pymcuprog reports upload success but is not uploading code

[paulskirk53]

Hi, Apologies for a long post but the background is important. I use a pair of AVR 4809 (40 pin variants) in a project. I use FTDI boards to facilitate code uploads and serial comms between a windows PC running my code and the AVRs. I use the Platformio IDE. When I started with the 4809s it was my first experience of UPDI and I found pyupdi, which in those days was not deprecated. It worked fine as installed in my platformio IDE. I subsequently started using pymcuprog when pyupdi became deprecated, but as it is much slower to upload code than pyupdi, I reverted to pyupdi. So the problem is that (for a reason I am exploring with the Platformio folks), pyupdi periodically disappears from my IDE. When this happens, I use pymcuprog as follows:

pymcuprog write -d atmega4809 -t uart -u COM3 -c 250k -f .pio\build\ATmega4809\firmware.hex

and it reports success when uploading code. However, I don't think the code uploads. A simple blinkled prog. used as a trial does not blink the LED. Naturally to start with I thought it was me, but today I managed to reinstall pyupdi and used that to upload the same blinkled code. It worked, so just out of curiosity, I used pymcuprog to upload the code and that seemed to work too as reported below:

PS C:\Users\Paul\Documents\PlatformIO\Projects\Arduino-code-blinkled> pymcuprog write -d atmega4809 -t uart -u COM3 -c 250k -f .pio\build\ATmega4809\firmware.hex Pinging device... Ping response: 1E9651 Writing from hex file... Writing flash... Done.

But it doesn't.

So I think all the above can be summarised as follows: If I use pyupdi to upload code, that works. If I use pymcuprog, it doesn't work.

It's probably a setting I have missed. Thanks for any thoughts.

[xedbg]

Hi @paulskirk53 - pymcuprog allows for programming several segments in several sessions, and thus does not erase the device before programming.
Before release 3.13 the solution from platformio was to chain erase and program: pymcuprog erase && pymcuprog write In 3.13 the --erase switch was added which means it can be done in one operation using pymcuprog write --erase And if you are in doubt, use the --verify switch to check by read-back after programming. (The --erase is not done by default - we have too many [internal] use-cases which will need to be addressed if we change this behaviour)

[paulskirk53]

Ah, brill, thanks for the explanation.

[paulskirk53]

Hi, I have just come back to this using the Platformio CLI, and using this command pymcuprog write -d atmega4809 -t uart -u COM5 -c 250k -f .pio\build\ATmega4809\firmware.hex --erase I get the error: pymcuprog: error: unrecognized arguments: --erase

any help much appreciated.

[xedbg]

@paulskirk53 - please verify which version of pymcuprog you are running since this --erase switch was added not long ago. pymcuprog --version

[paulskirk53]

it is 3.13.3.166 I did pip install pymcuprog

earlier today. It did work with the --erase option after I posted in July. thanks for help.

[mraardvark]

That version was released in May... Are you sure there is not an older version in a venv inside platformio?

[paulskirk53]

sorry I wouldn't know how to check, is there a command I can use to check for a virtual env.? Perhaps I should post about that on the PIO forum?

[mraardvark]

I guess easiest would be to replace the programming flash write call in your .ini file with pymcuprog --version and check the output from that...

[paulskirk53]

i was never able to get pymcuprog working via the platformio.ini file, so I use it from the CLI. So I removed --erase and used this: pymcuprog write -d atmega4809 -t uart -u COM5 -c 250k -f .pio\build\ATmega4809\firmware.hex --version

and it reports pymcuprog version 3.13.3.166

hope that helps.

[paulskirk53]

works fine this morning, no probs uploading with --erase. Only difference is the machine was restarted this morning. Version number is the same. Thanks for help.