search

lfantoniosi / tn_vdp

Tang Nano 9K TMS 9118A VDP
BSD 3-Clause "New" or "Revised" License
120 stars 23 forks source link

Go Win Programmer Error #13

Closed AxelAhlborn closed 1 year ago

AxelAhlborn commented 1 year ago

Hi, installed GoWin IDE Education 1.9.8.11 Build 21024 Use GoWin Programmer Series GW1NR, Device GW1NR-9C Embedded Flash Mode Erase, Program, Verify File E:/Tools/tn9k/tn_vdp.fs

Output of Gowin Programmer: Info: Cable found: USB Debugger A/0/545/null (USB location:545) Info: Cost 0.56 second(s) :
Info: Target Cable: USB Debugger A/0/545/null@2.5MHz Info: Operation "embFlash Erase,Program,Verify" is starting on device-1... Error: Verify Failed at 0 Error: Verify Failed! Info: Cost 10.84 second(s) :

Need some help 😇

Greetings Axel

lfantoniosi commented 1 year ago

Did you choose flash generic? If so check:

Reboot pc Re-install drivers Check usb cable

There sre so many things

On Wed, Jul 12, 2023 at 5:40 AM AxelAhlborn @.***> wrote:

Hi, installed GoWin IDE Education 1.9.8.11 Build 21024 Use GoWin Programmer Series GW1NR, Device GW1NR-9C Embedded Flash Mode Erase, Program, Verify File E:/Tools/tn9k/tn_vdp.fs

Output of Gowin Programmer: Info: Cable found: USB Debugger A/0/545/null (USB location:545) Info: Cost 0.56 second(s) : Info: Target Cable: USB Debugger @.*** Info: Operation "embFlash Erase,Program,Verify" is starting on device-1... Error: Verify Failed at 0 Error: Verify Failed! Info: Cost 10.84 second(s) :

Need some help 😇

Greetings Axel

— Reply to this email directly, view it on GitHub https://github.com/lfantoniosi/tn_vdp/issues/13, or unsubscribe https://github.com/notifications/unsubscribe-auth/ACCJWUYWJSUKGN4VRO3LBO3XP2LK7ANCNFSM6AAAAAA2HNW5CA . You are receiving this because you are subscribed to this thread.Message ID: @.***>

-- Luis Felipe Antoniosi

AxelAhlborn commented 1 year ago

Yes, I did. I tested on 2 PC´s. Every device shows an error if you choose "verify". If you choose only "Erase , Program" it looks good. No erro (because verify is missing...) r. But I get no Testscreen on HDMI

lfantoniosi commented 1 year ago

Which one? Tang 20k has no test screeb

On Wed, Jul 12, 2023 at 8:30 AM AxelAhlborn @.***> wrote:

Yes, I did. I tested on 2 PC´s. Every device shows an error if you choose "verify". If you choose only "Erase , Program" it looks good. No erro (because verify is missing...) r. But I get no Testscreen on HDMI

— Reply to this email directly, view it on GitHub https://github.com/lfantoniosi/tn_vdp/issues/13#issuecomment-1632758645, or unsubscribe https://github.com/notifications/unsubscribe-auth/ACCJWU6V7AREFNTTWC3ZJELXP27K3ANCNFSM6AAAAAA2HNW5CA . You are receiving this because you commented.Message ID: @.***>

-- Luis Felipe Antoniosi

lfantoniosi commented 1 year ago

Dont verify i don’t verify either.

Check sipeed website for usb issues. It can’t help you here i had once to delete every trace of ftdi drivers in my win 11. Try a fresh new installation.

Also it does not work from virtual machines. Very picky.

On Wed, Jul 12, 2023 at 8:30 AM AxelAhlborn @.***> wrote:

Yes, I did. I tested on 2 PC´s. Every device shows an error if you choose "verify". If you choose only "Erase , Program" it looks good. No erro (because verify is missing...) r. But I get no Testscreen on HDMI

— Reply to this email directly, view it on GitHub https://github.com/lfantoniosi/tn_vdp/issues/13#issuecomment-1632758645, or unsubscribe https://github.com/notifications/unsubscribe-auth/ACCJWU6V7AREFNTTWC3ZJELXP27K3ANCNFSM6AAAAAA2HNW5CA . You are receiving this because you commented.Message ID: @.***>

-- Luis Felipe Antoniosi

AxelAhlborn commented 1 year ago

That's OK. I use the tn9k with tn vdp V1. The problem I have with this is that I don't know if the flash was successful or not because the TN9K has the R1 bridge problem over HDMI. If the bridge is not set, some HDMI devices cannot display a picture. So I don't know if it's one thing or the other. I will create the vga board to test with vga. Greetings Axel