mks robin V2.4 mainboard update problem

[emreyz]

After ı try to config and update, my robin V2.4 board, screen turn to white. and ı could not do anything. could any body help me solved this issue.

what is the suitable firmware with robin 2.4 board

[emreyz]

I try 2.03 and 2.06 versions 2.06 version do on the screen "complete" but ı never do anything , after that ı ty 2.03 and turn white screen again same ı could not make anything

[GrafZahl81]

My MKS Robin 2.4 with TFT V2.0 does not update the mks_pics folder. It always gets stuck with bmp_Add.bin. It does not start after that.

[makerbase-mks]

@GrafZahl81 you can try to replace the sd and update again. @emreyz If you receive a broken motherboard, you can contact our customer service to handle it.

[pk3pdk]

@emreyz I had the same problem with the white screen after first start up, after using the MKS_Robin_V2.0.7 Release FIle screen works after SD Card update. I´m using Robin V2.4 and TFT V2.0 from August 2018... I did not connected anything except 12V Power and TFT. But I hope it works.

[emreyz]

we can use just V2.0.7 to suitable v2.4 best regards

---

Gönderen: pk3pdk notifications@github.com Gönderildi: 18 Ocak 2019 Cuma 20:32 Kime: makerbase-mks/MKS-Robin Bilgi: emreyz; Mention Konu: Re: [makerbase-mks/MKS-Robin] mks robin V2.4 mainboard update problem (#70)

@emreyzhttps://github.com/emreyz I had the same problem with the white screen after first start up, after using the MKS_Robin_V2.0.7 Release FIle screen works after SD Card update. I´m using Robin V2.4 and TFT V2.0 from August 2018... I did not connected anything except 12V Power and TFT. But I hope it works.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHubhttps://github.com/makerbase-mks/MKS-Robin/issues/70#issuecomment-455626302, or mute the threadhttps://github.com/notifications/unsubscribe-auth/AaI9ldxyoy-KHddYZmH1l68udRYdHpRhks5vEgUqgaJpZM4YeUQh.

[adarshparavoor]

I got the MKs V2.4 board i don't know how to configure this board. Any link with essential details

[makerbase-mks]

@adarshparavoor you can get the datasheet on this web https://github.com/makerbase-mks/Datasheet/tree/master/English%20datasheet If you need firmware, you can download it through this website.

https://github.com/makerbase-mks/MKS-Robin/tree/master/MKS%20Robin

[adarshparavoor]

sir,

My printer is a custom made core xy printer. board that i using MKS Robin V 2.0 End stop using here is optical sensor. The code that i used for the purpose is given below.

• X axis End stop is not working when the homing direction is as on the code given below. If i reverse this direction end stop will work. Please help me to solve this issue.

*Is it possible to add capacitive sensor then how can i add the sensor.

I need more details to finish the work. Please help me fast

On Mon, Mar 11, 2019 at 12:53 PM makerbase notifications@github.com wrote:

@adarshparavoor https://github.com/adarshparavoor you can get the datasheet on this web https://github.com/makerbase-mks/Datasheet/tree/master/English%20datasheet If you need firmware, you can download it through this website.

https://github.com/makerbase-mks/MKS-Robin/tree/master/MKS%20Robin

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/makerbase-mks/MKS-Robin/issues/70#issuecomment-471430495, or mute the thread https://github.com/notifications/unsubscribe-auth/AuKsmZAuOgb2C-V6vRvsc1M6a15RLonGks5vVgRYgaJpZM4YeUQh .

-------------------------------------------------------------

############ Based Settings( Required) #######################

machine type

0:xyz

1:corexy(x_motor = x+y, y_motor = x-y),

2:corexy(x_motor = x+y, y_motor = y-x),

3:delta

DRIVE_SYSTEM 2 #machine type

cfg_multiple_language 1 #multi-language(enable:1, disable:0)

cfg_language_type 3 #languages setting,this configuration is valid when "cfg_multiple_language" is disabled.

(simplified Chinese:1; traditional Chinese:2; English:3; Russian:4; Spanish:5;French:6;Italian:7).

NUM_EXTRUDER 1 #number of extruder (1:singal；2:dual) HAVE_HEATED_BED 1 #1:enable bed; 0:disable bed EXT0_TEMPSENSOR_TYPE 1 #1:100k thermistor；102: MAX31855 thermocouple EXT1_TEMPSENSOR_TYPE 1 #1:100k thermistor；102: MAX31855 thermocouple HEATED_BED_SENSOR_TYPE 1 #1:100k thermistor；

FEATURE_TWO_XSTEPPER 0 #change E1 singal into X , then dual X is available(enable:1; disable: 0) FEATURE_TWO_YSTEPPER 0 #change E1 singal into Y , then dual Y is available(enable:1; disable: 0) FEATURE_TWO_ZSTEPPER 0 #change E1 singal into Z , then dual Z is available(enable:1; disable: 0)

--------------------------------------------------------------

################# Machine settings ############################

EXT1_X_OFFSET 0 #E1 offset from the origin of X axis (mm) EXT1_Y_OFFSET 0 #E1 offset from the origin of Y axis (mm)

INVERT_X_DIR 0 #X motor direction, 1 goes opposite direction; INVERT_Y_DIR 0 #Y motor direction, 1 goes opposite direction;
INVERT_Z_DIR 0 #Z motor direction, 1 goes opposite direction;
EXT0_INVERSE 1 #E0motor direction, 1 goes opposite direction; EXT1_INVERSE 0 #E1motor direction, 1 goes opposite direction;

XAXIS_STEPS_PER_MM 100 #X steps per mm YAXIS_STEPS_PER_MM 100 #Y steps per mm ZAXIS_STEPS_PER_MM 400 #Z steps per mm EXT0_STEPS_PER_MM 100 #E0 steps per mm EXT1_STEPS_PER_MM 100 #E1 steps per mm

X_MAX_LENGTH 370 #the MAX X-axis distance Y_MAX_LENGTH 410 #the MAX Y-axis distance Z_MAX_LENGTH 400 #the MAX Z-axis distance X_MIN_POS 0 #the MIN X-axis distance Y_MIN_POS 0 #the MIN Y-axis distance Z_MIN_POS 0 #the MIN Z-axis distance

MIN_EXTRUDER_TEMP 175 #MIN TEMP on Extruder ,play a protective role MAX_EXTRUDER_TEMP 275 #MAX TEMP on Extruder ,play a protective role MAX_HEATED_BED_TEMP 150 #MAX TEMP on heated bed ，play a protective role

HOMING_ORDER 1 #Set direction of endstops when homing;
X_HOME_DIR 1 #Homing direction(-1:MIN，1:MAX) Y_HOME_DIR -1 #Homing direction(-1:MIN，1:MAX) Z_HOME_DIR 1 #Homing direction(-1:MIN，1:MAX)

HOMING_FEEDRATE_X 40 #the feedrate on X homing HOMING_FEEDRATE_Y 40 #the feedrate on Y homing HOMING_FEEDRATE_Z 10 #the feedrate on Z homing

1 means endstop always-on,0 is always-off----reversing the sensor logic.

ENDSTOP_X_MIN_INVERTING 0
ENDSTOP_Y_MIN_INVERTING 0
ENDSTOP_Z_MIN_INVERTING 1
ENDSTOP_X_MAX_INVERTING 0
ENDSTOP_Y_MAX_INVERTING 0
ENDSTOP_Z_MAX_INVERTING 0

1 for Min/Max endstop enable in hardware,while 0 disable

MIN_HARDWARE_ENDSTOP_X 1
MIN_HARDWARE_ENDSTOP_Y 1
MIN_HARDWARE_ENDSTOP_Z 1
MAX_HARDWARE_ENDSTOP_X 0
MAX_HARDWARE_ENDSTOP_Y 0
MAX_HARDWARE_ENDSTOP_Z 0

1 for Min/Max endstop enable in software,while 0 disable

min_software_endstop_x 0
min_software_endstop_y 0
min_software_endstop_z 0
max_software_endstop_x 1
max_software_endstop_y 1
max_software_endstop_z 1

MAX_FEEDRATE_X 200 #the Max feedrate of X moving mm/s MAX_FEEDRATE_Y 200 #the Max feedrate of Y moving mm/s MAX_FEEDRATE_Z 50 #the Max feedrate of Z moving mm/s MAX_FEEDRATE_EXT0 200 #the Max feedrate of E0 moving mm/s MAX_FEEDRATE_EXT1 200 #the Max feedrate of E1 moving mm/s

MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X 3000 #the Max acculeration of X printing mm/s^2
MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Y 3000 #the Max acculeration of Y printing mm/s^2
MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Z 500 #the Max acculeration of Z printing mm/s^2 MAX_ACCELERATION_EXT0 3000 #the Max acculeration of E0 printing mm/s^2 MAX_ACCELERATION_EXT1 3000 #the Max acculeration of E1 printing mm/s^2

MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X 1000 #MAX acceleration of X-axis moving mm/s^2
MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Y 1000 #MAX acceleration of Y-axis moving mm/s^2 MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Z 200 #MAX acceleration of Z-axis moving mm/s^2

---------------------------------------------------------------

################ Delta Settings ##############################

DELTA_MAX_RADIUS 135 #the radius of Delta annulus PRINTER_RADIUS 197 #the distance from machine center to vertical top DELTA_DIAGONAL_ROD 346.75 #the length of Delta pole DELTA_FLOOR_SAFETY_MARGIN_MM 15 #the safe distance of leveling edge

END_EFFECTOR_HORIZONTAL_OFFSET 28.0 # CARRIAGE_HORIZONTAL_OFFSET 14.5 # ROD_RADIUS 169 #

-------------------------------------------------------------

################## Advanced Settings#############################

cfg_insert_det_module 0 #Assemble power outage module (1:mks 220det;0:mks pwc)

cfg_have_ups_device 0 # UPS(1:yes;0:no)

cfg_print_over_auto_close 0 # auto-off when print finishes(1:yes；0:no)

cfg_filament_det_trigger_level 0 #the level signal of outage detection module (1:high level;0:low level)

cfg_filament_load_length 100 #the lenght to extrude filament (mm),Max:2000mm cfg_filament_load_speed 800 #the speed to extrude filament(mm/min) cfg_filament_load_limit_temperature 200 #It is the minimum temperature to extrude filament .

cfg_filament_unload_length 100 #the length to retract filament(mm),Max:2000mm cfg_filament_unload_speed 800 #the speed to retract filament(mm/min) cfg_filament_unload_limit_temperature 200 #It is the minimum temperature to retract filament .

-------------------------------------------------------------

################# Bed Leveling #############################

Leveling mode settings

cfg_leveling_mode 1 #1:auto-leveling; 0:manual leveling

########## Manual Leveling #############

manual leveling

cfg_point_number 5 #the point number of manual leveling(3,4,5 point available)

the 5 point location of manual leveling

cfg_point1:50,50 cfg_point2:180,50 cfg_point3:180,180 cfg_point4:50,180 cfg_point5:150,150

########### Auto Leveling ##############

cfg_auto_leveling_cmd:G28;G32 S2; #the setting of auto-leveling command button

FEATURE_Z_PROBE 1 #0:disable leveling，1:enable leveling BED_LEVELING_METHOD 1 #0:3 points leveling,1:more points leveling,2: 4 points leveling Z_PROBE_ON_HIGH 1 #Probe signal(0: low level,always on; 1:high level,always off) Z_PROBE_HEIGHT -0.8 #the height difference between Z-probe and nozzle Z_PROBE_X1 -90 #coordinateX1 is preset point Z_PROBE_Y1 -90 #coordinateY1 is preset point Z_PROBE_X2 90 #coordinateX2 is preset point Z_PROBE_Y2 -90 #coordinateY2 is preset point Z_PROBE_X3 -90 #coordinateX3 is preset point Z_PROBE_Y3 90 #coordinateY3 is preset point

cfg_leveling_z_speed 1500 #the speed of Z moving when manual leveling(mm/min) cfg_leveling_xy_speed 3000 #the speed of XY moving when manual leveling (mm/min)

BED_LEVELING_GRID_SIZE 5 #leveling interval Z_PROBE_SPEED 30 #the speed of Z-probe Z_PROBE_XY_SPEED 100 #the speed of XY

---------------------------------------------------------------

################# Wireless #####################################

cfg_wifi_mode:1 #wifi mode(0:sta;1:ap)

cfg_wifi_ap_name:MKS-WIFI #wifi name

cfg_wifi_key_code:makerbase #wifi password

cfg_cloud_enable:1 #0:disable cloud service 1:enable cloud service

cfg_wifi_cloud_host:www.baizhongyun.cn #cloud service adress

cfg_cloud_port:10086 #cloud service port

----------------------------------------------------------------

############### Special Setup(default) ######################

STEPPER_HIGH_DELAY 0 #Pulse hold time setting(unit: us)

For inverting stepper enable pins

X_ENABLE_ON 0 Y_ENABLE_ON 0 Z_ENABLE_ON 0 EXT0_ENABLE_ON 0 EXT1_ENABLE_ON 0

Type of heat manager for this extruder.

- 0 = Simply switch on/off if temperature is reached.

- 1 = PID Temperature control.

- 3 = Dead-time control.

EXT0_HEAT_MANAGER 1 # EXT1_HEAT_MANAGER 1 #

the PID setting of extruder

EXT0_PID_INTEGRAL_DRIVE_MAX 230 #the Max value of PID integral saturation EXT0_PID_INTEGRAL_DRIVE_MIN 40 #the Min value of PID integral saturation EXT0_PID_P 24 #the setting of P value EXT0_PID_I 0.88 #the setting of I value EXT0_PID_D 80 #the setting of D value

EXT1_PID_INTEGRAL_DRIVE_MAX 230 #the Max value of PID integral saturation EXT1_PID_INTEGRAL_DRIVE_MIN 40 #the Min value of PID integral saturation EXT1_PID_P 24 #the setting of P value EXT1_PID_I 0.88 #the setting of I value EXT1_PID_D 80 #the setting of D value

-------------------------------------------------------------

####### Display Effect(refer to MKS TFT datasheet) ###########

user-defined function1 and 2

setmenu_func1_display 1 #1:display this button，0:no setmenu_func2_display 0 #1:display this button; 0:not display

each command must be separated by semicolon ";"

setmenu_func1:M84; setmenu_func2:M81;

moreitem_pic_cnt 0 #the number of "more" button

edit command for 1~7 "More" button

each command must be separated by semicolon ";"

each icon command must be less than 200 bytes

moreitem_button1_cmd:G28 X0;G28 Y0;G28 Z0;

moreitem_button2_cmd:G28 X0;G28 Y0;G28 Z0;

moreitem_button3_cmd:G28 X0;G28 Y0;G28 Z0;

moreitem_button4_cmd:G28 X0;G28 Y0;G28 Z0;

moreitem_button5_cmd:G28 X0;G28 Y0;G28 Z0;

moreitem_button6_cmd:G28 X0;G28 Y0;G28 Z0;

moreitem_button7_cmd:G28 X0;G28 Y0;G28 Z0;

the number of "more" button to dispaly on printing interface

morefunc_cnt:0

button1~button6 function

morefunc1_cmd:G28; morefunc2_cmd:G28; morefunc3_cmd:G28; morefunc4_cmd:G28; morefunc5_cmd:G28; morefunc6_cmd:G28;

----------------------------------------------------------------

############## Display Customization #######################

cfg_background_color 0x000000 #the color of screen background

cfg_title_color 0xFFFFFF #the color of title text

cfg_state_background_color 0x000000 #the color of temperature,fan,(etc)background

cfg_state_text_color 0xFFFFFF #the color of temprature,fan,(etc) text

cfg_filename_background_color 0x000000 #the color of file button

cfg_filename_color 0xFFFFFF #the color of file text

cfg_printingstat_word_background_color 0x000000 #the color of background in printing status

cfg_printingstat_word_color 0xFFFFFF #the color of text in printing status

cfg_BUTTON_3D_effects 0 #3D effects setting (disable: 0, enable: 1)

[makerbase-mks]

HI The direction you set back to zero is this X_HOME_DIR 1 #Homing direction(-1:MIN,1:MAX) Y_HOME_DIR -1 #Homing direction(-1:MIN,1:MAX) Z_HOME_DIR 1 #Homing direction(-1:MIN,1:MAX) That is, x and z will reverse max, y back to min direction

But you enable the hardware limit but enable xyz to be the minimum limit.

1 for Min/Max endstop enable in hardware, while 0 disable

MIN_HARDWARE_ENDSTOP_X 1 MIN_HARDWARE_ENDSTOP_Y 1 MIN_HARDWARE_ENDSTOP_Z 1 MAX_HARDWARE_ENDSTOP_X 0 MAX_HARDWARE_ENDSTOP_Y 0 MAX_HARDWARE_ENDSTOP_Z 0

Therefore, it is said that the limit does not work. For example, if you set x to max, but you are exposed to the xmin limit switch, or a max switch that is not enabled, it is not normal.

If you want to press your direction of zero return, the limit you enable should be like this

1 for Min/Max endstop enable in hardware, while 0 disable

MIN_HARDWARE_ENDSTOP_X 0 MIN_HARDWARE_ENDSTOP_Y 1 MIN_HARDWARE_ENDSTOP_Z 0 MAX_HARDWARE_ENDSTOP_X 1 MAX_HARDWARE_ENDSTOP_Y 0 MAX_HARDWARE_ENDSTOP_Z 1

If wiring, you should also connect to the corresponding interface of min or max on the motherboard.

[maocastillo]

Hi. I am developing a large format printer and I use the MKS ROBIN v2.4 board. I do the configuration of the board (firmware) and it works very well, but I turn off the machine and turn it on again and the configuration is lost and returns to the factory firmware. I have changed several SD cards of various types and the same thing always happens, there is no firmware left on the board, the same thing happens to it. I appreciate your help thanks

[github051]

How to change the jerk settings ?

[Drakstein]

I have a simple question about the voltage of the MKS ROBIN v2.4 board, it suports input 24V, but it also outputs 24V?? By the way, I will use a BL touch, anyone here already used it, any suggestions? I will use in a core XY model.