cant find coins on trezor after monero gui update

[ofiryy]

i had monero gui from 2 years ago, so i uninstalled it, and installed the lated version 0.18.3.3, i accessed the gui and restored from trezor device, now i see all the coins are gone, the balance is 0. could i have created by aacident a new monero wallet from trezor? what can i do to access the old coins?

[selsta]

Do you still have the old wallet file?

What does it say inside Settings -> Info -> Wallet restore height?

[ofiryy]

i dont think i have any old file, i uninstalled the old gui, and also manually deleted its directory, i wanted to start fresh with the latest monero gui. the wallet restore hight is 1. i use remote node

[selsta]

What does it say in Settings -> Info -> Wallet mode?

What does it say in the bottom left corner? Wallet is synchronized or is it still syncing?

[ofiryy]

wallet mode is advanced mode (remote node) wallet still syncing

[selsta]

You have to let the wallet finish syncing first before the funds show up.

[ofiryy]

i use node.moneroworld.com:18089 is it ok? how much time should it take ?

[selsta]

If it syncs blocks then the node is ok. I don't know how long it will take, it depends on your internet speed, your CPU, the speed of the node, etc.

In the future it would be better to set a restore height that is higher than 1 but still lower than your first received transactions to speed up the process.

[ofiryy]

can i change the restore height while it is syncronizing ?

[selsta]

In theory yes, but it would be best to just let it sync now before you enter a wrong restore height.

[ofiryy]

the remote node has finished syncronizing and still i see 0 in balance, so i switched to local node, network status is connected, ans still 0 balance. i had changed the resore hight to a date 2021-04-04, could it be the problem ?

[selsta]

Please stay on remote node, you don't have a synced local node so use remote node instead.

i had changed the resore hight to a date 2021-04-04, could it be the problem ?

What does it say under Settings -> Info -> Restore height? Share the exact value.

[ofiryy]

Wallet restore height: 2311108

[selsta]

Did you setup a passphrase on your Trezor that you previously did not have?

Did you let it sync on a remote node until 0 blocks were remaining before you switched to local node?

[ofiryy]

i did not setup any passphrase. not before and not now. with the remote node - it finished syncronizing, i mean, the "Syncronizing" was replaced with "Remote node", so i understood from this that it finished syncronizing (btw at that point the Wallet restore height was: 2311108) and i still had only 0 funds. but after the "Syncronizing" was replaced with "Remote node", i dont know to say how many blocks were remaining.

[ofiryy]

@selsta now, with local node, after hours of syncronizing, i have the "Connected" status, Wallet restore height: 2311108 and still 0 funds. what can i do to access my funds ?

[selsta]

@ofiryy go to Settings -> Log, type "status" into the textbox and post the output here.

[ofiryy]

i found the funds! i just needed to "open wallet from file" and then go the first wallet. i had like 3 wallets there, the 3rd one i created yesterday, i didnt know it actually kept some files from the old wallet, i didnt know it works like that. so i send some funds to another address- and complete the approvel process on trezor - it went well, but it seems stuck on "Sending transaction..." what do you think is the issue ? thanks

[selsta]

Please do what I suggested in my last comment. I need to know the status of the daemon.

[ofiryy]

i had to restart the gui because it was stuck, here is the output:

[4/4/2024 11:23 PM] 2024-04-04 20:23:45.145 I Monero 'Fluorine Fermi' (v0.18.3.3-release) Height: 3120194, target: 3120202 (99.9997%) Downloading at 3 kB/s 4 peers Remote Host Peer_ID State Prune_Seed Height DL kB/s, Queued Blocks / MB 24.90.16.82:18080 0000000000000000 before_handshake 0 0 0 kB/s, 0 blocks / 0 MB queued 135.181.86.255:18080 1cee5a28ef1d2f26 normal 180 3120202 1 kB/s, 0 blocks / 0 MB queued 76.237.91.67:18089 a2134f97838eea72 normal 0 3120202 1 kB/s, 0 blocks / 0 MB queued 185.165.170.162:18080 bed0e8f96e1b2b8b normal 0 3120202 1 kB/s, 0 blocks / 0 MB queued 0 spans, 0 MB []

status [4/4/2024 11:25 PM] 2024-04-04 20:24:26.904 I Monero 'Fluorine Fermi' (v0.18.3.3-release) Height: 3120202/3120202 (100.0%) on mainnet, bootstrapping from 5.78.103.116:18089, local height: 3120194 (99.9%), not mining, net hash 2.04 GH/s, v16, 0(out)+0(in) connections [4/4/2024 11:25 PM] 2024-04-04 20:24:41.039 I Monero 'Fluorine Fermi' (v0.18.3.3-release) Height: 3120202/3120202 (100.0%) on mainnet, bootstrapping from 5.78.103.116:18089, local height: 3120194 (99.9%), not mining, net hash 2.04 GH/s, v16, 0(out)+0(in) connections

[selsta]

Height: 3120194, target: 3120202 (99.9997%)

It has to be at 100% for everything to work correctly.

[ofiryy]

now i confirmd that it was 100%, and the transaction still get stuck...how long can it take ?

[selsta]

I'm confused how you were even able to create that transaction because as long as your node isn't at 100% you can't create one. Did you switch to a remote node for it?

now i confirmd that it was 100%

Get the transaction ID, go to Settings -> Log and enter

relay_tx txid

with txid being your transaction id.

[ofiryy]

its so weird, i let the trasaction be stuck for like 15 min, and now i see that it succeeded, i see the funds in the target adress, but the gui is still stuck.

i would send you the log you asked, but i dont have the transaction id. this wallet need some work to be more stable - but your support is fantastic, thank you very much

[johnr365]

@ofiryy - maybe try out the (Monero only) wallet called Feather Wallet in the future. It supports Trezor hardware wallets, and some people prefer it to the GUI wallet.