search

linux4wilc / firmware

Firmware binaries for Microchip ATWILC Wireless Devices (ATWILC1000 & ATWILC3000)
https://www.microchip.com/wwwproducts/en/ATWILC1000
Other
15 stars 9 forks source link

send_ntwrk_info: Failed to alloc memory for beacon/probe rsp #3

Open HDC67 opened 5 years ago

HDC67 commented 5 years ago

Hardware: SAMA5D4Xplained dev board + ATWILC1000-SD (rev 4) dev board

Software: wilc_demo 15.2RC1 from: https://github.com/linux4wilc/wilc_demo/tree/009b36048d18ffb64b2140eeecd0194cc21cbfd4

Updated firmware to 15.2RC3 firmware for this one:

# cat /etc/wpa_supplicant.conf
ctrl_interface=/run/wpa_supplicant
ctrl_interface_group=0

network={
ssid="AP"
psk="01234567"
}

There is no "AP" access point in the vicinity i.e. the unit has nothing to connect to. There are quite a few other APs around though as you can see in the log.

modprobe wilc-sdio
ifconfig wlan0 up
/usr/sbin/wpa_supplicant -Dnl80211 -iwlan0 -c /etc/wpa_supplicant.conf -B

firmware log has numerous memory allocation errors - this can't be good right:

e.g. all these occurr together in a short space of time.

(5822)mem_alloc: no free chunks in the found subpool[6][596][3]
(5823)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5823)mem_alloc: no free chunks in the found subpool[6][596][3]
(5824)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5824)cfg_bcn_local_mem_alloc(): req size > max beacon_cfg size
(5825)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5826)mem_alloc: no free chunks in the found subpool[6][596][3]
(5827)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5852)mem_alloc: no free chunks in the found subpool[6][596][3]
(5853)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp

Full log:

(0)Efuse_read: bank_idx = 0
(0)Efuse_read: MAC addr (used=1) = f8:f0:05:f1:48:66
(0)Efuse_read: Freq Off (used=1) = 32556
(0)Efuse_read: PA gain (used=0) = 0
>> Slp clk src <= Int. osc
chipid = 1003a0
turn on 3fff1fd 1ef5ff
(0)[set_mac_addr] mac address = f8:f0:5:f1:48:66
(0)Set mac handler mac address i=1
(0)MAC 1
(0)[set_mac_addr] mac address = fa:f0:5:f1:48:66
(0)Set mac handler mac address i=0
(0)MAC 0
>>>>>> SDIO <<<<<<<<<<
(0)------------------------------------
(0)IP version information
(0)------------------------------------
(0)MAC Hardware version : 0.1.04.0E.00
(1)MAC Firmware version : WILC_WIFI_FW_REL_15_2_RC3 Build: 10924
(1)RF Version: 01.1
(2)Built at Jan 11 2019 17:19:55
(2)------------------------------------
(2)Sent MAC status: MAC_DISCONNECTED host 0 , reason = 1 , code = 0
(67)Got mac handler by driver handler i=0
(67)[CFG]: type(Q), id(00000000), len(2)
(70)Got mac handler by driver handler i=0
(70)[CFG]: type(W), id(00000001), len(255)
(71)

>>Setting interface operation mode 2 on mac 43cc!!!!!!

set_802_11I_mode(): input val= 0
(71)Set mac handler BSSID i=0
(72)
Setting PM to 0

set_802_11I_mode(): input val= 0
(72)End Of Driver Configuration Messages
(GP_REG)USE PMU
->Use patched Gain Settings
(73)Setting Tx power to 18
(GP_REG)USE PMU
(73)Setting Tx power to 18
(74)[CFG]: type(W), id(00000002), len(9)
(75)[Parese Write]: id (00003079)
(75)Set WLAN_IFC[STA] driver handler 1
(75)[set_mac_addr] mac address = f8:f0:5:f1:48:66
(76)Set mac handler mac address i=0
(76)MAC 0
(76)[set_mac_addr] mac address = fa:f0:5:f1:48:66
(77)Set mac handler mac address i=1
(77)MAC 1
(77)42c0, 1
42dc, 0
(78)Got mac handler by driver handler i=0
(78)[CFG]: type(W), id(00000003), len(8)
(78)[Parese Write]: id (00002086)
(79)

>>Setting interface operation mode 2 on mac 43cc!!!!!!

set_802_11I_mode(): input val= 0
(80)Set mac handler BSSID i=0
(80)Got mac handler by driver handler i=0
(81)[CFG]: type(Q), id(00000004), len(2)
(93)Got mac handler by driver handler i=0
(93)[CFG]: type(W), id(00000005), len(25)
(93)[Parese Write]: id (0000408b)
(94)Got mac handler by driver handler i=0
(94)[CFG]: type(W), id(00000006), len(5)
(95)[Parese Write]: id (0000000b)
(95)
Setting PM to 0

(96)Got mac handler by driver handler i=0
(96)[CFG]: type(W), id(00000007), len(31)
(97)[Parese Write]: id (0000408b)
(97)Got mac handler by driver handler i=0
(98)[CFG]: type(W), id(00000008), len(37)
(98)[Parese Write]: id (0000408b)
(295)Got mac handler by driver handler i=0
(295)[CFG]: type(W), id(00000009), len(43)
(295)[Parese Write]: id (0000408b)
(5732)Got mac handler by driver handler i=0
(5732)[CFG]: type(Q), id(0000000a), len(2)
(5733)Got mac handler by driver handler i=0
(5734)[CFG]: type(Q), id(0000000b), len(2)
(5736)Got mac handler by driver handler i=0
(5736)[CFG]: type(Q), id(0000000c), len(2)
(5737)Got mac handler by driver handler i=0
(5738)[CFG]: type(Q), id(0000000d), len(2)
(5741)Got mac handler by driver handler i=0
(5741)[CFG]: type(W), id(0000000e), len(8)
(5741)[Parese Write]: id (00003084)
FRAME REG :1
(5744)Got mac handler by driver handler i=0
(5745)[CFG]: type(W), id(0000000f), len(8)
(5745)[Parese Write]: id (00003084)
FRAME REG :1
(5750)Got mac handler by driver handler i=0
(5750)[CFG]: type(W), id(00000010), len(8)
(5751)[Parese Write]: id (00003084)
FRAME REG :1
(5753)Got mac handler by driver handler i=0
(5753)[CFG]: type(W), id(00000011), len(8)
(5753)[Parese Write]: id (00003084)
FRAME REG :1
(5755)Got mac handler by driver handler i=0
(5756)[CFG]: type(W), id(00000012), len(8)
(5756)[Parese Write]: id (00003084)
FRAME REG :1
(5760)Got mac handler by driver handler i=0
(5761)[CFG]: type(W), id(00000013), len(8)
(5761)[Parese Write]: id (00003084)
FRAME REG :1
(5762)Got mac handler by driver handler i=0
(5762)[CFG]: type(W), id(00000014), len(8)
(5763)[Parese Write]: id (00003084)
FRAME REG :1
(5764)Got mac handler by driver handler i=0
(5764)[CFG]: type(W), id(00000015), len(8)
(5764)[Parese Write]: id (00003084)
FRAME REG :1
(5765)Got mac handler by driver handler i=0
(5766)[CFG]: type(W), id(00000016), len(8)
(5766)[Parese Write]: id (00003084)
FRAME REG :1
(5767)Got mac handler by driver handler i=0
(5768)[CFG]: type(W), id(00000017), len(8)
(5768)[Parese Write]: id (00003084)
FRAME REG :1
(5769)Got mac handler by driver handler i=0
(5769)[CFG]: type(W), id(00000018), len(8)
(5770)[Parese Write]: id (00003084)
FRAME REG :1
(5771)Got mac handler by driver handler i=0
(5771)[CFG]: type(W), id(00000019), len(8)
(5771)[Parese Write]: id (00003084)
FRAME REG :1
(5772)Got mac handler by driver handler i=0
(5773)[CFG]: type(W), id(0000001a), len(8)
(5773)[Parese Write]: id (00003084)
FRAME REG :1
(5774)Got mac handler by driver handler i=0
(5774)[CFG]: type(W), id(0000001b), len(8)
(5775)[Parese Write]: id (00003084)
FRAME REG :1
(5776)Got mac handler by driver handler i=0
(5776)[CFG]: type(W), id(0000001c), len(8)
(5776)[Parese Write]: id (00003084)
FRAME REG :1
(5777)Got mac handler by driver handler i=0
(5778)[CFG]: type(W), id(0000001d), len(8)
(5778)[Parese Write]: id (00003084)
FRAME REG :1
(5779)Got mac handler by driver handler i=0
(5780)[CFG]: type(W), id(0000001e), len(8)
(5780)[Parese Write]: id (00003084)
FRAME REG :1
(5781)Got mac handler by driver handler i=0
(5781)[CFG]: type(Q), id(0000001f), len(2)
(5799)Got mac handler by driver handler i=0
(5799)[CFG]: type(W), id(00000020), len(165)
(5800)[Parese Write]: id (00003997)
(5800)[Parese Write]: id (00004085)
(5800)[Parese Write]: id (00000007)
(5801)[Parese Write]: id (00004084)
(5801)[Parese Write]: id (0000001e)
(5801)req scan source=1
(5802)initiate scan
(5802)mac state wlan0 -- 3
>> Slp clk src <= Int. osc
(5822)mem_alloc: no free chunks in the found subpool[6][596][3]
(5823)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5823)mem_alloc: no free chunks in the found subpool[6][596][3]
(5824)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5824)cfg_bcn_local_mem_alloc(): req size > max beacon_cfg size
(5825)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5826)mem_alloc: no free chunks in the found subpool[6][596][3]
(5827)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5852)mem_alloc: no free chunks in the found subpool[6][596][3]
(5853)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(5860)mac state wlan0 -- 4
(5860)mac state wlan0 -- 0
(5860)send_scan_complete_to_host: Sending  Scan Complete Notification
(6391)Got mac handler by driver handler i=0
(6391)[CFG]: type(W), id(00000021), len(165)
(6392)[Parese Write]: id (00003997)
(6392)[Parese Write]: id (00004085)
(6392)[Parese Write]: id (00000007)
(6393)[Parese Write]: id (00004084)
(6393)[Parese Write]: id (0000001e)
(6393)req scan source=1
(6393)initiate scan
(6394)mac state wlan0 -- 3
(6414)cfg_bcn_local_mem_alloc(): req size > max beacon_cfg size
(6415)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(6417)cfg_bcn_local_mem_alloc(): req size > max beacon_cfg size
(6418)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(6450)mac state wlan0 -- 4
(6450)mac state wlan0 -- 0
(6450)send_scan_complete_to_host: Sending  Scan Complete Notification
(7028)Got mac handler by driver handler i=0
(7029)[CFG]: type(W), id(00000022), len(165)
(7029)[Parese Write]: id (00003997)
(7030)[Parese Write]: id (00004085)
(7030)[Parese Write]: id (00000007)
(7030)[Parese Write]: id (00004084)
(7030)[Parese Write]: id (0000001e)
(7031)req scan source=1
(7031)initiate scan
(7031)mac state wlan0 -- 3
(7051)cfg_bcn_local_mem_alloc(): req size > max beacon_cfg size
(7051)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(7087)mac state wlan0 -- 4
(7087)mac state wlan0 -- 0
(7087)send_scan_complete_to_host: Sending  Scan Complete Notification
(7652)Got mac handler by driver handler i=0
(7652)[CFG]: type(W), id(00000023), len(165)
(7653)[Parese Write]: id (00003997)
(7653)[Parese Write]: id (00004085)
(7653)[Parese Write]: id (00000007)
(7654)[Parese Write]: id (00004084)
(7654)[Parese Write]: id (0000001e)
(7654)req scan source=1
(7654)initiate scan
(7655)mac state wlan0 -- 3
(7676)cfg_bcn_local_mem_alloc(): req size > max beacon_cfg size
(7676)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(7703)mem_alloc: no free chunks in the found subpool[6][596][3]
(7704)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(7711)mac state wlan0 -- 4
(7711)mac state wlan0 -- 0
(7711)send_scan_complete_to_host: Sending  Scan Complete Notification
(8279)Got mac handler by driver handler i=0
(8280)[CFG]: type(W), id(00000024), len(165)
(8280)[Parese Write]: id (00003997)
(8281)[Parese Write]: id (00004085)
(8281)[Parese Write]: id (00000007)
(8281)[Parese Write]: id (00004084)
(8281)[Parese Write]: id (0000001e)
(8282)req scan source=1
(8282)initiate scan
(8282)mac state wlan0 -- 3
(8302)cfg_bcn_local_mem_alloc(): req size > max beacon_cfg size
(8302)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(8304)cfg_bcn_local_mem_alloc(): req size > max beacon_cfg size
(8305)send_ntwrk_info: Failed to alloc memory for beacon/probe rsp
(8338)mac state wlan0 -- 4
(8338)mac state wlan0 -- 0
(8338)send_scan_complete_to_host: Sending  Scan Complete Notification

syslog (for reference only really):


EEPROM: Loading AT24xx information ...
EEPROM: BoardName | [Revid] | VendorName
HW Info: The total size: 0xff isn't correct

EEPROM: Using default information

EEPROM: Board sn: 0x1012420 revision: 0x680820

HDMI SiI9022: Enter D3 Cold mode
NAND: ONFI flash detected
NAND: Manufacturer ID: 0x2c Chip ID: 0x34
NAND: Page Bytes: 4096, Spare Bytes: 224
NAND: ECC Correctability Bits: 8, ECC Sector Bytes: 512
NAND: Disable On-Die ECC
NAND: Initialize PMECC params, cap: 8, sector: 512
NAND: Image: Copy 0xa0000 bytes from 0x40000 to 0x26f00000
NAND: Done to load image
<debug_uart>

U-Boot 2017.03-linux4sam_5.6 (May 31 2018 - 12:57:41 -0700)

CPU: SAMA5D44
Crystal frequency:       12 MHz
CPU clock        :      600 MHz
Master clock     :      200 MHz
DRAM:  512 MiB
NAND:  512 MiB
MMC:   Atmel mci: 0
In:    serial
Out:   serial
Err:   serial
Net:   eth0: ethernet@f8020000
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x180000, size 0x817c
 33148 bytes read: OK

NAND read: device 0 offset 0x200000, size 0x3df7c8
 4061128 bytes read: OK
## Flattened Device Tree blob at 21000000
   Booting using the fdt blob at 0x21000000
   Loading Device Tree to 3f951000, end 3f95c17b ... OK

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 4.9.36 (adham@adham-Latitude-E7450) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 Thu May 31 13:04:12 MST 2018
CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt:Machine model: Atmel SAMA5D4 Xplained
cma: Reserved 64 MiB at 0x38000000
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs rw
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 444308K/524288K available (6144K kernel code, 196K rwdata, 1492K rodata, 1024K init, 193K bss, 14444K reserved, 65536K cma-reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xe0800000 - 0xff800000   ( 496 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc0700000   (7136 kB)
      .init : 0xc0900000 - 0xc0a00000   (1024 kB)
      .data : 0xc0a00000 - 0xc0a31220   ( 197 kB)
       .bss : 0xc0a31220 - 0xc0a61950   ( 194 kB)
NR_IRQS:16 nr_irqs:16 16
L2C-310 ID prefetch enabled, offset 2 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 128 kB
L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x36020000
clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 9556302164 ns
sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns
Console: colour dummy device 80x30
Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x20100000 - 0x20100058
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 256 (order: -1, 3072 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
AT91: Detected SoC family: sama5d4
AT91: Detected SoC: sama5d44, revision 0
gpio-at91 fc06a000.gpio: at address e0818000
gpio-at91 fc06b000.gpio: at address e081a000
gpio-at91 fc06c000.gpio: at address e081c000
gpio-at91 fc068000.gpio: at address e081e000
gpio-at91 fc06d000.gpio: at address e0831000
pinctrl-at91 ahb:apb:pinctrl@fc06a000: initialized AT91 pinctrl driver
clocksource: tcb_clksrc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 152900835740 ns
at_xdmac f0004000.dma-controller: 16 channels, mapped at 0xe0837000
at_xdmac f0014000.dma-controller: 16 channels, mapped at 0xe0839000
VDD MCI1: supplied by VCC 3V3
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
at91_i2c f8014000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
at91_i2c f8014000.i2c: AT91 i2c bus driver (hw version: 0x502).
media: Linux media interface: v0.10
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.22
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
clocksource: Switched to clocksource tcb_clksrc
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
workingset: timestamp_bits=30 max_order=17 bucket_order=0
io scheduler noop registered (default)
f8004000.serial: ttyS5 at MMIO 0xf8004000 (irq = 25, base_baud = 6250000) is a ATMEL_SERIAL
fc00c000.serial: ttyS0 at MMIO 0xfc00c000 (irq = 31, base_baud = 6250000) is a ATMEL_SERIAL
console [ttyS0] enabled
fc010000.serial: ttyS1 at MMIO 0xfc010000 (irq = 32, base_baud = 6250000) is a ATMEL_SERIAL
[drm] Initialized
brd: module loaded
loop: module loaded
atmel_nand_nfc 90000000.nfc: NFC is probed.
atmel_nand 80000000.nand: Using dma0chan2 for DMA transfers.
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc
nand: Micron MT29F4G08ABAEAWP
nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224
atmel_nand 80000000.nand: Use On Flash BBT
atmel_nand 80000000.nand: Cannot get PMECC lookup table offset, will build a lookup table in runtime.
atmel_nand 80000000.nand: minimum ECC: 8 bits in 512 bytes
atmel_nand 80000000.nand: Initialize PMECC params, cap: 8, sector: 512
atmel_nand 80000000.nand: Using NFC Sram read and write
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
8 cmdlinepart partitions found on MTD device atmel_nand
Creating 8 MTD partitions on "atmel_nand":
0x000000000000-0x000000040000 : "bootstrap"
0x000000040000-0x0000000c0000 : "uboot"
0x0000000c0000-0x000000100000 : "env"
0x000000100000-0x000000140000 : "env_redundant"
0x000000140000-0x000000180000 : "spare"
0x000000180000-0x000000200000 : "dtb"
0x000000200000-0x000000800000 : "kernel"
0x000000800000-0x000020000000 : "rootfs"
atmel_spi f8010000.spi: version: 0x221
atmel_spi f8010000.spi: Using dma0chan3 (tx) and dma0chan4 (rx) for DMA transfers
m25p80 spi32766.0: unrecognized JEDEC id bytes: 00, 00, 00
atmel_spi f8010000.spi: Atmel SPI Controller at 0xf8010000 (irq 26)
atmel_spi fc018000.spi: version: 0x221
atmel_spi fc018000.spi: Using dma0chan5 (tx) and dma0chan6 (rx) for DMA transfers
atmel_spi fc018000.spi: Atmel SPI Controller at 0xfc018000 (irq 33)
libphy: Fixed MDIO Bus: probed
CAN device driver interface
libphy: MACB_mii_bus: probed
Micrel KSZ8081 or KSZ8091 f8020000.etherne:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=f8020000.etherne:01, irq=175)
macb f8020000.ethernet eth0: Cadence GEM rev 0x00020120 at 0xf8020000 irq 29 (fc:c2:3d:0d:ac:e3)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-atmel: EHCI Atmel driver
atmel-ehci 600000.ehci: EHCI Host Controller
atmel-ehci 600000.ehci: new USB bus registered, assigned bus number 1
atmel-ehci 600000.ehci: irq 19, io mem 0x00600000
atmel-ehci 600000.ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 4.9.36 ehci_hcd
usb usb1: SerialNumber: 600000.ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-atmel: OHCI Atmel driver
at91_ohci 500000.ohci: failed to find sfr node
at91_ohci 500000.ohci: USB Host Controller
at91_ohci 500000.ohci: new USB bus registered, assigned bus number 2
at91_ohci 500000.ohci: irq 19, io mem 0x00500000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: USB Host Controller
usb usb2: Manufacturer: Linux 4.9.36 ohci_hcd
usb usb2: SerialNumber: at91
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver ftdi_sio
usbserial: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver pl2303
usbserial: USB Serial support registered for pl2303
rtc rtc0: alarm rollover not handled
rtc rtc0: invalid alarm value: 1900-1-1 0:0:0
at91_rtc fc0686b0.rtc: rtc core: registered fc0686b0.rtc as rtc0
at91_rtc fc0686b0.rtc: AT91 Real Time Clock driver.
i2c /dev entries driver
AT91: Starting after user reset
sama5d4_wdt fc068640.watchdog: initialized (timeout = 16 sec, nowayout = 0)
Bluetooth: HCI UART driver ver 2.3
Bluetooth: HCI UART protocol H4 registered
Bluetooth: HCI UART protocol BCSP registered
Bluetooth: HCI UART protocol LL registered
Bluetooth: HCI UART protocol ATH3K registered
Bluetooth: HCI UART protocol Three-wire (H5) registered
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
atmel_mci fc000000.mmc: reg property is missing for /ahb/apb/mmc@fc000000/wilc_sdio@0
atmel_mci fc000000.mmc: version: 0x600
atmel_mci fc000000.mmc: using dma0chan7 for DMA transfers
atmel_mci fc000000.mmc: Atmel MCI controller at 0xfc000000 irq 30, 1 slots
sdhci-pltfm: SDHCI platform and OF driver helper
ledtrig-cpu: registered to indicate activity on CPUs
atmel_aes fc044000.aes: version: 0x201
atmel_aes fc044000.aes: Atmel AES - Using dma1chan0, dma1chan1 for DMA transfers
atmel_sha fc050000.sha: version: 0x420
atmel_sha fc050000.sha: using dma1chan2 for DMA transfers
atmel_sha fc050000.sha: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
atmel_tdes fc04c000.tdes: version: 0x702
atmel_tdes fc04c000.tdes: using dma1chan3, dma1chan4 for DMA transfers
atmel_tdes fc04c000.tdes: Atmel DES/TDES
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
iio iio:device0: Resolution used: 10 bits
iio iio:device0: ADC Touch screen is disabled.
NET: Registered protocol family 10
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20161123 t)
can: netlink gateway (rev 20130117) max_hops=1
ubi0: default fastmap pool size: 100
ubi0: default fastmap WL pool size: 50
ubi0: attaching mtd7
random: fast init done
mmc0: new high speed SDIO card at address 0001
ubi0: scanning is finished
ubi0: attached mtd7 (name "rootfs", size 504 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 2012, bad PEBs: 4, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1986554931
ubi0: available PEBs: 0, total reserved PEBs: 2012, PEBs reserved for bad PEB handling: 36
input: gpio_keys as /devices/soc0/gpio_keys/input/input0
ubi0: background thread "ubi_bgt0d" started, PID 101
at91_rtc fc0686b0.rtc: setting system clock to 2012-01-01 00:15:34 UTC (1325376934)
ALSA device list:
  No soundcards found.
atmel_usart fc00c000.serial: using dma0chan8 for rx DMA transfers
atmel_usart fc00c000.serial: using dma0chan9 for tx DMA transfers
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 102
UBIFS (ubi0:0): recovery needed
random: crng init done
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS (ubi0:0): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
UBIFS (ubi0:0): FS size: 497745920 bytes (474 MiB, 1960 LEBs), journal size 9404416 bytes (8 MiB, 38 LEBs)
UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 42AB1827-036A-4DA8-BC22-AA80F1632338, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:12.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0900000 - c0a00000)
Starting logging: OK
Populating /dev using udev: /etc/init.d/S10udev: line 47: can't create /proc/sys/kernel/hotplug: nonexistent directory
udevd[118]: starting version 3.2.2
udevd[119]: starting eudev-3.2.2
atmel_usba_udc 400000.gadget: MMIO registers at 0xfc02c000 mapped at e0ae4000
atmel_usba_udc 400000.gadget: FIFO at 0x00400000 mapped at e9100000
done
Initializing random number generator... done.
Starting system message bus: Unknown username "pulse" in message bus configuration file
done
Starting network: Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Listening on LPF/eth0/fc:c2:3d:0d:ac:e3
Sending on   LPF/eth0/fc:c2:3d:0d:ac:e3
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
cat: can't open '/etc/resolv.conf.*': No such file or directory
OK
Starting radvd: done
[Jan 01 00:16:38] radvd (200): wlan0 not found: No such device
Starting sshd: OK
Starting DHCP server: FAIL

Welcome to Buildroot
buildroot login: root
# modprobe wilc-sdio
wilc_sdio: module is from the staging directory, the quality is unknown, you have been warned.
(unnamed net_device) (uninitialized): INFO [wilc_create_wiphy]Registering wifi device
(unnamed net_device) (uninitialized): INFO [wilc_wfi_cfg_alloc]Allocating wireless device
(unnamed net_device) (uninitialized): INFO [wilc_create_wiphy]Successful Registering
(unnamed net_device) (uninitialized): INFO [wilc_create_wiphy]Registering wifi device
(unnamed net_device) (uninitialized): INFO [wilc_wfi_cfg_alloc]Allocating wireless device
(unnamed net_device) (uninitialized): INFO [wilc_create_wiphy]Successful Registering
wilc_sdio mmc0:0001:1: WILC got 60 for gpio_reset
wilc_sdio mmc0:0001:1: WILC got 94 for gpio_chip_en
wilc_sdio mmc0:0001:1: WILC got 91 for gpio_irq
wifi_pm : 0
wifi_pm : 1
wilc_sdio mmc0:0001:1: Driver Initializing success
# ifconfig wlan0 up
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mac_open]MAC OPEN[d4738800] wlan0
WILC POWER UP
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_init_host_int]Host[d4738800][d45fc800]
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mac_open]*** re-init ***
wilc_sdio mmc0:0001:1 wlan0: INFO [wlan_init_locks]Initializing Locks ...
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_init]Initializing WILC_Wlan
wilc_sdio mmc0:0001:1: SDIO speed: 50000000
wilc_sdio mmc0:0001:1: chipid 001003a0
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_initialize]WILC Initialization done
wilc_sdio mmc0:0001:1 wlan0: INFO [init_irq]IRQ request succeeded IRQ-NUM= 137 on GPIO: 91
wilc_sdio mmc0:0001:1 wlan0: INFO [wlan_initialize_threads]Initializing Threads ...
wilc_sdio mmc0:0001:1 wlan0: INFO [wlan_initialize_threads]Creating kthread for transmission
wilc_sdio mmc0:0001:1 wlan0: INFO [wlan_initialize_threads]Creating kthread for Debugging
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_get_firmware]Detect chip WILC1000
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_get_firmware]loading firmware mchp/wilc1000_wifi_firmware.bin
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_get_firmware]WLAN firmware: mchp/wilc1000_wifi_firmware.bin
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_firmware_download]Downloading Firmware ...
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_firmware_download]Downloading firmware size = 135020
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_firmware_download]Offset = 119704
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_firmware_download]Offset = 135020
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_firmware_download]Download Succeeded
wilc_sdio mmc0:0001:1 wlan0: INFO [linux_wlan_start_firmware]Starting Firmware ...
wilc_sdio mmc0:0001:1: wilc_sdio_cmd52..failed, err(-84)
wilc_sdio mmc0:0001:1: Failed cmd 52, read reg (000000fc) ...
wilc_sdio mmc0:0001:1 wlan0: INFO [linux_wlan_start_firmware]Waiting for FW to get ready ...
wilc_sdio mmc0:0001:1 wlan0: INFO [linux_wlan_start_firmware]Firmware successfully started
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wlan_initialize]WILC Firmware Ver = WILC_WIFI_FW_REL_15_2_RC3 Build: 10924
wilc_sdio mmc0:0001:1 wlan0: INFO [linux_wlan_init_test_config]Start configuring Firmware
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mac_open]Mac address: f8:f0:05:f1:48:66
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Setting mcast List with count = 2.
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[0]: 33:33:0:0:0:1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[1]: 33:33:0:0:0:2
wilc_sdio mmc0:0001:1 wlan0: INFO [set_power_mgmt] Power save Enabled= 0 , TimeOut = -1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Setting mcast List with count = 3.
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[0]: 33:33:0:0:0:1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[1]: 33:33:0:0:0:2
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[2]: 1:0:5e:0:0:1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Setting mcast List with count = 4.
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[0]: 33:33:0:0:0:1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[1]: 33:33:0:0:0:2
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[2]: 1:0:5e:0:0:1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[3]: 33:33:ff:f1:48:66
# wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Setting mcast List with count = 5.
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[0]: 33:33:0:0:0:1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[1]: 33:33:0:0:0:2
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[2]: 1:0:5e:0:0:1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[3]: 33:33:ff:f1:48:66
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_set_multicast_list]Entry[4]: 33:33:ff:0:0:0
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***

# /usr/sbin/wpa_supplicant -Dnl80211 -iwlan0 -c /etc/wpa_supplicant.conf -B
Successfully initialized wpa_supplicant
wilc_sdio mmc0:0001:1 wlan0: INFO [get_tx_power]Got tx power 0
wilc_sdio mmc0:0001:1 wlan0: INFO [get_tx_power]Got tx power 0
wilc_sdio mmc0:0001:1 wlan0: INFO [get_tx_power]Got tx power 0
wilc_sdio mmc0:0001:1 wlan0: INFO [get_tx_power]Got tx power 0
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_mgmt_frame_register]Frame registering Frame Type: d0: Boolean: 1
wilc_sdio mmc0:0001:1 wlan0: INFO [get_tx_power]Got tx power 0
wilc_sdio mmc0:0001:1 wlan0: INFO [flush_pmksa]Flushing  PMKID key values
# wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Requested num of scan channel 14
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Scan Request IE len =  126
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Number of SSIDs 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wfi_cfg_alloc_fill_ssid]Received one NULL SSID
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Trigger Scan Request
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network SM01AP2 found
wilc_sdio mmc0:0001:1 wlan0: INFO [is_network_in_shadow]Starting Aging timer
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network Telstra Air found
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network baresquedata found
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_scan_complete_received]Scan notification received
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network .U308@Galleries-2G found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network FreedomShared@Galleries found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Update RSSI of FreedomShared@Galleries
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network arqus found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Scan Done[d4738800]
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Refreshing Scan ...
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]6 Network(s) found
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Requested num of scan channel 14
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Scan Request IE len =  126
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Number of SSIDs 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wfi_cfg_alloc_fill_ssid]Received one NULL SSID
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Trigger Scan Request
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network Ferro_2.4GHz found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network SM01AP2 found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network DIRECT-3F-HP OfficeJet Pro 8740 found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network TelstraE82DE9 found
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network arqus found
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_scan_complete_received]Scan notification received
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network BelongYUNKRMEE found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Scan Done[d4738800]
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Refreshing Scan ...
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]6 Network(s) found
wilc_sdio mmc0:0001:1 wlan0: INFO [remove_network_from_shadow]Number of cached networks: 10
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Requested num of scan channel 14
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Scan Request IE len =  126
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Number of SSIDs 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wfi_cfg_alloc_fill_ssid]Received one NULL SSID
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Trigger Scan Request
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network SM01AP2 found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network Telstra Air found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network .U308@Galleries-2G found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network FreedomShared@Galleries found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network .U408@Galleries-2G found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network FreedomShared@Galleries found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network DIRECT-3F-HP OfficeJet Pro 8740 found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network TelstraE82DE9 found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Update RSSI of DIRECT-3F-HP OfficeJet Pro 8740
wilc_sdio mmc0:0001:1 wlan0: INFO [debug_thread]*** Debug Thread Running ***
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_scan_complete_received]Scan notification received
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network BelongYUNKRMEE found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Scan Done[d4738800]
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Refreshing Scan ...
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]9 Network(s) found
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Requested num of scan channel 14
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Scan Request IE len =  126
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Number of SSIDs 1
wilc_sdio mmc0:0001:1 wlan0: INFO [wilc_wfi_cfg_alloc_fill_ssid]Received one NULL SSID
wilc_sdio mmc0:0001:1 wlan0: INFO [scan]Trigger Scan Request
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network SM01AP2 found
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Update RSSI of SM01AP2
wilc_sdio mmc0:0001:1 wlan0: INFO [cfg_scan_result]Network baresquedata found
AdhamAbozaeid commented 5 years ago

Hi @ShonkyCH Please open a salesforce ticket for this issue

Ezhik92 commented 4 years ago

@ShonkyCH I have the same problem. Did you solve it?

HDC67 commented 4 years ago

@ShonkyCH I have the same problem. Did you solve it?

On the release firmware? I'm not surprised they haven't fixed it, if so.

There is no fix that I'm aware of but I haven't monitored the module debug port recently to see if it was fixed. The firmware is completely closed source and undocumented so we have no idea what it really means and there there is little we can do but report it and wait. I report them and they might fix them.

But like the other issue, I just don't have the time to burn chasing down Microchip's bugs for them. Something like this should be fairly obvious in their internal testing.