mod-audio mod-hw-duoX issues

mod-audio / mod-hw-duoX

Hardware project of MOD Duo X

0 stars 0 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

3399 jd4 som

#41 Janjhl closed 3 years ago
0
create a keepout area on the pads connected to the audio grounding track

#40 odurc closed 7 years ago
0
remove copper from the area where screws touch the board

#39 odurc closed 7 years ago
0
very slightly increase all screw holes

#38 odurc opened 8 years ago
0
remove the 4 external holes

#37 odurc opened 8 years ago
0
remove circuit to shutdown headphone

#36 odurc closed 7 years ago
0
bottom board PCB layout

#35 odurc closed 9 years ago
2
bottom board parts placement

#34 odurc closed 9 years ago
1
update top board schematics

#33 odurc closed 9 years ago
2
update bottom board schematics

#32 odurc closed 9 years ago
1
swap i2S_SDIN/SDOUT signals

#31 felipesanches closed 9 years ago
0
Why is MCLK2 unused in the CODEC ?

#30 felipesanches closed 9 years ago
1
remove ASV-24.576MHz-EJ-T (XA1)

#29 felipesanches closed 9 years ago
0
check & maybe remove unused library dependencies

#28 felipesanches closed 9 years ago
1
verify which are the correct pins we should use for I2S signals

#27 felipesanches closed 9 years ago
0
Fix numbering of the PORT H bits in ICnovaA20 component

#26 felipesanches closed 9 years ago
0
do we need a pull up for the uboot-sel pin ?

#25 felipesanches closed 9 years ago
1
Create ICnova A20 schematic component

#24 felipesanches closed 9 years ago
0
Certify that all resistors in the audio circuit are metal film

#23 odurc closed 9 years ago
2
Add a README.md

#22 felipesanches closed 9 years ago
0
Improve mod-duo pcb grounding by attaching the connectors to DGND copper plane

#21 felipesanches closed 9 years ago
0
We shouldn't have different hw revisions separated by directories. Delete the old ones.

#20 felipesanches closed 9 years ago
2
Add a connector with all unused SODIMM signals

#19 felipesanches closed 9 years ago
1
Add a connector with the pins for an external (optional) SD card interface

#18 felipesanches closed 9 years ago
3
Create ITEAD AW204x schematic component

#17 felipesanches closed 9 years ago
0
Create a SODIMM-204 footprint

#16 felipesanches closed 9 years ago
1
change the sch/pcb to new SODIMM coreboard

#15 odurc closed 9 years ago
2
remove control chain HMI interface

#14 odurc closed 10 years ago
0
remove UI UART from both boards

#13 odurc closed 10 years ago
0
Implement differential balanced outputs (stretch goal)

#12 felipesanches closed 9 years ago
4
BottomBoard PCB and Netlist are out-of-sync

#11 felipesanches closed 10 years ago
1
Apply "RC1" git-tag to the last commit before July 28th, 2014

#10 felipesanches closed 10 years ago
1
Change the kind of connector used in the JTAG interface

#9 felipesanches closed 10 years ago
3
Rename serial interface signal names

#8 felipesanches closed 10 years ago
5
Choose which coreboard to use in the next pcb revision

#7 felipesanches closed 10 years ago
4
implement full-duplex for the control-chain interface

#6 felipesanches closed 9 years ago
3
new firmware loading interface/protocol

#5 felipesanches closed 10 years ago
1
rename signals in schem & pcb

#4 felipesanches closed 10 years ago
3
HMI flat cable pinout is swapped

#3 felipesanches closed 10 years ago
0
R18: why do we need this pulldown resistor?

#2 felipesanches closed 10 years ago
0
wrong footprint for 6N137 (U7)

#1 felipesanches closed 10 years ago
1