2]/8);
data[0] = (accel_bias_reg[0] >> 8) & 0xFF; data[1] = (accel_bias_reg[0]) & 0xFF; data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers data[2] = (accel_bias_reg[1] >> 8) & 0xFF; data[3] = (accel_bias_reg[1]) & 0xFF; data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers data[4] = (accel_bias_reg[2] >> 8) & 0xFF; data[5] = (accel_bias_reg[2]) & 0xFF; data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers
// Apparently this is not working for the acceleration biases in the MPU-9250 // Are we handling the temperature correction bit properly? // Push accelerometer biases to hardware registers / writeByte(MPU9250_ADDRESS, XA_OFFSET_H, data[0]); writeByte(MPU9250_ADDRESS, XA_OFFSET_L, data[1]); writeByte(MPU9250_ADDRESS, YA_OFFSET_H, data[2]); writeByte(MPU9250_ADDRESS, YA_OFFSET_L, data[3]); writeByte(MPU9250_ADDRESS, ZA_OFFSET_H, data[4]); writeByte(MPU9250_ADDRESS, ZA_OFFSET_L, data[5]); / // Output scaled accelerometer biases for display in the main program dest2[0] = (float)accel_bias[0]/(float)accelsensitivity; dest2[1] = (float)accel_bias[1]/(float)accelsensitivity; dest2[2] = (float)accel_bias[2]/(float)accelsensitivity; }
void magcalMPU9250(float dest1, float dest2) { uint16_t ii = 0, sample_count = 0; int32_t mag_bias[3] = {0, 0, 0}, mag_scale[3] = {0, 0, 0}; int16_t mag_max[3] = {-32767, -32767, -32767}, mag_min[3] = {32767, 32767, 32767}, mag_temp[3] = {0, 0, 0};
Serial.println("Mag Calibration: Wave device in a figure eight until done!"); delay(4000);
// shoot for ~fifteen seconds of mag data if(Mmode == 0x02) sample_count = 128; // at 8 Hz ODR, new mag data is available every 125 ms if(Mmode == 0x06) sample_count = 1500; // at 100 Hz ODR, new mag data is available every 10 ms
for(ii = 0; ii < sample_count; ii++) { readMagData(mag_temp); // Read the mag data for (int jj = 0; jj < 3; jj++) { if(mag_temp[jj] > mag_max[jj]) mag_max[jj] = mag_temp[jj]; if(mag_temp[jj] < mag_min[jj]) mag_min[jj] = mag_temp[jj]; } if(Mmode == 0x02) delay(135); // at 8 Hz ODR, new mag data is available every 125 ms if(Mmode == 0x06) delay(12); // at 100 Hz ODR, new mag data is available every 10 ms }
// Serial.println("mag x min/max:"); Serial.println(mag_max[0]); Serial.println(mag_min[0]); // Serial.println("mag y min/max:"); Serial.println(mag_max[1]); Serial.println(mag_min[1]); // Serial.println("mag z min/max:"); Serial.println(mag_max[2]); Serial.println(mag_min[2]);
// Get hard iron correction mag_bias[0] = (mag_max[0] + mag_min[0])/2; // get average x mag bias in counts mag_bias[1] = (mag_max[1] + mag_min[1])/2; // get average y mag bias in counts mag_bias[2] = (mag_max[2] + mag_min[2])/2; // get average z mag bias in counts dest1[0] = (float) mag_bias[0]*mRes*magCalibration[0]; // save mag biases in G for main program dest1[1] = (float) mag_bias[1]*mRes*magCalibration[1]; dest1[2] = (float) mag_bias[2]*mRes*magCalibration[2]; // Get soft iron correction estimate mag_scale[0] = (mag_max[0] - mag_min[0])/2; // get average x axis max chord length in counts mag_scale[1] = (mag_max[1] - mag_min[1])/2; // get average y axis max chord length in counts mag_scale[2] = (mag_max[2] - mag_min[2])/2; // get average z axis max chord length in counts float avg_rad = mag_scale[0] + mag_scale[1] + mag_scale[2]; avg_rad /= 3.0; dest2[0] = avg_rad/((float)mag_scale[0]); dest2[1] = avg_rad/((float)mag_scale[1]); dest2[2] = avg_rad/((float)mag_scale[2]);
Serial.println("Mag Calibration done!"); }
// Accelerometer and gyroscope self test; check calibration wrt factory settings void MPU9250SelfTest(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass { uint8_t rawData[6] = {0, 0, 0, 0, 0, 0}; uint8_t selfTest[6]; int32_t gAvg[3] = {0}, aAvg[3] = {0}, aSTAvg[3] = {0}, gSTAvg[3] = {0}; float factoryTrim[6]; uint8_t FS = 0;
writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set gyro sample rate to 1 kHz writeByte(MPU9250_ADDRESS, CONFIG, 0x02); // Set gyro sample rate to 1 kHz and DLPF to 92 Hz writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 1<<FS); // Set full scale range for the gyro to 250 dps writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, 0x02); // Set accelerometer rate to 1 kHz and bandwidth to 92 Hz writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 1<<FS); // Set full scale range for the accelerometer to 2 g
for( int ii = 0; ii < 200; ii++) { // get average current values of gyro and acclerometer
readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array aAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value aAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ; aAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
gAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value gAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ; gAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ; }
for (int ii =0; ii < 3; ii++) { // Get average of 200 values and store as average current readings aAvg[ii] /= 200; gAvg[ii] /= 200; }
// Configure the accelerometer for self-test writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0xE0); // Enable self test on all three axes and set accelerometer range to +/- 2 g writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s delay(25); // Delay a while to let the device stabilize
for( int ii = 0; ii < 200; ii++) { // get average self-test values of gyro and acclerometer
readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array aSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value aSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ; aSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
gSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value gSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ; gSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ; }
for (int ii =0; ii < 3; ii++) { // Get average of 200 values and store as average self-test readings aSTAvg[ii] /= 200; gSTAvg[ii] /= 200; }
// Configure the gyro and accelerometer for normal operation writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0x00); writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0x00); delay(25); // Delay a while to let the device stabilize
// Retrieve accelerometer and gyro factory Self-Test Code from USR_Reg selfTest[0] = readByte(MPU9250_ADDRESS, SELF_TEST_X_ACCEL); // X-axis accel self-test results selfTest[1] = readByte(MPU9250_ADDRESS, SELF_TEST_Y_ACCEL); // Y-axis accel self-test results selfTest[2] = readByte(MPU9250_ADDRESS, SELF_TEST_Z_ACCEL); // Z-axis accel self-test results selfTest[3] = readByte(MPU9250_ADDRESS, SELF_TEST_X_GYRO); // X-axis gyro self-test results selfTest[4] = readByte(MPU9250_ADDRESS, SELF_TEST_Y_GYRO); // Y-axis gyro self-test results selfTest[5] = readByte(MPU9250_ADDRESS, SELF_TEST_Z_GYRO); // Z-axis gyro self-test results
// Retrieve factory self-test value from self-test code reads factoryTrim[0] = (float)(2620/1<<FS)(pow( 1.01 , ((float)selfTest[0] - 1.0) )); // FT[Xa] factory trim calculation factoryTrim[1] = (float)(2620/1<<FS)(pow( 1.01 , ((float)selfTest[1] - 1.0) )); // FT[Ya] factory trim calculation factoryTrim[2] = (float)(2620/1<<FS)(pow( 1.01 , ((float)selfTest[2] - 1.0) )); // FT[Za] factory trim calculation factoryTrim[3] = (float)(2620/1<<FS)(pow( 1.01 , ((float)selfTest[3] - 1.0) )); // FT[Xg] factory trim calculation factoryTrim[4] = (float)(2620/1<<FS)(pow( 1.01 , ((float)selfTest[4] - 1.0) )); // FT[Yg] factory trim calculation factoryTrim[5] = (float)(2620/1<<FS)(pow( 1.01 , ((float)selfTest[5] - 1.0) )); // FT[Zg] factory trim calculation
// Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response // To get percent, must multiply by 100 for (int i = 0; i < 3; i++) { destination[i] = 100.0f((float)(aSTAvg[i] - aAvg[i]))/factoryTrim[i] - 100.0f; // Report percent differences destination[i+3] = 100.0f((float)(gSTAvg[i] - gAvg[i]))/factoryTrim[i+3] - 100.0f; // Report percent differences }
}
// simple function to scan for I2C devices on the bus void I2Cscan() { // scan for i2c devices byte error, address; int nDevices;
Serial.println("Scanning...");
nDevices = 0; for(address = 1; address < 127; address++ ) { // The i2c_scanner uses the return value of // the Write.endTransmisstion to see if // a device did acknowledge to the address. Wire.beginTransmission(address); error = Wire.endTransmission();
if (error == 0) { Serial.print("I2C device found at address 0x"); if (address<16) Serial.print("0"); Serial.print(address,HEX); Serial.println(" !"); nDevices++; } else if (error==4) { Serial.print("Unknown error at address 0x"); if (address<16) Serial.print("0"); Serial.println(address,HEX); }
} if (nDevices == 0) Serial.println("No I2C devices found\n"); else Serial.println("done\n"); }
// I2C read/write functions for the MPU9250 sensors
void writeByte(uint8_t address, uint8_t subAddress, uint8_t data) { Wire.beginTransmission(address); // Initialize the Tx buffer Wire.write(subAddress); // Put slave register address in Tx buffer Wire.write(data); // Put data in Tx buffer Wire.endTransmission(); // Send the Tx buffer }
uint8_t readByte(uint8_t address, uint8_t subAddress) { uint8_t data = 0; //
data
will store the register data Wire.beginTransmission(address); // Initialize the Tx buffer Wire.write(subAddress); // Put slave register address in Tx buffer Wire.endTransmission(false); // Send the Tx buffer, but send a restart to keep connection alive Wire.requestFrom(address, 1); // Read two bytes from slave register address on MPU9250 data = Wire.read(); // Fill Rx buffer with result return data; // Return data read from slave register }void readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest) { Wire.beginTransmission(address); // Initialize the Tx buffer Wire.write(subAddress); // Put slave register address in Tx buffer Wire.endTransmission(false); // Send the Tx buffer, but send a restart to keep connection alive uint8_t i = 0; Wire.requestFrom(address, count); // Read bytes from slave register address while (Wire.available()) { dest[i++] = Wire.read(); } // Put read results in the Rx buffer }
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKSOF5G5KQAZ7EOYMV3QP2KLLA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB4UOGI#issuecomment-544818969, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKUZDPKYVTL5NRLXHKDQP2KLLANCNFSM4JDC3OVQ .
I get the idea. Increase gyro sampling rate to get better resolution w.r.t. time. Then complete as many madgwick iterations as possible in the time interval between two consecutive sets of gyro data. But how do we ensure that no gyro data set is skipped during the execution of the madgwick for loop? I tried to time the inter arrival duration but it is less than microsecond. So can't be timed using Arduino api. I understand that if the Accel and gyro sampling rate is set at 1khz then they should arrive every one micro second. So I guess I need to see how many madgwick iterations can be run in one microsecond. But again I can only time it over a large number of iterations
testing. At 1 kHz gyro sample rate you have 1 msec to do all the iterations. So if the mcu can run at 50kHz rate as the STM32L4 can, you could complete 50 iterations.
On Tue, Oct 22, 2019 at 1:01 PM shomedas notifications@github.com wrote:
I get the idea. Increase gyro sampling rate to get better resolution w.r.t. time. Then complete as many madgwick iterations as possible in the time interval between two consecutive sets of gyro data. But how do we ensure that no gyro data set is skipped during the execution of the madgwick for loop?
— You are receiving this because you commented.
Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKVCVRIBYFOLIJSVJYTQP5L2XA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB7AEKY#issuecomment-545129003, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKRIGTCCXAH34ET4T6DQP5L2XANCNFSM4JDC3OVQ .
I measured the time taken between two consecutive set of data packets arriving. Strangely I found that new data arrives every I microsecond, not 1 milisecond
void loop()
{
if(newData == true) { // On interrupt, read data
newData = false; // reset newData flag
Now = micros();
deltat = (Now - lastUpdate);
Serial.print("time between two data sets= "); Serial.println(deltat);
lastUpdate = micros();
}
}
Output :
MPU9250 initialized for active data mode....
AK8963 I AM 48 I should be 48
AK8963 initialized for active data mode....
X-Axis sensitivity adjustment value 1.18
Y-Axis sensitivity adjustment value 1.18
Z-Axis sensitivity adjustment value 1.14
time between consecutive data packets in microsec= 13466409.00
time between consecutive data packets in microsec= 4936.00
time between consecutive data packets in microsec= 4942.00
time between consecutive data packets in microsec= 1.00
time between consecutive data packets in microsec= 1.00
time between consecutive data packets in microsec= 1.00
time between consecutive data packets in microsec= 1.00
Not possible, sorry..something in your sketch is wrong.
On Tue, Oct 22, 2019 at 8:16 PM shomedas notifications@github.com wrote:
I measured the time taken between two consecutive set of data packets arriving. Strangely I found that new data arrives every I microsecond, not 1 milisecond
void loop() { if(newData == true) { // On interrupt, read data
newData = false; // reset newData flag Now = micros(); deltat = (Now - lastUpdate); Serial.print("time between two data sets= "); Serial.println(deltat); lastUpdate = micros(); }
}
Output :
MPU9250 initialized for active data mode.... AK8963 I AM 48 I should be 48 AK8963 initialized for active data mode.... X-Axis sensitivity adjustment value 1.18 Y-Axis sensitivity adjustment value 1.18 Z-Axis sensitivity adjustment value 1.14 time between consecutive data packets in microsec= 13466409.00 time between consecutive data packets in microsec= 4936.00 time between consecutive data packets in microsec= 4942.00 time between consecutive data packets in microsec= 1.00 time between consecutive data packets in microsec= 1.00 time between consecutive data packets in microsec= 1.00 time between consecutive data packets in microsec= 1.00
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKX636I6ZRGPURJCM2LQP66XLA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB74ZJY#issuecomment-545246375, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKQXPLYTJBTD4P3EF2DQP66XLANCNFSM4JDC3OVQ .
For the above timing I have used your ESP32 code from https://github.com/kriswiner/ESP32/tree/master/MPU9250_MS5637. I have removed 5637 related code. Only other change is
writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set sample rate to 1 kHz
The loop contains ONLY timing code as
void loop()
{
if(newData == true) { // On interrupt, read data
newData = false; // reset newData flag
Now = micros();
deltat = (Now - lastUpdate);
Serial.print("time between two data sets= "); Serial.println(deltat);
lastUpdate = micros();
}
}
If you suggest I can attach the entire code here.
My sketch does not calculate time between interrupts. If you change the sketch to do this you should see about 1/1000 Hz ~ 1 millisecond. It is simply not possible for the interrupt to trigger every microsecond. Something is not correct in your sketch.
Use an oscilloscope and verify that the interrupt is triggering at ~1 kHz please...
On Tue, Oct 22, 2019 at 8:48 PM shomedas notifications@github.com wrote:
For the above timing I have used your ESP32 code from https://github.com/kriswiner/ESP32/tree/master/MPU9250_MS5637. I have removed 5637 related code. Only other change is
writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set sample rate to 1 kHz
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKWMTVLADKW43OCWW5DQP7CPTA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB76MVI#issuecomment-545252949, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKVL2C75CORAGNREP2LQP7CPTANCNFSM4JDC3OVQ .
Ok. I will use the oscilloscope to check
If this is your main loop:
void loop() { if(newData == true) { // On interrupt, read data
newData = false; // reset newData flag
Now = micros();
deltat = (Now - lastUpdate);
Serial.print("time between two data sets= "); Serial.println(deltat);
lastUpdate = micros();
}
}
How are you clearing the interrupt?
On Tue, Oct 22, 2019 at 9:11 PM Tlera Corporation tleracorp@gmail.com wrote:
My sketch does not calculate time between interrupts. If you change the sketch to do this you should see about 1/1000 Hz ~ 1 millisecond. It is simply not possible for the interrupt to trigger every microsecond. Something is not correct in your sketch.
Use an oscilloscope and verify that the interrupt is triggering at ~1 kHz please...
On Tue, Oct 22, 2019 at 8:48 PM shomedas notifications@github.com wrote:
For the above timing I have used your ESP32 code from https://github.com/kriswiner/ESP32/tree/master/MPU9250_MS5637. I have removed 5637 related code. Only other change is
writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set sample rate to 1 kHz
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKWMTVLADKW43OCWW5DQP7CPTA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEB76MVI#issuecomment-545252949, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKVL2C75CORAGNREP2LQP7CPTANCNFSM4JDC3OVQ .
To clear interrupt I added readMPU9250Data(MPU9250Data); // INT cleared on any read
But the timing results Now report 5000microseconds, not 1000microseconds. Which would be correct if the sampling frequency was 200Hz. But SMPLRT_DIV is set at 0x00, meaning the sampling rate should be 1Khz
The loop is now
void loop()
{
if(newData == true) { // On interrupt, read data
Now = micros();
newData = false; // reset newData flag
readMPU9250Data(MPU9250Data); // INT cleared on any read
deltat = ((Now - lastUpdate));
Serial.print("time between consecutive data packets in microsec= "); Serial.println(deltat);
lastUpdate = Now;
}
}
I tried modifying SMPLRT_DIV to 0x00, 0x01. But the interval at which the data arrives stays at 5000microsecs which implies a 200Hz data update rate. How to modify the registers to be able to get 1Khz sampling rate i.e. to get interrupts at 1Khz rate. SMPLRT_DIV works depending on FCHOICE and FCHOICE_b. They need to be set correctly. However the default scaling should be 1 i.e. no scaling, which would keep the sampling frequency at 1Khz itself even without modifying the SMPLRT_DIV
Please check the data sheet.
On Tue, Oct 22, 2019 at 10:02 PM shomedas notifications@github.com wrote:
I tried modifying SMPLRT_DIV to 0x00, 0x01. But the interval at which the data arrives stays at 5000microsecs which implies a 200Hz data update rate. How to modify the registers to be able to get 1Khz sampling rate i.e. to get interrupts at 1Khz rate. SMPLRT_DIV works depending on FCHOICE and FCHOICE_b. They need to be set correctly. However the default scaling should be 1 i.e. no scaling, which would keep the sampling frequency at 1Khz itself even without modifying the SMPLRT_DIV
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKROBXD3L3SKA7QRSDDQP7LHLA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOECAB7XY#issuecomment-545267679, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKVOZJCTGYHPMEXJCX3QP7LHLANCNFSM4JDC3OVQ .
yes doing that now.
You might try increasing the bandwidth since setting a low bandwidth amounts to internal averaging of the data so this might be changing the effective simple rate. Although I seem to recall measuring the interrupt rate at 200 Hz sample rate and 41 Hz bandwidth and still seeing 200 Hz or so on the interrupt rate. So unlikely the problem is with the sensor. Can you verify that the interrupt triggers at 200 Hz with an O scope when you have the sample rate set to 1 kHz?
On Tue, Oct 22, 2019 at 10:32 PM shomedas notifications@github.com wrote:
yes doing that now.
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/kriswiner/MPU9250/issues/396?email_source=notifications&email_token=ABTDLKSAW5AU7ZGXJH3VQNTQP7OYVA5CNFSM4JDC3OV2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOECADSXA#issuecomment-545274204, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABTDLKRXHZVFMOJYGJVBMETQP7OYVANCNFSM4JDC3OVQ .
I had found that there is a delay(a few seconds) in the convergence of the heading quaternion when the IMU is moved randomly or fast. So I have ported the sensor fusion part of your code(the for loop having the madgwick update) to my desktop to get higher sensor fusion rates. I grab the accelerometer, gyroscope and the magnetometer readings from the MPU9250 using an ESP32 using the remaining part of your code. I calibrate the data in my desktop.
My question is what parameters do I need to change to attain faster convergence when I move around the IMU. I read from your git forum that accelerometer and gyroscope need to be sampled at 1Khz with 100 Hz Low Pass Filter, while magnetometer is to be left at 100Hz. I made the following changes in initMPU9250 function of your code
SMPLRT_DIV : changed it to 0x00 from 0x04 to set the accelerometer and gyroscope sampling rate at 1Khz writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x02)
DLPF_CFG changed it to 0x02 from 0x03 to set the gyro bandwidth to 92Hz writeByte(MPU9250_ADDRESS, CONFIG, 0x02)
c=c|0x02 ; // changed it to 0x02 from 0x03 to set the gyro bandwidth to 92Hz writeByte(MPU9250_ADDRESS, CONFIG, ACCEL_CONFIG2,c)
What other changes do I need to do? Do I need to change the i2c frequency to 1Mhz. Do I need to change the i2c resistance for operating at 1Mhz What about the baud rate between the ESP32 and the desktop?