TCWC
commented
5 years ago -------------------------------------------------------------
############ Based Settings( Required) #######################
machine type
0:xyz
1:corexy(x_motor = x+y, y_motor = x-y),
2:corexy(x_motor = x+y, y_motor = y-x),
3:delta
DRIVE_SYSTEM 0 #machine type
cfg_multiple_language 1 #multi-language(enable:1, disable:0)
cfg_language_type 3 #languages setting,this configuration is valid when "cfg_multiple_language" is disabled.
(simplified Chinese:1; traditional Chinese:2; English:3; Russian:4; Spanish:5;French:6;Italian:7).
NUM_EXTRUDER 1 #number of extruder (1:singal£»2:dual) HAVE_HEATED_BED 1 #1:enable bed; 0:disable bed EXT0_TEMPSENSOR_TYPE 1 #1:100k thermistor£»102: MAX31855 thermocouple EXT1_TEMPSENSOR_TYPE 1 #1:100k thermistor£»102: MAX31855 thermocouple HEATED_BED_SENSOR_TYPE 1 #1:100k thermistor£»
FEATURE_TWO_XSTEPPER 0 #change E1 singal into X , then dual X is available(enable:1; disable: 0) FEATURE_TWO_YSTEPPER 0 #change E1 singal into Y , then dual Y is available(enable:1; disable: 0) FEATURE_TWO_ZSTEPPER 0 #change E1 singal into Z , then dual Z is available(enable:1; disable: 0)
---------------------------------------------------------------
################# Machine settings ############################
EXT1_X_OFFSET 0 #E1 offset from the origin of X axis (mm) EXT1_Y_OFFSET 0 #E1 offset from the origin of Y axis (mm)
INVERT_X_DIR 1 #X motor direction, 1 goes opposite direction; INVERT_Y_DIR 1 #Y motor direction, 1 goes opposite direction;
INVERT_Z_DIR 0 #Z motor direction, 1 goes opposite direction;
EXT0_INVERSE 1 #E0motor direction, 1 goes opposite direction; EXT1_INVERSE 0 #E1motor direction, 1 goes opposite direction;XAXIS_STEPS_PER_MM 100 #X steps per mm YAXIS_STEPS_PER_MM 100 #Y steps per mm ZAXIS_STEPS_PER_MM 400 #Z steps per mm EXT0_STEPS_PER_MM 100 #E0 steps per mm EXT1_STEPS_PER_MM 100 #E1 steps per mm
X_MAX_LENGTH 220 #the MAX X-axis distance Y_MAX_LENGTH 220 #the MAX Y-axis distance Z_MAX_LENGTH 300 #the MAX Z-axis distance X_MIN_POS 0 #the MIN X-axis distance Y_MIN_POS 0 #the MIN Y-axis distance Z_MIN_POS 0 #the MIN Z-axis distance
MIN_EXTRUDER_TEMP 175 #MIN TEMP on Extruder ,play a protective role MAX_EXTRUDER_TEMP 275 #MAX TEMP on Extruder ,play a protective role MAX_HEATED_BED_TEMP 150 #MAX TEMP on heated bed £¬play a protective role
HOMING_ORDER 1 #Set direction of endstops when homing;
X_HOME_DIR -1 #Homing direction(-1:MIN£¬1:MAX) Y_HOME_DIR -1 #Homing direction(-1:MIN£¬1:MAX) Z_HOME_DIR -1 #Homing direction(-1:MIN£¬1:MAX)HOMING_FEEDRATE_X 40 #the feedrate on X homing HOMING_FEEDRATE_Y 40 #the feedrate on Y homing HOMING_FEEDRATE_Z 10 #the feedrate on Z homing
1 means endstop always-on,0 is always-off
ENDSTOP_X_MIN_INVERTING 1
ENDSTOP_Y_MIN_INVERTING 1
ENDSTOP_Z_MIN_INVERTING 1
ENDSTOP_X_MAX_INVERTING 0
ENDSTOP_Y_MAX_INVERTING 0
ENDSTOP_Z_MAX_INVERTING 0
1 for Min/Max endstop enable in hardware,while 0 disable
MIN_HARDWARE_ENDSTOP_X 1
MIN_HARDWARE_ENDSTOP_Y 1
MIN_HARDWARE_ENDSTOP_Z 1
MAX_HARDWARE_ENDSTOP_X 0
MAX_HARDWARE_ENDSTOP_Y 0
MAX_HARDWARE_ENDSTOP_Z 0
1 for Min/Max endstop enable in software,while 0 disable
min_software_endstop_x 0
min_software_endstop_y 0
min_software_endstop_z 0
max_software_endstop_x 1
max_software_endstop_y 1
max_software_endstop_z 1MAX_FEEDRATE_X 200 #the Max feedrate of X moving mm/s MAX_FEEDRATE_Y 200 #the Max feedrate of Y moving mm/s MAX_FEEDRATE_Z 50 #the Max feedrate of Z moving mm/s MAX_FEEDRATE_EXT0 200 #the Max feedrate of E0 moving mm/s MAX_FEEDRATE_EXT1 200 #the Max feedrate of E1 moving mm/s
MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X 3000 #the Max acculeration of X printing mm/s^2
MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Y 3000 #the Max acculeration of Y printing mm/s^2
MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Z 500 #the Max acculeration of Z printing mm/s^2 MAX_ACCELERATION_EXT0 3000 #the Max acculeration of E0 printing mm/s^2 MAX_ACCELERATION_EXT1 3000 #the Max acculeration of E1 printing mm/s^2MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X 1000 #MAX acceleration of X-axis moving mm/s^2
MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Y 1000 #MAX acceleration of Y-axis moving mm/s^2 MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Z 200 #MAX acceleration of Z-axis moving mm/s^2
---------------------------------------------------------------
################ Delta Settings ##############################
DELTA_MAX_RADIUS 135 #the radius of Delta annulus PRINTER_RADIUS 197 #the distance from machine center to vertical top DELTA_DIAGONAL_ROD 346.75 #the length of Delta pole DELTA_FLOOR_SAFETY_MARGIN_MM 15 #the safe distance of leveling edge
END_EFFECTOR_HORIZONTAL_OFFSET 28.0 # CARRIAGE_HORIZONTAL_OFFSET 14.5 # ROD_RADIUS 169 #
-------------------------------------------------------------
################## Advanced Settings#############################
cfg_insert_det_module 0 #Assemble power outage module (1:mks 220det;0:mks pwc)
cfg_have_ups_device 0 # UPS(1:yes;0:no)
cfg_print_over_auto_close 0 # auto-off when print finishes(1:yes£»0:no)
cfg_filament_det_trigger_level 0 #the level signal of outage detection module (1:high level;0:low level)
cfg_filament_load_length 100 #the lenght to extrude filament (mm),Max:2000mm cfg_filament_load_speed 800 #the speed to extrude filament(mm/min) cfg_filament_load_limit_temperature 200 #It is the minimum temperature to extrude filament .
cfg_filament_unload_length 100 #the length to retract filament(mm),Max:2000mm cfg_filament_unload_speed 800 #the speed to retract filament(mm/min) cfg_filament_unload_limit_temperature 200 #It is the minimum temperature to retract filament .
-------------------------------------------------------------
################# Bed Leveling #############################
Leveling mode settings
cfg_leveling_mode 1 #1:auto-leveling; 0:manual leveling
########## Manual Leveling #############
manual leveling
cfg_point_number 5 #the point number of manual leveling(3,4,5 point available)
the 5 point location of manual leveling
cfg_point1:50,50 cfg_point2:180,50 cfg_point3:180,180 cfg_point4:50,180 cfg_point5:150,150
########### Auto Leveling ##############
cfg_auto_leveling_cmd:G28;G32 S2; #the setting of auto-leveling command button
FEATURE_Z_PROBE 1 #0:disable leveling£¬1:enable leveling BED_LEVELING_METHOD 1 #0:3 points leveling,1:more points leveling,2: 4 points leveling Z_PROBE_ON_HIGH 1 #Probe signal(0: low level,always on; 1:high level,always off) Z_PROBE_HEIGHT -0.8 #the height difference between Z-probe and nozzle Z_PROBE_X1 -90 #coordinateX1 is preset point Z_PROBE_Y1 -90 #coordinateY1 is preset point Z_PROBE_X2 90 #coordinateX2 is preset point Z_PROBE_Y2 -90 #coordinateY2 is preset point Z_PROBE_X3 -90 #coordinateX3 is preset point Z_PROBE_Y3 90 #coordinateY3 is preset point
cfg_leveling_z_speed 1500 #the speed of Z moving when manual leveling(mm/min) cfg_leveling_xy_speed 3000 #the speed of XY moving when manual leveling (mm/min)
BED_LEVELING_GRID_SIZE 5 #leveling interval Z_PROBE_SPEED 30 #the speed of Z-probe Z_PROBE_XY_SPEED 100 #the speed of XY
---------------------------------------------------------------
################# Wireless #####################################
cfg_wifi_mode:1 #wifi mode(0:sta;1:ap)
cfg_wifi_ap_name:MKS-WIFI #wifi name
cfg_wifi_key_code:makerbase #wifi password
cfg_cloud_enable:1 #0:disable cloud service 1:enable cloud service
cfg_wifi_cloud_host:www.baizhongyun.cn #cloud service adress
cfg_cloud_port:10086 #cloud service port
----------------------------------------------------------------
############### Special Setup(default) ######################
STEPPER_HIGH_DELAY 0 #Pulse hold time setting(unit: us)
For inverting stepper enable pins
X_ENABLE_ON 0 Y_ENABLE_ON 0 Z_ENABLE_ON 0 EXT0_ENABLE_ON 0 EXT1_ENABLE_ON 0
Type of heat manager for this extruder.
- 0 = Simply switch on/off if temperature is reached.
- 1 = PID Temperature control.
- 3 = Dead-time control.
EXT0_HEAT_MANAGER 1 # EXT1_HEAT_MANAGER 1 #
the PID setting of extruder
EXT0_PID_INTEGRAL_DRIVE_MAX 230 #the Max value of PID integral saturation EXT0_PID_INTEGRAL_DRIVE_MIN 40 #the Min value of PID integral saturation EXT0_PID_P 24 #the setting of P value EXT0_PID_I 0.88 #the setting of I value EXT0_PID_D 80 #the setting of D value
EXT1_PID_INTEGRAL_DRIVE_MAX 230 #the Max value of PID integral saturation EXT1_PID_INTEGRAL_DRIVE_MIN 40 #the Min value of PID integral saturation EXT1_PID_P 24 #the setting of P value EXT1_PID_I 0.88 #the setting of I value EXT1_PID_D 80 #the setting of D value
-------------------------------------------------------------
####### Display Effect(refer to MKS TFT datasheet) ###########
user-defined function1 and 2
setmenu_func1_display 1 #1:display this button£¬0:no setmenu_func2_display 1 #1:display this button; 0:not display
each command must be separated by semicolon ";"
setmenu_func1:M84; setmenu_func2:M81;
moreitem_pic_cnt 0 #the number of "more" button
edit command for 1~7 "More" button
each command must be separated by semicolon ";"
each icon command must be less than 200 bytes
moreitem_button1_cmd:G28 X0;G28 Y0;G28 Z0;
moreitem_button2_cmd:G28 X0;G28 Y0;G28 Z0;
moreitem_button3_cmd:G28 X0;G28 Y0;G28 Z0;
moreitem_button4_cmd:G28 X0;G28 Y0;G28 Z0;
moreitem_button5_cmd:G28 X0;G28 Y0;G28 Z0;
moreitem_button6_cmd:G28 X0;G28 Y0;G28 Z0;
moreitem_button7_cmd:G28 X0;G28 Y0;G28 Z0;
the number of "more" button to dispaly on printing interface
morefunc_cnt:0
button1~button6 function
morefunc1_cmd:G28; morefunc2_cmd:G28; morefunc3_cmd:G28; morefunc4_cmd:G28; morefunc5_cmd:G28; morefunc6_cmd:G28;
----------------------------------------------------------------
############## Display Customization #######################
cfg_background_color 0x000000 #the color of screen background
cfg_title_color 0xFFFFFF #the color of title text
cfg_state_background_color 0x000000 #the color of temperature,fan,(etc)background
cfg_state_text_color 0xFFFFFF #the color of temprature,fan,(etc) text
cfg_filename_background_color 0x000000 #the color of file button
cfg_filename_color 0xFFFFFF #the color of file text
cfg_printingstat_word_background_color 0x000000 #the color of background in printing status
cfg_printingstat_word_color 0xFFFFFF #the color of text in printing status
cfg_BUTTON_3D_effects 0 #3D effects setting (disable: 0, enable: 1)
3Dangel
I have a X3A and just installed the MKS Robin 2.4 w/ V2.0.7 firmware. I figured out how to change and update the config.txt file but i'm having a hard time figuring out what parameter in the config.txt file controls where the hot end stops after a all home cmd. X and Y goes to the end stops and stay. Then the Z goes down but not over the bed so it bottoms out.