search

makerbase-mks / MKS-Robin

MKS Robin is a powerful 32-bit 3D printer control board with STM32F103ZET6 . Support Marlin2.0. Support MKS Robin TFT24/28/32... Screens. The motherboard integrates 5 AXIS interface, hot bed, 2 heating heads, 3 NTC100K, 2 MAX31855.Support MKS Robin WIFI for cloud printing.Supports firmware update by SD card…
https://es.aliexpress.com/item/32757129463.html?spm=a219c.12010612.8148356.9.5fc165f4oDUfFM
131 stars 129 forks source link

RepRap MKS V2 Can't connect to cura #172

Open ChrisYOLO opened 4 years ago

ChrisYOLO commented 4 years ago

So I got my new custom printer today and I plugged it into my computer. I downloaded CH340 drivers and it was detected inside the device manager (but not detected din printers and scanners). But in cura I was not able to connect it in any way. I tried using German ReRap profile still no connection via USB. My friend suggested using it as a Pursha i3 still no connection. The monitor tab was blank white .

3Dangel commented 4 years ago

I don’t think 3D printers ever gets detected in windows’ printer/scanner. It is not a “printer”.

Contact your seller of the custom printer and ask how did they connect to the PC.

Wrong Baud rate Will not allows you to connect to the PC.

Blank screen you need to ask your seller what firmware they installed in your unit. Or check for connection cables if they are well connected. Or you might need to reverse the connectors. Check YT for reprap full graphic Issue. Good luck

On Thu, May 7, 2020 at 16:27 ChrisYOLO notifications@github.com wrote:

So I got my new custom printer today and I plugged it into my computer. I downloaded CH340 drivers and it was detected inside the device manager (but not detected din printers and scanners). But in cura I was not able to connect it in any way. I tried using German ReRap profile still no connection via USB. My friend suggested using it as a Pursha i3 still no connection. The monitor tab was blank white .

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/makerbase-mks/MKS-Robin/issues/172, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFYWWXPU6B2QMQVECADZZUTRQMYWHANCNFSM4M3WVQIQ .

ChrisYOLO commented 4 years ago

I don’t think 3D printers ever gets detected in windows’ printer/scanner. It is not a “printer”. Contact your seller of the custom printer and ask how did they connect to the PC. Wrong Baud rate Will not allows you to connect to the PC. Blank screen you need to ask your seller what firmware they installed in your unit. Or check for connection cables if they are well connected. Or you might need to reverse the connectors. Check YT for reprap full graphic Issue. Good luck … On Thu, May 7, 2020 at 16:27 ChrisYOLO @.***> wrote: So I got my new custom printer today and I plugged it into my computer. I downloaded CH340 drivers and it was detected inside the device manager (but not detected din printers and scanners). But in cura I was not able to connect it in any way. I tried using German ReRap profile still no connection via USB. My friend suggested using it as a Pursha i3 still no connection. The monitor tab was blank white . — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub <#172>, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFYWWXPU6B2QMQVECADZZUTRQMYWHANCNFSM4M3WVQIQ .

I use an MKS Robin v2 and it gets detected as a USB serial ch340. On other slicers I was able to connect can you help me with the baud rate and com ports on cura I have no ideas how to fix this I am a starter

ChrisYOLO commented 4 years ago

also i get blank whitet screen on cura my printer is fine no problem but i can't get it to connect with cura

3Dangel commented 4 years ago

Try using 500000 ; 256000; 112500.... Beyond that, you really need to talk to your seller. As blank screen, you might need to reflash the right FW.

Watch YT and get some knowdlege about what you have and where you want to go from there.

On Fri, May 8, 2020 at 02:31 ChrisYOLO notifications@github.com wrote:

also i get blank whitet screen on cura my printer is fine no problem but i can't get it to connect with cura

— You are receiving this because you commented.

Reply to this email directly, view it on GitHub https://github.com/makerbase-mks/MKS-Robin/issues/172#issuecomment-625705490, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFYWWXIG2MNWBG4GVV62SGLRQO7ONANCNFSM4M3WVQIQ .