ghost commented 10 months ago

SD-files on card not shown, upload new files gets rejected after showing progress bar.

I have formatted the sd card with fat32. I am using an ESP32-CAM board. I have run a script that reads, writes, appends data to the sd card and it reported file actions as successful. I have created a test.txt file on the SD-card.

Using the ESP3D web view the SD card is shown as empty (the file test.txt is not shown) Trying to upload a gcode file always gets rejected with error 12, sometimes immediately, somtimes after showing a partial progress bar.

ESP3D Firmware: 2.1.3b0

Wifi mode: AP
Flash method: [Arduino Ide 2.2.1]
Any change done in FW: None

Target Firmware: Marlin

Board Name: ESP32-CAM

Error on console:

11:29:15.819 -> M117 SD upload failed 11:29:17.819 -> Guru Meditation Error: Core 1 panic'ed (LoadProhibited). Exception was unhandled. 11:29:17.819 -> Core 1 register dump: 11:29:17.819 -> PC : 0x400e1744 PS : 0x00060430 A0 : 0x800e1820 A1 : 0x3ffb1ad0
11:29:17.819 -> A2 : 0x00000000 A3 : 0x3ffb1b1f A4 : 0x00000001 A5 : 0x00000001
11:29:17.819 -> A6 : 0x00000001 A7 : 0x00000000 A8 : 0x00000000 A9 : 0x00000000
11:29:17.852 -> A10 : 0x3ffd21d8 A11 : 0x00000000 A12 : 0x3ffc1b4c A13 : 0x3ffc74b8
11:29:17.852 -> A14 : 0x3ffc1b40 A15 : 0x3ffc74b8 SAR : 0x0000000a EXCCAUSE: 0x0000001c
11:29:17.852 -> EXCVADDR: 0x00000008 LBEG : 0x4008c149 LEND : 0x4008c159 LCOUNT : 0xffffffff
11:29:17.852 -> 11:29:17.852 -> ELF file SHA256: 0000000000000000 11:29:17.883 -> 11:29:17.883 -> Backtrace: 0x400e1744:0x3ffb1ad0 0x400e181d:0x3ffb1af0 0x4018cc9d:0x3ffb1b10 0x400e3c41:0x3ffb1b40 0x400e4861:0x3ffb1b60 0x400e5759:0x3ffb1d60 0x400e6e79:0x3ffb1f20 0x400d82d9:0x3ffb1f70 0x400d833a:0x3ffb1f90 0x400ede08:0x3ffb1fb0 0x4008dde6:0x3ffb1fd0 11:29:17.883 -> 11:29:17.883 -> Rebooting...

github-actions[bot] commented 10 months ago

Thank your for submiting, please be sure you followed template or your issue may be dismissed. if you deleted the template it is here

luc-github commented 10 months ago

ESP32 Cam is not supported in ESP3D 2.1 (only 3.0) also ESP3D 2.1 does not allow direct Sd access (only 3.0), so the card you try to acces is printer one using M28/M29 protocol Is that the case ?

You did not shared the configuration you set in esp3d so it is hard to know what the issue is

ghost commented 10 months ago

Hi Luc Thanks for coming back with this. Can you point me to a supported ESP board? What version of esp3d do I need to access the Sd card? I have no printer connected yet but plan to use it with anycubic kobra max. It has a USB port and I can print over serial using Simplify 3d. Regards Juerg

Am Mi., 8. Nov. 2023 um 11:53 Uhr schrieb Luc @.***>:

ESP32 Cam is not supported in ESP3D 2.1 also ESP3D 2.1 does not allow direct Sd access, so the card you try to acces is printer one using M28/M29 protocol Is that the case ?

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1801629747, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CFEXBILXYHTYK2AFLDYDNQCJAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBRGYZDSNZUG4 . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

ghost commented 10 months ago

I have found this video about ESP32CAM and esp3d by Jason Winfield. https://www.youtube.com/watch?v=CdHXRQlK3ds Unfortunately my English is not good enough to be able to follow his vocal explanations.

Am Mi., 8. Nov. 2023 um 11:53 Uhr schrieb Luc @.***>:

ESP32 Cam is not supported in ESP3D 2.1 also ESP3D 2.1 does not allow direct Sd access, so the card you try to acces is printer one using M28/M29 protocol Is that the case ?

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1801629747, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CFEXBILXYHTYK2AFLDYDNQCJAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBRGYZDSNZUG4 . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 10 months ago

On ESP32 Cam the Connected SD is used to save frame from Camera, currently there is no way to share this SD with printer, so even you upload file on it the printer won't see it. Also ESP3D does not have streaming feature for 3D printer only basic one for CNC GRBL and even this one is not optimized for laser usage. The https://github.com/luc-github/ESP3D/issues/243 give current status on ESP3D - and the SD usage is still valid here : https://github.com/luc-github/ESP3D/discussions/540#discussioncomment-2897564

NOTe: About Jason Winfield. video you can enable subtitle and enable automatic translation

ghost commented 10 months ago

Hi Luc Looks like you have a large task at hand. I have downloaded esp3d version 3.0 (alpha) but get a compile error (Arduino IDE 2.2.1) :

/home/juerg/Arduino/ESP3d/ESP3D-3.0/esp3d/src/modules/camera/camera.cpp: In member function 'bool Camera::handle_snap(WebServer, const char, const char*)': /home/juerg/Arduino/ESP3d/ESP3D-3.0/esp3d/src/modules/camera/camera.cpp:81:5: error: 'HTTP_Server' has not been declared HTTP_Server::set_http_headers(); ^~~

exit status 1

Compilation error: 'HTTP_Server' has not been declared

Any hint?

Thanks Juerg

Am Mi., 8. Nov. 2023 um 11:53 Uhr schrieb Luc @.***>:

ESP32 Cam is not supported in ESP3D 2.1 also ESP3D 2.1 does not allow direct Sd access, so the card you try to acces is printer one using M28/M29 protocol Is that the case ?

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1801629747, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CFEXBILXYHTYK2AFLDYDNQCJAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBRGYZDSNZUG4 . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 10 months ago

it have been fixed this morning https://github.com/luc-github/ESP3D/issues/963 - you need to sync your download with latest code

ghost commented 10 months ago

Downloaded your latest code just now. Compilation results now in: /home/juerg/Arduino/ESP3d/ESP3D-3.0/ESP3D-3.0/esp3d/src/modules/http/handlers/handle-description_xml.cpp: In static member function 'static void HTTP_Server::handle_SSDP()': /home/juerg/Arduino/ESP3d/ESP3D-3.0/ESP3D-3.0/esp3d/src/modules/http/handlers/handle-description_xml.cpp:39:48: error: 'class SSDPClass' has no member named 'getSchema'; did you mean 'schema'? _webserver->send(200, "text/xml", SSDP.getSchema()); ^~~~~ schema

exit status 1

Compilation error: 'class SSDPClass' has no member named 'getSchema'; did you mean 'schema'?

Am Do., 9. Nov. 2023 um 09:17 Uhr schrieb Luc @.***>:

it have been fixed this morning #963 https://github.com/luc-github/ESP3D/issues/963 - you need to sync your download with latest code

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1803349031, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CHX4FGPGQ5VXZIHRYLYDSGP7AVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBTGM2DSMBTGE . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 10 months ago

are you using the correct version of SSDP ? the one I provide in repository

ghost commented 10 months ago

I have a folder ESP3D-3.0/libraries/ESP32SSDP-1.2.0 in my project. In "ESP3D-3.0/esp3d/src/modules/network/netservices.cpp" an "#include <ESP32SSDP.h" Does it need to be in another location?

Am Fr., 10. Nov. 2023 um 09:52 Uhr schrieb Luc @.***>:

are you using the correct version of SSDP ? the one I provide in repository

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1805329647, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CEBFQB2SWDUOFYOVS3YDXTNDAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBVGMZDSNRUG4 . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 10 months ago

are you compiling using arduino or platformio ? you error seems showing you compile from Arduino ide

ghost commented 10 months ago

right, i am using Arduino IDE 2.2.1

Am Fr., 10. Nov. 2023 um 11:02 Uhr schrieb Luc @.***>:

are you compiling using arduino or platformio ? you error seems showing you compile from Arduino ide

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1805433049, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CAHGAL2BTDEGCUWRGDYDX3R3AVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBVGQZTGMBUHE . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 10 months ago

then as mentioned in doc https://esp3d.io/esp3d/v3.x/installation/arduino/index.html

ghost commented 10 months ago

Hi Luc I followed your instructions and it's compiling now :-). Will soon try if it works for me. I hope I didn't distract you too much.

Am Fr., 10. Nov. 2023 um 11:05 Uhr schrieb Luc @.***>:

then as mentioned in doc https://esp3d.io/esp3d/v3.x/installation/arduino/index.html [image: image] https://user-images.githubusercontent.com/8822552/282026294-5e96d188-e3f3-4796-b0ee-c20c42f3124b.png

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1805437663, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CAH55SUKU6TICU7LJLYDX355AVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBVGQZTONRWGM . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

ghost commented 10 months ago

Hi Luc I think I give up. Program compiles but reboots endlessly

14:15:57.596 ->

14:15:57.596 -> rst:0x3 (SW_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)

14:15:57.628 -> configsip: 0, SPIWP:0xee

14:15:57.628 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00

14:15:57.628 -> mode:DIO, clock div:1

14:15:57.628 -> load:0x3fff0030,len:1344

14:15:57.628 -> load:0x40078000,len:13964

14:15:57.628 -> load:0x40080400,len:3600

14:15:57.628 -> entry 0x400805f0

14:15:58.049 -> ets Jul 29 2019 12:21:46

Am Fr., 10. Nov. 2023 um 11:31 Uhr schrieb juerg maier < @.***>:

Hi Luc I followed your instructions and it's compiling now :-). Will soon try if it works for me. I hope I didn't distract you too much.

Am Fr., 10. Nov. 2023 um 11:05 Uhr schrieb Luc @.***>:

then as mentioned in doc https://esp3d.io/esp3d/v3.x/installation/arduino/index.html [image: image] https://user-images.githubusercontent.com/8822552/282026294-5e96d188-e3f3-4796-b0ee-c20c42f3124b.png

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1805437663, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CAH55SUKU6TICU7LJLYDX355AVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBVGQZTONRWGM . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 10 months ago

let me guess you: enabled pin reset on esp32cam? or you enabled sd as spi card reader

ghost commented 10 months ago

what would show more information during the setup?

my configuration.h: /**** *

SD card pins
****/

/* SD card detect pin

The pin used to detect SD card */ // #define ESP_SD_DETECT_PIN 4

/* SD card detect pin value

State of SD card detect pin when card is present */ // #define ESP_SD_DETECT_VALUE 0

/* SD shared flag pin

The pin used to enable SD card for ESP board */ // #define ESP_FLAG_SHARED_SD_PIN -1

/* SD shared flag pin value

State of SD card shared pin for ESP board */ // #define ESP_FLAG_SHARED_SD_VALUE 0

/* SD card CS pin

The pin used to select SD card in SPI mode */ // #define ESP_SD_CS_PIN 5

/* Enable pin reset feature

Use a pin to reset ESP3D settings */ // #define PIN_RESET_FEATURE

Am Fr., 10. Nov. 2023 um 14:48 Uhr schrieb Luc @.***>:

let me guess you: enabled pin reset on esp32cam? or you enabled sd as spi card reader

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1805762862, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CAOQ5F5P2FI6ZHWERDYDYWBNAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBVG43DEOBWGI . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 10 months ago

I doubt this is the configuration.h most of configuration are missing

ghost commented 10 months ago

it was just the part of configuration.h I thought would be related to your assumptions.

Does it matter what partition schema I use? I currently have selected "Huge App (3 MB no OTA, 1 MB SPIFFS)"

I have tried to modify configuration.h to show more information:

define ESP_LOG_FEATURE LOG_OUTPUT_SERIAL0

define ESP3D_DEBUG_LEVEL LOG_LEVEL_VERBOSE

this is what I get in the serial monitor (repeated after 10s) 475:4

16:12:30.261 -> [ESP3D][boot_delay.cpp:54] begin(): Boot delay done

16:12:30.261 -> [ESP3D][settings_esp3d.cpp:337] read_byte(): read_byte 855

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1088] getDefaultByteSetting(): getDefaultByteSetting 855

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 855:

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 0:

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 1:

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 1:

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1092] getDefaultByteSetting(): getDefaultByteSetting found

16:12:30.325 -> [ESP3D][settings_esp3d.cpp:1094] getDefaultByteSetting(): getDefaultByteSetting is 1

16:12:30.325 -> [ESP3D][settings_esp3d.cpp:339] read_byte(): default value 1

16:12:30.325 -> [ESP3D][esp_sd.cpp:160] accessFS(): Accessing Direct SD

16:12:30.325 -> [ESP3D][esp_sd.cpp:164] accessFS(): Checking SD state

16:12:30.325 -> [ESP3D][sdio_esp32.cpp:62] getState(): last init was failed try sd_mmc begin

16:12:30.389 -> E (10855) vfs_fat_sdmmc: mount_to_vfs failed (0xffffffff).

16:12:30.389 -> [ESP3D-ERROR][sdio_esp32.cpp:74] getState(): sd_mmc begin failed

16:12:30.389 -> [ESP3D-ERROR][esp_sd.cpp:166] accessFS(): SD not present

16:12:30.389 -> [ESP3D][esp_sd.cpp:181] releaseFS(): Release SD

16:12:30.389 -> [ESP3D][esp3d.cpp:96] begin(): Mode 0

16:12:30.421 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 168:

16:12:30.421 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.421 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 7:

16:12:30.421 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val ESP3D:

16:12:30.421 -> [ESP3D-ERROR][settings_esp3d.cpp:695] GetSettingsVersion(): Invalid Settings Version

16:12:30.454 -> [ESP3D][esp3d.cpp:98] begin(): Need reset settings

16:12:30.454 -> [ESP3D][serial_service.cpp:408] reset(): Reset serial

16:12:30.454 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 112:

16:12:30.454 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 1:

16:12:30.454 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 4:

16:12:30.454 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 115200:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 0:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 0:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 1:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 5:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 1:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 32:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val NETWORK_SSID:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 1:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 32:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val NETWORK_SSID:

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 2

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 2

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 3

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 2

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 3

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 3

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 4

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 4

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 5

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 5

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 6

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 6

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 7

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 7

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 8

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 8

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 9

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 9

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 10

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 10

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 11

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 11

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 12

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 12

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 13

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 13

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 14

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 14

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 15

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 15

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 16

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 16

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 17

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 17

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 18

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 18

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 19

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 19

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 20

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 20

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 21

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 21

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 22

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 22

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 23

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 23

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 24

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 24

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 25

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 25

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 26

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 26

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 27

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 27

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 28

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 28

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 29

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 29

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 30

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 30

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 31

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 31

6:12:30.933 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 32

16:12:30.933 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 32

16:12:30.933 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 33

16:12:30.933 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 33

16:12:30.933 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 34:

16:12:30.933 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 64:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 12345678:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 34:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 64:

16:12:30.997 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 12345678:

16:12:30.997 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 35

16:12:30.997 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 35

16:12:30.997 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 36

16:12:30.997 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 36

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 37

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 37

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 38

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 38

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 39

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 39

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 40

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 40

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 41

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 41

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 42

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 42

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 43

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 43

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 44

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 44

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 45

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 45

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 46

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 46

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 47

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 47

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 48

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 48

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 49

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 49

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 50

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 50

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 51

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 51

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 52

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 52

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 53

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 53

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 54

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 54

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 55

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 55

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 56

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 56

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 57

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 57

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 58

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 58

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 59

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 59

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 60

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 60

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 61

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 61

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 62

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 62

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 63

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 63

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 64

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 64

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 65

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 65

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 66

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 66

16:12:31.413 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 67

16:12:31.413 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 67

16:12:31.413 -> [ESP3D][esp3d.cpp:238] restart_now(): Restarting

16:12:31.413 -> [ESP3D][serial_service.cpp:126] begin(): Serial 0 begin for 1

16:12:31.413 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 112:

16:12:31.413 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 1:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 4:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 115200:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 112:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 1:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 4:

16:12:31.477 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 115200:

16:12:31.477 -> [ESP3D][serial_service.cpp:159] begin(): Baud rate is 115200 , default is 115200

16:12:31.477 -> [ESP3D][serial_service.cpp:199] begin(): Serial 0 for 1 is started

16:12:31.477 -> ets Jul 29 2019 12:21:46

16:12:31.477 ->

16:12:31.477 -> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)

16:12:31.477 -> configsip: 0, SPIWP:0xee

16:12:31.509 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00

16:12:31.509 -> mode:DIO, clock div:1

I have attached my complete configuration.h

Am Fr., 10. Nov. 2023 um 15:49 Uhr schrieb Luc @.***>:

I doubt this is the configuration.h most of configuration are missing

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1805878680, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CGZ6JGPDZA5OBH6XZ3YDY5HTAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBVHA3TQNRYGA . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

ghost commented 10 months ago

I have formatted the SD card with Fat32. now it gets detected but the app is looking for an "ini" File?

16:53:02.032 -> [ESP3D][settings_esp3d.cpp:1092] getDefaultByteSetting(): getDefaultByteSetting found

16:53:02.064 -> [ESP3D][settings_esp3d.cpp:1094] getDefaultByteSetting(): getDefaultByteSetting is 1

16:53:02.064 -> [ESP3D][settings_esp3d.cpp:339] read_byte(): default value 1

16:53:02.064 -> [ESP3D][esp_sd.cpp:160] accessFS(): Accessing Direct SD

16:53:02.064 -> [ESP3D][esp_sd.cpp:164] accessFS(): Checking SD state

16:53:02.064 -> [ESP3D][sdio_esp32.cpp:62] getState(): last init was failed try sd_mmc begin

16:53:02.226 -> [ESP3D][sdio_esp32.cpp:65] getState(): sd_mmc begin succeed

16:53:02.226 -> [ESP3D][sdio_esp32.cpp:69] getState(): sd_mmc card type succeed

16:53:02.226 -> [ESP3D][esp_sd.cpp:171] accessFS(): SD present

16:53:02.258 -> [ESP3D][esp_sd.cpp:173] accessFS(): Accessing SD is ok

16:53:02.258 -> [ESP3D][update_service.cpp:481] begin(): Update SD for update requestest

16:53:02.258 -> [ESP3D-ERROR][esp_config_file.cpp:45] processFile(): No ini file

16:53:02.258 -> [ESP3D-ERROR][update_service.cpp:494] begin(): Processing ini file failed

16:53:02.258 -> [ESP3D][esp_sd.cpp:181] releaseFS(): Release SD

Am Fr., 10. Nov. 2023 um 16:24 Uhr schrieb juerg maier < @.***>:

it was just the part of configuration.h I thought would be related to your assumptions.

Does it matter what partition schema I use? I currently have selected "Huge App (3 MB no OTA, 1 MB SPIFFS)"

I have tried to modify configuration.h to show more information:

define ESP_LOG_FEATURE LOG_OUTPUT_SERIAL0

define ESP3D_DEBUG_LEVEL LOG_LEVEL_VERBOSE

this is what I get in the serial monitor (repeated after 10s) 475:4

16:12:30.261 -> [ESP3D][boot_delay.cpp:54] begin(): Boot delay done

16:12:30.261 -> [ESP3D][settings_esp3d.cpp:337] read_byte(): read_byte 855

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1088] getDefaultByteSetting(): getDefaultByteSetting 855

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 855:

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 0:

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 1:

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 1:

16:12:30.302 -> [ESP3D][settings_esp3d.cpp:1092] getDefaultByteSetting(): getDefaultByteSetting found

16:12:30.325 -> [ESP3D][settings_esp3d.cpp:1094] getDefaultByteSetting(): getDefaultByteSetting is 1

16:12:30.325 -> [ESP3D][settings_esp3d.cpp:339] read_byte(): default value 1

16:12:30.325 -> [ESP3D][esp_sd.cpp:160] accessFS(): Accessing Direct SD

16:12:30.325 -> [ESP3D][esp_sd.cpp:164] accessFS(): Checking SD state

16:12:30.325 -> [ESP3D][sdio_esp32.cpp:62] getState(): last init was failed try sd_mmc begin

16:12:30.389 -> E (10855) vfs_fat_sdmmc: mount_to_vfs failed (0xffffffff).

16:12:30.389 -> [ESP3D-ERROR][sdio_esp32.cpp:74] getState(): sd_mmc begin failed

16:12:30.389 -> [ESP3D-ERROR][esp_sd.cpp:166] accessFS(): SD not present

16:12:30.389 -> [ESP3D][esp_sd.cpp:181] releaseFS(): Release SD

16:12:30.389 -> [ESP3D][esp3d.cpp:96] begin(): Mode 0

16:12:30.421 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 168:

16:12:30.421 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.421 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 7:

16:12:30.421 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val ESP3D:

16:12:30.421 -> [ESP3D-ERROR][settings_esp3d.cpp:695] GetSettingsVersion(): Invalid Settings Version

16:12:30.454 -> [ESP3D][esp3d.cpp:98] begin(): Need reset settings

16:12:30.454 -> [ESP3D][serial_service.cpp:408] reset(): Reset serial

16:12:30.454 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 112:

16:12:30.454 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 1:

16:12:30.454 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 4:

16:12:30.454 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 115200:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 0:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 0:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 1:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 5:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 1:

16:12:30.485 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 32:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val NETWORK_SSID:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 1:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 32:

16:12:30.517 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val NETWORK_SSID:

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 2

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 2

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 3

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 2

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 3

16:12:30.549 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 3

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 4

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 4

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 5

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 5

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 6

16:12:30.581 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 6

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 7

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 7

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 8

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 8

16:12:30.613 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 9

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 9

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 10

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 10

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 11

16:12:30.645 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 11

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 12

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 12

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 13

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 13

16:12:30.677 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 14

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 14

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 15

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 15

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 16

16:12:30.709 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 16

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 17

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 17

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 18

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 18

16:12:30.741 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 19

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 19

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 20

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 20

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 21

16:12:30.774 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 21

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 22

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 22

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 23

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 23

16:12:30.805 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 24

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 24

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 25

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 25

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 26

16:12:30.837 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 26

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 27

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 27

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 28

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 28

16:12:30.869 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 29

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 29

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 30

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 30

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 31

16:12:30.901 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 31

6:12:30.933 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 32

16:12:30.933 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 32

16:12:30.933 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 33

16:12:30.933 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 33

16:12:30.933 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 34:

16:12:30.933 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 64:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 12345678:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 34:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 2:

16:12:30.966 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 64:

16:12:30.997 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 12345678:

16:12:30.997 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 35

16:12:30.997 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 35

16:12:30.997 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 36

16:12:30.997 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 36

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 37

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 37

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 38

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 38

16:12:31.029 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 39

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 39

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 40

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 40

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 41

16:12:31.061 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 41

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 42

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 42

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 43

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 43

16:12:31.094 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 44

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 44

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 45

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 45

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 46

16:12:31.125 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 46

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 47

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 47

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 48

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 48

16:12:31.157 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 49

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 49

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 50

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 50

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 51

16:12:31.189 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 51

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 52

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 52

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 53

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 53

16:12:31.221 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 54

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 54

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 55

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 55

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 56

16:12:31.254 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 56

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 57

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 57

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 58

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 58

16:12:31.285 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 59

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 59

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 60

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 60

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 61

16:12:31.317 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 61

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 62

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 62

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 63

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 63

16:12:31.350 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 64

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 64

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 65

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 65

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 66

16:12:31.381 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 66

16:12:31.413 -> [ESP3D-ERROR][settings_esp3d.cpp:1514] getSettingPtr(): Invalid setting 67

16:12:31.413 -> [ESP3D-ERROR][settings_esp3d.cpp:680] reset(): Error unknow entry 67

16:12:31.413 -> [ESP3D][esp3d.cpp:238] restart_now(): Restarting

16:12:31.413 -> [ESP3D][serial_service.cpp:126] begin(): Serial 0 begin for 1

16:12:31.413 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 112:

16:12:31.413 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 1:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 4:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 115200:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1518] getSettingPtr(): Got index 112:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1519] getSettingPtr(): type 1:

16:12:31.446 -> [ESP3D][settings_esp3d.cpp:1520] getSettingPtr(): size 4:

16:12:31.477 -> [ESP3D][settings_esp3d.cpp:1521] getSettingPtr(): default_val 115200:

16:12:31.477 -> [ESP3D][serial_service.cpp:159] begin(): Baud rate is 115200 , default is 115200

16:12:31.477 -> [ESP3D][serial_service.cpp:199] begin(): Serial 0 for 1 is started

16:12:31.477 -> ets Jul 29 2019 12:21:46

16:12:31.477 ->

16:12:31.477 -> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)

16:12:31.477 -> configsip: 0, SPIWP:0xee

16:12:31.509 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00

16:12:31.509 -> mode:DIO, clock div:1

I have attached my complete configuration.h

Am Fr., 10. Nov. 2023 um 15:49 Uhr schrieb Luc @.***>:

I doubt this is the configuration.h most of configuration are missing

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1805878680, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CGZ6JGPDZA5OBH6XZ3YDY5HTAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBVHA3TQNRYGA . You are receiving this because you authored the thread.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 10 months ago

yes if you enabled SD updater, but it is optionnal, only useful if you want to change a setting using this method https://esp3d.io/esp3d/v3.x/documentation/update/index.html

luc-github commented 9 months ago

@juergmaier I found a glitch in code that was introduced with recent PR that mess up the reset and in some occasion and lead to dead loop reset at start You may want to try latest git to confirm that was your issue

ghost commented 9 months ago

Hi Luc Thanks for your notification. I have loaded it and it looks much better, no resets any more I do not understand the esp_core_dump error or how to correct this setting. I also have the problem that IP address 192.168.0.1 is my routers ip. I have tried to assign the ESP32 a different IP with the esp3dcnf.ini on the vfat formatted SD card but it looks like the card is not accessed any more (before it renamed the .ini file to .ok, also no SD related logs appear on the serial monitor). Maybe you have some more advice how to make it run?

6:45:25.123 -> ets Jul 29 2019 12:21:46

16:45:25.123 ->

16:45:25.123 -> rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)

16:45:25.123 -> configsip: 0, SPIWP:0xee

16:45:25.123 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00

16:45:25.123 -> mode:DIO, clock div:1

16:45:25.123 -> load:0x3fff0030,len:1344

16:45:25.123 -> load:0x40078000,len:13964

16:45:25.123 -> load:0x40080400,len:3600

16:45:25.123 -> entry 0x400805f0

16:45:25.542 -> E (418) esp_core_dump_f�� ͡: Incorrect size of core dump image: 196611

16:45:36.094 -> M117 Setup wifi

16:45:36.803 -> M117 AP SSID: 'ESP3D' is started and protected by password (setup mode)

16:45:38.811 -> M117 192.168.0.1

16:45:39.911 -> M117 192.168.0.1

Am Mo., 13. Nov. 2023 um 12:54 Uhr schrieb Luc @.***>:

@juergmaier https://github.com/juergmaier I found a glitch in code that was introduced with recent PR that mess up the reset and in some occasion and lead to dead loop reset at start You may want to try latest git to confirm that was your issue

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1808018057, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CAK53WFNX3FN26CLCDYEIC7ZAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBYGAYTQMBVG4 . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

the partition for ESP3Cam with ESP3D should be min_spiffs.csv https://github.com/espressif/arduino-esp32/blob/master/tools/partitions/min_spiffs.csv, I never had such message About SD I do not know how you configured it in configuration.h so I have no clue You can configure ESP3D using web interface or serial terminal by ESPdirect commands

I encourage you to read the doc : https://esp3d.io/esp3d/v3.x/documentation/commands/index.html

Define IP value / Mask / Gateway/ DNS , then move to Static IP instead of Default DHCP, but be sure your setting match your network

ghost commented 9 months ago

sorry Luc, it looks to be over my head. I was able to change the IP with [ESP107]192.168.0.200, shows with [ESP111] After reboot this ip is shown in the log but I can't ping the address. Maybe there are just too many options how to set up the ESP32. To get the ESP3d shown in the browser I expected to set it into AP-Mode and then access it in my browser with http://192.168.0.200 The SD card thing is also a problem to me. What should I do with the content of the link you sent me (min_spiffs.csv)? Is there a tutorial how to set up the SD-Card?

Am Mo., 13. Nov. 2023 um 17:04 Uhr schrieb Luc @.***>:

the partition for ESP3Cam with ESP3D should be min_spiffs.csv https://github.com/espressif/arduino-esp32/blob/master/tools/partitions/min_spiffs.csv, I never had such message About SD I do not know how you configured it in configuration.h so I have no clue You can configure ESP3D using web interface or serial terminal by ESPdirect commands

I encourage you to read the doc : https://esp3d.io/esp3d/v3.x/documentation/commands/index.html

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1808459151, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CAPA5ODNFWFIRIZFX3YEJAIFAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBYGQ2TSMJVGE . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

ghost commented 9 months ago

Some progress now. I was able to connect my WiFi to the SSID ESP3D. I was also able to upload a file to the SD-Card (it still is vfat) All the links however (Firmware/Interface/Help) result in 'unable to connect'

Am Mo., 13. Nov. 2023 um 17:04 Uhr schrieb Luc @.***>:

the partition for ESP3Cam with ESP3D should be min_spiffs.csv https://github.com/espressif/arduino-esp32/blob/master/tools/partitions/min_spiffs.csv, I never had such message About SD I do not know how you configured it in configuration.h so I have no clue You can configure ESP3D using web interface or serial terminal by ESPdirect commands

I encourage you to read the doc : https://esp3d.io/esp3d/v3.x/documentation/commands/index.html

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1808459151, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CAPA5ODNFWFIRIZFX3YEJAIFAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBYGQ2TSMJVGE . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

are you in Access Point or Client Mode ?

ghost commented 9 months ago

how would I know?

Am Di., 14. Nov. 2023 um 01:21 Uhr schrieb Luc @.***>:

are you in Access Point or Client Mode ?

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1809341946, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CGHJESOZAJUS3PU43TYEK2PTAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBZGM2DCOJUGY . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

you do not know your own setup ?..... So why willing to change the ip address ? Access point mode : you connect to esp board wifi with your PC to esp network

Client mode : the esp joint your local wifi and can access it thrue your local network

ghost commented 9 months ago

Sorry, not very fluent in networking. Based on your clarification: I am in Access Point mode and connect the Wifi on my PC to the ESP3D network.

When I point my browser window to this address I get this page shown

[image: image.png]

I assume the File I see is on Flash and not on the SD card. And as the links of Firmware, Interface and Help point to internet addresses they do not work with my connection to the ESP3D?

09:09:40.834 -> E (439) esp_core_dump_f�� ͡: Incorrect size of core dump image: 196611

09:09:51.404 -> M117 Setup wifi

09:09:52.145 -> M117 AP SSID: 'ESP3D' is started and protected by password (setup mode)

09:09:54.175 -> M117 192.168.0.200

09:09:55.237 -> M117 192.168.0.200

09:09:59.106 -> M117 New client

Am Di., 14. Nov. 2023 um 09:02 Uhr schrieb Luc @.***>:

you do not know your own setup ?..... So why willing to change the ip address ? Access point mode : you connect to esp board wifi with your PC to esp network

Client mode : the esp joint your local wifi and can access it thrue your local network

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1809708709, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CC75HLKCLSYOGUNQDTYEMQRRAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBZG4YDQNZQHE . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

well in access mode you are on limited network of esp so there no magic solution for you esp to access internet The access point is made for configuration purpose not daily usage

you must make.the.esp to join your local network, so after you can access to internet

ghost commented 9 months ago

another question: I have tried to set the ESP into STA mode but can't find a command to switch from AP to STA mode? I have set the SSID with [ESP100] and mode to STATIC with [ESP102] [ESP110] shows WIFI-SETUP

Am Di., 14. Nov. 2023 um 09:38 Uhr schrieb Luc @.***>:

well in access mode you are on limited network of esp so there no magic solution for you esp to access internet The access point is made for configuration purpose not daily usage

you must make.the.esp to join your local network after you can access to internet

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1809755239, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CBCX74CHIPQWTPKKQDYEMUXBAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBZG42TKMRTHE . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

why change ip to static ? as you seems.not handling network per your feedback it is sireit won'tbe properly configured. [ESP110]WIFI-STA is the command to switch to Station mode

ghost commented 9 months ago

applied [ESP110]WIFI-STA and [ESP102]DHCP In the startuplog I assume Connecting fails and it falls back to AP mode?

1:59:59.272 -> M117 Setup wifi

11:59:59.400 -> M117 Connecting

12:00:20.081 -> M117 AP SSID: '192.168.0.201' is started and protected by password (setup mode)

12:00:22.054 -> M117 192.168.0.201

12:00:23.156 -> M117 192.168.0.201

12:03:06.559 -> ;WIFI-SETUP

Am Di., 14. Nov. 2023 um 11:49 Uhr schrieb Luc @.***>:

why change ip to static ? as you seems.not handling network per your feedback it is sireit won'tbe properly configured. [ESP110]WIFI-STA is the command to switch to Station mode

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1809971228, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CC745EAQN7GRTH7X7LYENEETAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMBZHE3TCMRSHA . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

[ESP100] with your acces point SSID [ESP101] with your acces point password if any of them is wrong so ESP3D cannot join wifi it fall back to ESP3D access point mode to let you fix your issue

ghost commented 9 months ago

new situation I switched to use jason's configuration https://jasonwinfield.nz/esp3d-config-file/ I compiled and loaded again. I used ESP100 and ESP101 to set my SSID and pwd esp3d started and it found a free IP. I can ping that IP and my router shows it as connected device. Entering this IP in my browser however tells me that it is unable to connect?

Am Di., 14. Nov. 2023 um 13:07 Uhr schrieb Luc @.***>:

[ESP100] with your acces point SSID [ESP101] with your acces point password if any of them is wrong so ESP3D cannot join wifi it fall back to ESP3D access point mode to let you fix your issue

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1810082979, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CBIZ7DYSTZSG5JDOHTYENNGZAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMJQGA4DEOJXHE . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

what is your opereating system ?

ghost commented 9 months ago

ubuntu 23.10

Am Di., 14. Nov. 2023 um 14:49 Uhr schrieb Luc @.***>:

what is your opereating system ?

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1810238085, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CA3AIZ7XWXZRA75FL3YENZFVAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMJQGIZTQMBYGU . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

esp3d is discoverable if you do not know the ip using one of these tools : https://esp3d.io/tools/discovery/

ghost commented 9 months ago

could not make these tools to install/run I have tried the browser Falkon and it says "192.168.0.115 refused to connect" Do I need another setting in the ESP3d to make the site accessible?

Am Di., 14. Nov. 2023 um 15:11 Uhr schrieb Luc @.***>:

esp3d is discoverable if you do not know the ip using one of these tools : https://esp3d.io/tools/discovery/

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1810285278, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CBQ4WOPG6NVAM6SQGDYEN3YBAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMJQGI4DKMRXHA . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

check what [ESP420] give as output

ghost commented 9 months ago

08:42:25.527 -> ;echo:chip id: 20694

08:42:25.527 -> ;echo:CPU Freq: 240Mhz

08:42:25.527 -> ;echo:CPU Temp: 61.1C

08:42:25.527 -> ;echo:free mem: 106.95 KB - PSRAM:3.88 MB

08:42:25.527 -> ;echo:SDK: v4.4.5

08:42:25.527 -> ;echo:flash size: 4.00 MB

08:42:25.527 -> ;echo:size for update: 0 B

08:42:25.527 -> ;echo:FS type: LittleFS

08:42:25.560 -> ;echo:FS usage: 248.00 KB/896.00 KB

08:42:25.560 -> ;echo:baud: 115200

08:42:25.560 -> ;echo:sleep mode: none

08:42:25.560 -> ;echo:wifi: ON

08:42:25.560 -> ;echo:hostname: myesp

08:42:25.560 -> ;echo:HTTP port: 23

08:42:25.560 -> ;echo:Telnet port: 30000

I have set the http port with [ESP121] to 80 but still no connection

Am Mi., 15. Nov. 2023 um 01:06 Uhr schrieb Luc @.***>:

check what [ESP420] give as output

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1811588965, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CC3CONG4P74ICKZWGTYEQBRZAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMJRGU4DQOJWGU . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

SDK: v4.4.5 this is not correct you must have SDK 4.4.4 What esp32 arduino core are you using ? you are supposed to use 2.0.8 : https://esp3d.io/esp3d/v3.x/installation/arduino/index.html

luc-github commented 9 months ago

also HTTP port: 23 is wrong it should be 80 that is why you cannot connect

ghost commented 9 months ago

after setting the http port to 80 a reboot of the ESP shows now the same webpage as I had in AP-mode. The top section links point to: Firmware: https://github.com/luc-github/ESP3D/tree/3.0 Interface: https://github.com/luc-github/ESP3D-WEBUI/tree/3.0 Help: https://github.com/luc-github/ESP3D/wiki

these sites are shown but I assume there is still something wrong with my setup?

Am Mi., 15. Nov. 2023 um 01:06 Uhr schrieb Luc @.***>:

check what [ESP420] give as output

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1811588965, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CC3CONG4P74ICKZWGTYEQBRZAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMJRGU4DQOJWGU . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

you use wrong core - a one I never tested so can be anything else wrong anywhere

ghost commented 9 months ago

my arduino board manager only allows to select: 1.0.0 .. 1.0.6 2.0.10 and 2.0.11

and I do not know how to change SDK to version 4.4.4?

Am Mi., 15. Nov. 2023 um 08:58 Uhr schrieb Luc @.***>:

SDK: v4.4.5 this is not correct you must have SDK 4.4.4 What esp32 arduino core are you using ? you are supposed to use 2.0.8 : https://esp3d.io/esp3d/v3.x/installation/arduino/index.html

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1811969921, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CC42SPDJZORDPFTHUTYERY3VAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMJRHE3DSOJSGE . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

https://docs.espressif.com/projects/arduino-esp32/en/latest/installing.html

ghost commented 9 months ago

tried to execute the commands but get:

Saving to: ‘get-pip.py’

get-pip.py 100%[========================================>] 2.51M --.-KB/s in 0.1s

2023-11-15 09:42:44 (20.0 MB/s) - ‘get-pip.py’ saved [2632263/2632263]

error: externally-managed-environment

× This environment is externally managed ╰─> To install Python packages system-wide, try apt install python3-xyz, where xyz is the package you are trying to install.

If you wish to install a non-Debian-packaged Python package,
create a virtual environment using python3 -m venv path/to/venv.
Then use path/to/venv/bin/python and path/to/venv/bin/pip. Make
sure you have python3-full installed.

If you wish to install a non-Debian packaged Python application,
it may be easiest to use pipx install xyz, which will manage a
virtual environment for you. Make sure you have pipx installed.

See /usr/share/doc/python3.11/README.venv for more information.

note: If you believe this is a mistake, please contact your Python installation or OS distribution provider. You can override this, at the risk of breaking your Python installation or OS, by passing --break-system-packages. hint: See PEP 668 for the detailed specification. @.***:~$

Am Mi., 15. Nov. 2023 um 09:18 Uhr schrieb Luc @.***>:

https://docs.espressif.com/projects/arduino-esp32/en/latest/installing.html

— Reply to this email directly, view it on GitHub https://github.com/luc-github/ESP3D/issues/962#issuecomment-1811993659, or unsubscribe https://github.com/notifications/unsubscribe-auth/AA6T6CBZGC46CMTHWJE2CLDYER3FDAVCNFSM6AAAAAA7CVFCX2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQMJRHE4TGNRVHE . You are receiving this because you were mentioned.Message ID: @.***>

-- Jürg Maier Trungerstrasse 33 9543 St. Margarethen Schweiz @.***

luc-github commented 9 months ago

your issue looks related to your platfom and installation setup

Did you solved it ?

luc-github / ESP3D

file upload always rejected #962

define ESP_LOG_FEATURE LOG_OUTPUT_SERIAL0

define ESP3D_DEBUG_LEVEL LOG_LEVEL_VERBOSE

define ESP_LOG_FEATURE LOG_OUTPUT_SERIAL0

define ESP3D_DEBUG_LEVEL LOG_LEVEL_VERBOSE