No Stream Will load

[MattEllison95]

All of my cameras refuse to send a consistent stream. What it will do is send 3 seconds at a time and then freeze for 2 minutes and do the same thing. I can't get a stream out of most of the cameras, as VLC will just straight up not connect to it half of the time.

I am using the latest version and Unraid to host the docker.

Logs seem to indicate this:

2022/12/12 12:50:02 [RTSP][DRIVEWAY] ✅ '/driveway' stream is UP! (3/3) 2022/12/12 12:50:02 [RTSP][DRIVEWAY] 📖 New client reading 2022/12/12 12:50:03 [WyzeBridge] 🎉 Connecting to WyzeCam V3 - front on 10.0.0.240 (1/3) 2022/12/12 12:50:03 [3D Printer] IOTC_ER_DEVICE_OFFLINE 2022/12/12 12:50:04 [WyzeBridge] 👻 3d-printer offline. WILL retry in 10s. 2022/12/12 12:50:04 [Front] IOTC_ER_DEVICE_OFFLINE 2022/12/12 12:50:04 [WyzeBridge] 👻 3d-printer offline. WILL retry in 10s. 2022/12/12 12:50:04 [Front] IOTC_ER_DEVICE_OFFLINE 2022/12/12 12:50:05 [WyzeBridge] 👻 front offline. WILL retry in 10s. 2022/12/12 12:50:06 [Outside Kitty] FFMPEG stopped 2022/12/12 12:50:07 [WyzeBridge] [ON-DEMAND] ⌛️ WyzeCam Outdoor - outside-kitty on 192.168.200.107 (1/3) 2022/12/12 12:50:07 [WyzeBridge] [ON-DEMAND] ⌛️ WyzeCam Outdoor - outside-kitty on 192.168.200.107 (1/3) 2022/12/12 12:50:12 [RTSP][DRIVEWAY] 📕 Client stopped reading 2022/12/12 12:50:12 [WyzeBridge] 192.168.191.28 - - [12/Dec/2022 12:50:12] "GET /img/driveway.jpg HTTP/1.1" 200 - 2022/12/12 12:50:13 [Driveway] WARNING: Wrong resolution (frame_size=1) 2022/12/12 12:50:13 [Driveway] Requesting frame_size=0 and bitrate=120 2022/12/12 12:50:14 [Driveway] WARNING: Skipping smaller frame at start of stream (frame_size=1) 2022/12/12 12:50:14 [WyzeBridge] 🎉 Connecting to WyzeCam V2 - 3d-printer on 10.0.0.98 (1/3) 2022/12/12 12:50:15 [WyzeBridge] 🎉 Connecting to WyzeCam V3 - front on 10.0.0.240 (1/3) 2022/12/12 12:50:15 [3D Printer] IOTC_ER_DEVICE_OFFLINE 2022/12/12 12:50:15 [WyzeBridge] 🎉 Connecting to WyzeCam V3 - front on 10.0.0.240 (1/3) 2022/12/12 12:50:15 [3D Printer] IOTC_ER_DEVICE_OFFLINE 2022/12/12 12:50:15 [Driveway] WARNING: AV_ER_INCOMPLETE_FRAME 2022/12/12 12:50:16 [WyzeBridge] 👻 3d-printer offline. WILL retry in 10s. 2022/12/12 12:50:16 [Front] IOTC_ER_DEVICE_OFFLINE 2022/12/12 12:50:17 [WyzeBridge] 👻 front offline. WILL retry in 10s. 2022/12/12 12:50:17 [WyzeBridge] 👻 front offline. WILL retry in 10s. 2022/12/12 12:50:22 [RTSP][DRIVEWAY] ❌ '/driveway' stream is down [tee @ 0x55e574183440] All tee outputs failed.

[mrlt8]

Hmm, does it work if you stream from a single camera at a time with ON_DEMAND=True?

[MattEllison95]

No it does not.

[lolgas]

I am having this issue on a fresh install within the last hour although its only effecting one cam. It loads for 2-3 seconds then buffers over and over. I see this in the log over and over:

wyze-bridge    | 2022/12/14 20:44:18 [RTSP][FRONT-DOOR-CAM] 📖 New client reading 
wyze-bridge    | 2022/12/14 20:44:23 [RTSP][FRONT-DOOR-CAM] 📕 Client stopped reading

[mrlt8]

Are the cameras on the latest firmware?

[lolgas]

According to the Wyze app - yes the cam is on 4.10.9.1574.