search

lixuewei / rt-n56u

Automatically exported from code.google.com/p/rt-n56u
0 stars 0 forks source link

u679 on bell won't connect to internet #1301

Open GoogleCodeExporter opened 9 years ago

GoogleCodeExporter commented 9 years ago 
1. Novatel u679 internet stick connected to either USB port
2. Enable internet over usb (USB Application - Modem)

Expected to be able to connect to bell's cellular service. Don't get connected 
or any internet connection. u679's status indicator shows the "network 
available but not connected" light.

N56U router, 3.0.3.8-081 

No modem type is able to connect. APN is entered correctly (inet.bell.ca).

----------log file below----------
Jan  1 00:18:28 kernel: usb 1-1: USB disconnect, device number 13
Jan  1 00:18:29 kernel: cdc_ether 1-1:1.6: weth0: unregister 'cdc_ether' 
usb-rt3xxx-ehci-1, CDC Ethernet Device
Jan  1 00:18:34 kernel: eth3: ===> VirtualIF_close
Jan  1 00:18:34 RT-N56U: Hardware NAT/Routing: Enabled, IPoE/PPPoE offload 
[WAN]<->[LAN/WLAN]
Jan  1 00:18:34 RT-N56U: Hardware NAT/Routing: IPv4 UDP flow offload - OFF
Jan  1 00:18:34 RT-N56U: Hardware NAT/Routing: IPv6 routes offload - OFF
Jan  1 00:18:34 kernel: eth3: ===> VirtualIF_open
Jan  1 00:18:34 miniupnpd[1453]: shutting down MiniUPnPd
Jan  1 00:18:34 DHCP WAN Client: starting on eth3 ...
Jan  1 00:18:34 miniupnpd[1854]: version 1.8 started
Jan  1 00:18:34 miniupnpd[1854]: HTTP listening on port 18186
Jan  1 00:18:38 kernel: usb 1-2: new high speed USB device number 14 using 
rt3xxx-ehci
Jan  1 00:18:38 kernel: usb 1-2: New USB device found, idVendor=1410, 
idProduct=5059
Jan  1 00:18:38 kernel: usb 1-2: New USB device strings: Mfr=3, Product=2, 
SerialNumber=4
Jan  1 00:18:38 kernel: usb 1-2: Product: Novatel Wireless HSPA
Jan  1 00:18:38 kernel: usb 1-2: Manufacturer: Novatel Wireless, Inc.
Jan  1 00:18:38 kernel: usb 1-2: SerialNumber: 012798005387731
Jan  1 00:18:38 kernel: scsi2 : usb-storage 1-2:1.0
Jan  1 00:18:41 kernel: scsi 2:0:0:0: CD-ROM            NVTL     Mass Storage   
  2.31 PQ: 0 ANSI: 2
Jan  1 00:18:41 kernel: scsi 2:0:0:0: Attached scsi generic sg0 type 5
Jan  1 00:18:41 kernel: sr0: scsi-1 drive
Jan  1 00:18:41 kernel: cdrom: Uniform CD-ROM driver Revision: 3.20
Jan  1 00:18:41 kernel: sr 2:0:0:0: Attached scsi CD-ROM sr0
Jan  1 00:18:42 kernel: cdrom: Uniform CD-ROM driver unloaded
Jan  1 00:18:43 kernel: usb 1-2: USB disconnect, device number 14
Jan  1 00:18:43 kernel: usb 1-2: new high speed USB device number 15 using 
rt3xxx-ehci
Jan  1 00:18:44 kernel: usb 1-2: config 1 has an invalid interface number: 6 
but max is 5
Jan  1 00:18:44 kernel: usb 1-2: config 1 has an invalid interface number: 7 
but max is 5
Jan  1 00:18:44 kernel: usb 1-2: config 1 has no interface number 4
Jan  1 00:18:44 kernel: usb 1-2: config 1 has no interface number 5
Jan  1 00:18:44 kernel: usb 1-2: New USB device found, idVendor=1410, 
idProduct=7031
Jan  1 00:18:44 kernel: usb 1-2: New USB device strings: Mfr=4, Product=3, 
SerialNumber=5
Jan  1 00:18:44 kernel: usb 1-2: Product: Novatel Wireless HSPA
Jan  1 00:18:44 kernel: usb 1-2: Manufacturer: Novatel Wireless, Inc.
Jan  1 00:18:44 kernel: usb 1-2: SerialNumber: 012798005387731
Jan  1 00:18:44 kernel: cdc_ether 1-2:1.6: weth0: register 'cdc_ether' at 
usb-rt3xxx-ehci-2, CDC Ethernet Device, 00:a0:c6:00:00:00
Jan  1 00:18:49 usb modem hotplug: try autorun modem wan connection...
Jan  1 00:18:49 stop_wan(): raise DHCP release event
Jan  1 00:18:50 kernel: eth3: ===> VirtualIF_close
Jan  1 00:18:50 RT-N56U: Hardware NAT/Routing: Enabled, IPoE/PPPoE offload 
[WAN]<->[LAN/WLAN]
Jan  1 00:18:50 RT-N56U: Hardware NAT/Routing: IPv4 UDP flow offload - OFF
Jan  1 00:18:50 RT-N56U: Hardware NAT/Routing: IPv6 routes offload - OFF
Jan  1 00:18:50 kernel: eth3: ===> VirtualIF_open
Jan  1 00:18:50 dnsmasq[477]: read /etc/hosts - 3 addresses
Jan  1 00:18:50 dnsmasq[477]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan  1 00:18:50 dnsmasq[477]: using nameserver 8.8.8.8#53
Jan  1 00:18:50 kernel: cdc_ether 1-2:1.6: weth0: CDC: unexpected notification 
01!
Jan  1 00:18:50 DHCP WAN Client: starting on weth0 ...

Original issue reported on code.google.com by dreadwin...@gmail.com on 29 Jul 2014 at 12:50

GoogleCodeExporter commented 9 years ago 
did you ever manage to get this to work? I have the same router and bell turbo 
stick (Novatel U679) and I'm not too sure how exactly to configure it or set it 
as my main WAN.

Original comment by jgio...@gmail.com on 17 Jun 2015 at 6:57

GoogleCodeExporter commented 9 years ago 
I ended up buying the mofi networks router and using it instead. It's a bit 
picky about getting working, but once it get the cellular connection, it is 
able to use it properly.

Original comment by dreadwin...@gmail.com on 17 Jun 2015 at 7:31