markniu
commented
6 months ago Hello, you can fix this like this https://github.com/markniu/Bed_Distance_sensor/issues/47#issuecomment-1825045187 this is a problem in klipper for that there is only a few ids left now. I am trying to reduce the ids numbers that used by the sensor and will update that to github next.
ibrahimhakkicandan
when i try to make command with bdsensor installed it gives "Too many message ids make: *** [Makefile:84: out/compile_time_request.o] Error 255"
Here is the full log:
pi@mainsail:~/klipper $ make Creating symbolic link out/board Building out/autoconf.h Compiling out/src/sched.o Compiling out/src/command.o Compiling out/src/basecmd.o Compiling out/src/debugcmds.o Compiling out/src/initial_pins.o Compiling out/src/gpiocmds.o Compiling out/src/stepper.o Compiling out/src/endstop.o Compiling out/src/trsync.o Compiling out/src/adccmds.o Compiling out/src/spicmds.o Compiling out/src/sdiocmds.o Compiling out/src/i2ccmds.o Compiling out/src/pwmcmds.o Compiling out/src/buttons.o Compiling out/src/tmcuart.o Compiling out/src/neopixel.o Compiling out/src/pulse_counter.o Compiling out/src/lcd_st7920.o Compiling out/src/lcd_hd44780.o Compiling out/src/spi_software.o Compiling out/src/i2c_software.o Compiling out/src/thermocouple.o Compiling out/src/sensor_adxl345.o Compiling out/src/sensor_angle.o Compiling out/src/sensor_mpu9250.o Compiling out/src/sensor_lis2dw.o Compiling out/src/sensor_ldc1612.o Compiling out/src/sensor_bulk.o Compiling out/src/BD_sensor.o Compiling out/src/stm32/watchdog.o Compiling out/src/stm32/gpio.o Compiling out/src/stm32/clockline.o Compiling out/src/stm32/dfu_reboot.o Compiling out/src/generic/crc16_ccitt.o Compiling out/src/generic/armcm_boot.o Compiling out/src/generic/armcm_irq.o Compiling out/src/generic/armcm_reset.o Compiling out/src/../lib/stm32f4/system_stm32f4xx.o Compiling out/src/stm32/stm32f4.o Compiling out/src/generic/armcm_timer.o Compiling out/src/stm32/gpioperiph.o Compiling out/src/stm32/adc.o Compiling out/src/stm32/i2c.o Compiling out/src/stm32/spi.o Compiling out/src/stm32/sdio.o Compiling out/src/stm32/usbotg.o Compiling out/src/stm32/chipid.o Compiling out/src/generic/usb_cdc.o Compiling out/src/stm32/hard_pwm.o Building out/compile_time_request.o Too many message ids make: *** [Makefile:84: out/compile_time_request.o] Error 255
if i uninstal with the script provided, the make command runs succesfully printer: ender 3 s1 pro make menuconfig: Enable extra low-level configuration options not checked Micro-controller Architecture (STMicroelectronics STM32) Processor model (STM32F401) Bootloader offset (64KiB bootloader) Communication interface (USB (on PA11/PA12))