search

mrquincle / horizon

Horizon Box
44 stars 7 forks source link

log from uart #1

Open atarist opened 5 years ago

atarist commented 5 years ago

Splash: BMP found Width 720 Height 576

CEFDK Version : CE4200 5.800 (HT enabled) CEFDK Version-Samsung: SMT-G7400 6.4 Samsung Bootloader Version: SH-G7400DEUB-1006 8051 Firmware : B1-1.4.0 Silicon Stepping : C0 (FUSES) Board : Silver Grove CPU Threads : 2 CPU Multiplier : 16 CPU Bus Speed : 100 MHz Memory Size : 1024 MB Memory Type & Speed : x16 DDR3-1333 (10-10-10) Memory Configuration : A B Interleave Mode 1 PCI Mode : CE4200 Compatibility Boot Mode : NOR Media Device IRQ : 4

CEFDK Stage 1 version: 03/08/11 17:15:49 CEFDK Stage 2 version: 02/18/12 19:39:12

WARNING: Ancient bootloader, some functionality may be limited! starting pid 547, tty '': '/etc/init.d/rcS'

Starting Scripts

/etc/rc3.d/S003system_setup: line 62: syslogd: command not found /etc/rc3.d/S003system_setup SUCCESS Checking board... /etc/rc3.d/S006emmc SUCCESS Checking board... C0 box .. Checking board...

===>> Run /etc/rc3.d/S009onenand Script. insmod phram.ko insmod: can't insert '/lib/onenand_modules/phram.ko': Input/output error mount: mounting /dev/mtdblock7 on /root failed: No such device /etc/rc3.d/S009onenand: Unable to mount /dev/mtdblock7, Squashfs filesystem. VFS_format is 3 /etc/rc3.d/S009onenand SUCCESS flash or HDD root file system /etc/rc3.d/S012network SUCCESS /etc/rc3.d/S018kernel SUCCESS /etc/rc3.d/S024osal SUCCESS /etc/rc3.d/S027pal SUCCESS / LOAD "/etc/platform_config/ce4200/memory_layout_1G.hcfg" to (new) database lo cation "platform.memory.layout"/ shifting platform_config media_base_address 584 MB ( 0x24800000 ) / EXECUTE config database location "platform.startup"/ /etc/rc3.d/S030platform_config SUCCESS /etc/rc3.d/S033system_utils SUCCESS /etc/rc3.d/S036sven SUCCESS /etc/rc3.d/S039idl SUCCESS /etc/rc3.d/S042clock_control SUCCESS /etc/rc3.d/S045intel_ce_pm SUCCESS /etc/rc3.d/S048smd_core SUCCESS /etc/rc3.d/S051gentimer SUCCESS SOC is SOC_NAME_CE4200 /etc/rc3.d/S054sec SUCCESS [map( 0xdfb00000, 0x0007a000 ) = 0x6f94d000] [map( 0xdfb58000, 0x00080000 ) = 0x6f207000] [map( 0xdfb68000, 0x00080000 ) = 0x6f0e7000] /etc/rc3.d/S057display SUCCESS /etc/rc3.d/S060smd SUCCESS [map( 0xdf950000, 0x00010000 ) = 0x6ee78000] [map( 0xdf950000, 0x00007000 ) = 0x6ee71000] /etc/rc3.d/S063hdmi SUCCESS /etc/rc3.d/S066edl SUCCESS /etc/rc3.d/S069graphics SUCCESS /etc/rc3.d/S072directfb SUCCESS /etc/rc3.d/S075init_pic_uart SUCCESS

===>> Run /etc/rc3.d/S099Samsung Script. USB PHY drive strength port0 slope 011 amp 480mV, port1 slope 100 amp 460mV [Temperature check] init_socket() is called Current CPU temperature is 37 degrees C Fri Apr 1 00:00:00 UTC 2011 NOT AS Mode Normal Boot /etc/rc3.d/S099Samsung SUCCESS HW REVISION is 7 Checking if mab_monitor is running... Checking if drivers need to be unloaded... Loading mab with ... Loading oberon_upc_gateway with backend_enable_video_outputs=0 splash_enable=0 b sp_enable_atsc_usb=0 power_manager_delay=60 live_buffer_amt=27000 playback_buffe r_amt=12000 param_tuner_model=0 param_type_nvram=0 ... Creating device nodes Loading mab_monitor Setting kernel and monitor threads to NDS Fusion priority levels Changing scheduling parameters for init: pid 1, policy 2, priority 97 Changing scheduling parameters for kthreadd: pid 2, policy 2, priority 97 Changing scheduling parameters for ksoftirqd/0: pid 3, policy 2, priority 91 Changing scheduling parameters for ksoftirqd/1: pid 6, policy 2, priority 91 Changing scheduling parameters for events/0: pid 7, policy 2, priority 97 Changing scheduling parameters for events/1: pid 8, policy 2, priority 97 Changing scheduling parameters for khelper: pid 9, policy 2, priority 97 Changing scheduling parameters for async/mgr: pid 14, policy 2, priority 97 Changing scheduling parameters for kblockd/0: pid 111, policy 2, priority 91 Changing scheduling parameters for kblockd/1: pid 112, policy 2, priority 91 Changing scheduling parameters for khubd: pid 222, policy 2, priority 97 Changing scheduling parameters for kseriod: pid 225, policy 2, priority 97 Changing scheduling parameters for kmmcd: pid 228, policy 2, priority 97 Changing scheduling parameters for kswapd0: pid 353, policy 2, priority 97 Changing scheduling parameters for aio/0: pid 354, policy 2, priority 97 Changing scheduling parameters for aio/1: pid 355, policy 2, priority 97 Changing scheduling parameters for crypto/0: pid 356, policy 2, priority 91 Changing scheduling parameters for crypto/1: pid 357, policy 2, priority 91 Changing scheduling parameters for mtdblock0: pid 455, policy 2, priority 97 Changing scheduling parameters for mtdblock1: pid 460, policy 2, priority 97 Changing scheduling parameters for mtdblock2: pid 465, policy 2, priority 97 Changing scheduling parameters for mtdblock3: pid 470, policy 2, priority 97 Changing scheduling parameters for mtdblock4: pid 475, policy 2, priority 97 Changing scheduling parameters for mtdblock5: pid 480, policy 2, priority 97 Changing scheduling parameters for mtdblock6: pid 485, policy 2, priority 97 Changing scheduling parameters for ata_aux: pid 704, policy 2, priority 97 Changing scheduling parameters for ata_sff/0: pid 705, policy 2, priority 97 Changing scheduling parameters for ata_sff/1: pid 706, policy 2, priority 97 Changing scheduling parameters for scsi_eh_0: pid 711, policy 2, priority 97 Changing scheduling parameters for scsi_eh_1: pid 714, policy 2, priority 97 Changing scheduling parameters for gdl_server: pid 916, policy 2, priority 97 Changing scheduling parameters for CPU_Fan_Control: pid 1043, policy 2, priority 15 Changing scheduling parameters for scm_reverse_manager: pid 1060, policy 2, priority 97 Changing scheduling parameters for mab_monitor: pid 1121, policy 2, priority 15 disabling reserved schedule time for SCHED_OTHER FOS Baseline : Unknown

UPC Horizon Integration Launch script for Samsung Platforms Release version

--------------------- Release: Only usb key device detection ----------------- ----------------- ENVIRONEMENT VARIABLES ----------------

Drivers Rootfs: RAM NFS mount present: NO Execution from: FLASH Ethernet interface: br0 SCD_Process in /NDS: YES Perform mount on /NDS: NO Unified Args: NOCLEAN FATF/CI Target specified: Is FORMAT param detected: NO Build options detected: plt_samgw force_xbmc docsis XBMC ON XBMC forced by cmdline NO Telnet start NO

Is GDB DEBUG: NO Is DOCSIS Binary: YES Is USBLOG param detected: NO

----------------- Checking configuration ---------------- configuration is OK ------------------- mount management -------------------- ------------------- Release: bootlog process disabled --------------------- -------------------- unified startup call --------------- UNIFIED STARTUP mkdir: can't create directory '/fifo': File exists mkdir: can't create directory '/root': File exists copy_xtvfs_format_utility disable udev killall: udevd: no process killed firewall rules Bumping XTVFS priority pid 1305's current scheduling policy: SCHED_OTHER pid 1305's current scheduling priority: 0 pid 1305's new scheduling policy: SCHED_RR pid 1305's new scheduling priority: 91 ifconfig: SIOCSIFFLAGS: Cannot assign requested address ifconfig: SIOCSIFFLAGS: Cannot assign requested address ------------------- Release: bootlog process disabled --------------------- --------------------- Debug Information ----------------- ============ Kernel IP info .... ########## ROUTE : Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 224.0.0.0 0.0.0.0 240.0.0.0 U 0 0 0 br0 ########## ROUTE 6 : Kernel IPv6 routing table Destination Next Hop Flags Metric Ref Use Iface ########## IFCONFIG -A : br0 Link encap:Ethernet HWaddr 3C:62:00:76:A5:72 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

dummy0 Link encap:Ethernet HWaddr 3E:A7:88:ED:DB:60 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

eth0 Link encap:Ethernet HWaddr 3C:62:00:76:A5:72 UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:132 (132.0 B)

lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

########## mounting points : rootfs on / type rootfs (rw) proc on /proc type proc (rw,relatime) devpts on /dev/pts type devpts (rw,relatime,mode=600) none on /sys type sysfs (rw,relatime) tmpfs on /tmp type tmpfs (rw,relatime,size=40960k) usbfs on /proc/bus/usb type usbfs (rw,relatime,devgid=10000,devmode=664) tmpfs on /var type tmpfs (rw,relatime,size=8192k) /dev/stl0/11 on /vfs type ext3 (rw,relatime,errors=continue,barrier=1,data=journal) tmpfs on /fifo type tmpfs (rw,relatime) tmpfs on /dev/shm type tmpfs (rw,relatime) ########## PS : /NDS/start.sh: line 525: ps: command not found -------------- binary config file generation ------------

File diagctl.cfg at line 1 is not in SystemConfigFormat (skipping).

File webkit_whitelist.cfg at line 2 is not in SystemConfigFormat (skipping). -------------------- Release: Core dump disabled ---------------- ----------------- XBMC Management ----------------------- Change working directory to xbmc. XH : XH_Init XH : parent XH : Child XH : end parent --------------------- STB ID management ------------------ XH : end child select br0 interface *** CPE_IPADDR = ** --------------------- SCD_PROCESS Start ----------------- Change working directory to /NDS/bin Launching application... ------------------- Release: diagbinary process disabled --------------------- Starting normal mode trace log on terminal Called xpower_initialise(5) B'd rev_number = 7 HDD Sleep Timer Set HDD Sleep Timer Set(10min) Success Called xpower_get_capabilities Entering IPC_TL_SERVER_Init UPC Horizon Version Information: Release: 1b-263.011.0n (RELEASE) Build date: Oct 1 2013 15:00:51 Entering IPC_TL_SERVER_Init Entering IPC_TL_SERVER_Init Entering IPC_TL_SERVER_Init Called xpower_get_wake_up_cause POWER_MANAGER_GET_WAKEUP_CAUSE Called xpower_get_wake_up_cause = 0x0

: return_status = 0x00000001 : return_status = 0x770a97a8 : return_status = 0x00000001 : return_status = 0x770a542c : return_status = 0x770a132c NOCS 1.1 Chipset Security Driver, Version 1.1.0, Built Dec 3 2010, 11:02:44 : return_status = 0x7709d1e4 : return_status = 0x77098edc : return_status = 0x770949c4 : return_status = 0x77090860 : return_status = 0x7708c220 : return_status = 0x7707c750 : return_status = 0x770783f0 Entering IPC_TL_SERVER_Init /dev/sda2: recovering journal ▒fusion_pl_init in QFusionNoBlitPlatformIntegration Object::connect: No such signal Qt48Factory::sendEventSignal(QObject *, QEvent *) in qt48_factory.cpp:38 1881 inodes used (0.75%) 90 non-contiguous files (4.8%) 1 non-contiguous directory (0.1%) # of inodes with ind/dind/tind blocks: 23/1/0 55854 blocks used (5.57%) 0 bad blocks 1 large file 1866 regular files 6 directories 0 character device files 0 block device files 0 fifos 0 links 0 symbolic links (0 fast symbolic links) 0 sockets -------- 1872 files /dev/sda1: recovering journal 11 inodes used (0.01%) 0 non-contiguous files (0.0%) 0 non-contiguous directories (0.0%) # of inodes with ind/dind/tind blocks: 0/0/0 26556 blocks used (5.25%) 0 bad blocks 0 large files 0 regular files 2 directories 0 character device files 0 block device files 0 fifos 0 links 0 symbolic links (0 fast symbolic links) 0 sockets -------- 2 files Called xpower_set_deferred_state xPowerState = 0x8 devices = 0x4 Current_Power_State(0x1) , xPowerState=(0x8) Save the Ancillary_Device_Scheduled_State Called xpower_set_state xPowerState= 0x8 wakeupCause = 0x1cf XPOWER_ANCILLARY_SATA Power state -> 0 SATA_Control Start (0) => Same State, don't need to be set cmd = hdparm -y /dev/sda XPOWER_ANCILLARY_USB Power state -> 0 USB_Control Start (0) POWER_MANAGER_SET_USB_STATE 0x0 result 0x0, ONandOFF = 0x0 Power Manager was Same State with your request gpio control start POWER_MANAGER_SET_USB_STATE SUCCESS POWER_MANAGER_WAKE_UP_ALARM_CONTROL POWER_MANAGER_SET_POWER_STATE Called xpower_set_state xPowerState= 0x1 wakeupCause = 0x1cf XPOWER_ANCILLARY_SATA Power state -> 1 SATA_Control Start (1) POWER_MANAGER_SET_SATA_STATE (1) : OK! XPOWER_ANCILLARY_USB Power state -> 2 USB_Control Start (1) POWER_MANAGER_SET_USB_STATE 0x1 result 0x0, ONandOFF = 0x0 gpio control start POWER_MANAGER_SET_USB_STATE SUCCESS POWER_MANAGER_WAKE_UP_ALARM_CONTROL POWER_MANAGER_SET_POWER_STATE
creisey commented 3 years ago

my bootlog looks a bit different:

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2021.02.11 11:31:01 =~=~=~=~=~=~=~=~=~=~=~= Splash: BMP found Width 720 Height 576 Splash: BMP found Width 720 Height 576

CEFDK Version : CE4200 5.800 (HT enabled) CEFDK Version-Samsung: SMT-G7400 7.1 Samsung Bootloader Version: SH-G7400DEUB-2001 8051 Firmware : B1-1.4.15 Silicon Stepping : C0 (FUSES) Board : Silver Grove CPU Threads : 2 CPU Multiplier : 16 CPU Bus Speed : 100 MHz Memory Size : 1024 MB Memory Type & Speed : x16 DDR3-1333 (10-10-10) Memory Configuration : A B Interleave Mode 1 PCI Mode : CE4200 Compatibility Boot Mode : NOR Media Device IRQ : 4

CEFDK Stage 1 version: 03/08/11 17:15:49 CEFDK Stage 2 version: 06/24/13 12:41:41

WARNING: Ancient bootloader, some functionality may be limited!

starting pid 577, tty '': '/etc/init.d/rcS'

Starting Scripts

/etc/rc3.d/S003system_setup: line 62: syslogd: command not found /etc/rc3.d/S003system_setup SUCCESS Checking board... eMMC box .. Checking board...

===>> Run /etc/rc3.d/S006emmc Script. /etc/rc3.d/S006emmc SUCCESS Checking board... /etc/rc3.d/S009onenand SUCCESS flash or HDD root file system

skip /etc/rc3.d/S012network SUCCESS /etc/rc3.d/S018kernel SUCCESS /etc/rc3.d/S024osal SUCCESS /etc/rc3.d/S027pal SUCCESS / LOAD "/etc/platform_config/ce4200/memory_layout_1G.hcfg" to (new) database location "platform.memory.layout"/ shifting platform_config media_base_address 584 MB ( 0x24800000 ) / EXECUTE config database location "platform.startup"/ /etc/rc3.d/S030platform_config SUCCESS /etc/rc3.d/S033system_utils SUCCESS /etc/rc3.d/S036sven SUCCESS /etc/rc3.d/S039idl SUCCESS / SET_INT "5" to database location "platform.software.drivers.flash_appdata.mtd_device_number"/ / SET_INT "9" to database location "platform.hardware.revision"/ / SET_INT "0" to database location "platform.software.drivers.smd.clock.clock_properties.master_clock_source"/ / SET_INT "1" to database location "platform.software.drivers.smd.audio.vcxo_working"/ /etc/rc3.d/S042Samsung_platform_config SUCCESS /etc/rc3.d/S045clock_control SUCCESS /etc/rc3.d/S048intel_ce_pm SUCCESS /etc/rc3.d/S051smd_core SUCCESS /etc/rc3.d/S054gentimer SUCCESS SOC is SOC_NAME_CE4200 /etc/rc3.d/S057sec SUCCESS [map( 0xdfb00000, 0x0007a000 ) = 0x6f92b000] [map( 0xdfb58000, 0x00080000 ) = 0x6f1e5000] [map( 0xdfb68000, 0x00080000 ) = 0x6f0c5000] /etc/rc3.d/S060display SUCCESS /etc/rc3.d/S063smd SUCCESS [map( 0xdf950000, 0x00010000 ) = 0x6ee56000] [map( 0xdf950000, 0x00007000 ) = 0x6ee4f000] /etc/rc3.d/S066hdmi SUCCESS /etc/rc3.d/S069edl SUCCESS /etc/rc3.d/S072graphics SUCCESS /etc/rc3.d/S075directfb SUCCESS /etc/rc3.d/S078init_pic_uart SUCCESS

===>> Run /etc/rc3.d/S081Samsung Script. USB PHY drive strength port0 slope 011 amp 480mV, port1 slope 100 amp 460mV [Temperature check] Current CPU temperature is 45 degrees C Fri Apr 1 00:00:00 UTC 2011 NOT AS Mode Normal Boot /etc/rc3.d/S081Samsung SUCCESS HW REVISION is 9 Unloading mab_monitor if it is running... killall: mab_monitor: no process killed Checking if drivers need to be unloaded... Loading mab with ... Loading oberon_upc_gateway with backend_enable_video_outputs=0 splash_enable=0 bsp_enable_atsc_usb=0 power_manager_delay=3600 playback_buffer_amt=12000 audio_avsync_delay=4500 param_tuner_model=0 param_type_nvram=1 live_buffer_amt=7200 bufmon_underrun_amount=18000 bufmon_overrun_amount=18000 ... Creating device nodes Loading mab_monitor Setting kernel and monitor threads to NDS Fusion priority levels Changing scheduling parameters for init: pid 1, policy 2, priority 97 Changing scheduling parameters for kthreadd: pid 2, policy 2, priority 97 Changing scheduling parameters for ksoftirqd/0: pid 3, policy 2, priority 91 Changing scheduling parameters for ksoftirqd/1: pid 6, policy 2, priority 91 Changing scheduling parameters for events/0: pid 7, policy 2, priority 97 Changing scheduling parameters for events/1: pid 8, policy 2, priority 97 Changing scheduling parameters for khelper: pid 9, policy 2, priority 97 Changing scheduling parameters for async/mgr: pid 14, policy 2, priority 97 Changing scheduling parameters for kblockd/0: pid 112, policy 2, priority 91 Changing scheduling parameters for kblockd/1: pid 113, policy 2, priority 91 Changing scheduling parameters for ata_aux: pid 216, policy 2, priority 97 Changing scheduling parameters for ata_sff/0: pid 217, policy 2, priority 97 Changing scheduling parameters for ata_sff/1: pid 218, policy 2, priority 97 Changing scheduling parameters for khubd: pid 226, policy 2, priority 97 Changing scheduling parameters for kmmcd: pid 230, policy 2, priority 97 Changing scheduling parameters for kswapd0: pid 355, policy 2, priority 97 Changing scheduling parameters for aio/0: pid 356, policy 2, priority 97 Changing scheduling parameters for aio/1: pid 357, policy 2, priority 97 Changing scheduling parameters for crypto/0: pid 358, policy 2, priority 91 Changing scheduling parameters for crypto/1: pid 359, policy 2, priority 91 Changing scheduling parameters for scsi_eh_0: pid 442, policy 2, priority 97 Changing scheduling parameters for scsi_eh_1: pid 445, policy 2, priority 97 Changing scheduling parameters for mtdblock0: pid 463, policy 2, priority 97 Changing scheduling parameters for mtdblock1: pid 468, policy 2, priority 97 Changing scheduling parameters for mtdblock2: pid 473, policy 2, priority 97 Changing scheduling parameters for mtdblock3: pid 478, policy 2, priority 97 Changing scheduling parameters for mtdblock4: pid 483, policy 2, priority 97 Changing scheduling parameters for mtdblock5: pid 488, policy 2, priority 97 Changing scheduling parameters for mtdblock6: pid 493, policy 2, priority 97 Changing scheduling parameters for mtdblock7: pid 498, policy 2, priority 97 Changing scheduling parameters for mmcqd/0: pid 556, policy 2, priority 91 Changing scheduling parameters for mmcqd/0gp0: pid 557, policy 2, priority 91 Changing scheduling parameters for mmcqd/0gp1: pid 558, policy 2, priority 91 Changing scheduling parameters for gdl_server: pid 901, policy 2, priority 97 Changing scheduling parameters for CPU_Fan_Control: pid 1034, policy 2, priority 15 Changing scheduling parameters for scm_reverse_manager: pid 1054, policy 2, priority 97 Changing scheduling parameters for mab_monitor: pid 1119, policy 2, priority 15 disabling reserved schedule time for SCHED_OTHER

UPC Horizon Integration Launch script for Samsung Platforms Release version

--------------------- Release: Only usb key device detection ----------------- ----------------- ENVIRONEMENT VARIABLES ----------------

hard model: SMT-G7400 Drivers Rootfs: RAM NFS mount present: NO Execution from: FLASH Ethernet interface: br0 SCD_Process in /NDS: YES Perform mount on /NDS: NO Unified Args: NOCLEAN FATF/CI Target specified: Is FORMAT param detected: NO Build options detected: plt_samgw force_xbmc docsis cak_production XBMC ON XBMC forced by cmdline NO Telnet start NO

Is GDB DEBUG: NO Is DOCSIS Binary: YES Is USBLOG param detected: NO

----------------- Checking configuration ---------------- configuration is OK ------------------- mount management -------------------- ------------------- Release: bootlog process disabled --------------------- -------------------- unified startup call --------------- UNIFIED STARTUP PATCH : ipv6 autoconf must be disabled in IPv4 mode mkdir: can't create directory '/fifo': File exists mkdir: can't create directory '/root': File exists copy_xtvfs_format_utility disable udev killall: udevd: no process killed firewall rules Bumping XTVFS priority pid 1292's current scheduling policy: SCHED_OTHER pid 1292's current scheduling priority: 0 pid 1292's new scheduling policy: SCHED_RR pid 1292's new scheduling priority: 91 sed: /root/run.sh: No such file or directory ifconfig: SIOCSIFFLAGS: Cannot assign requested address ifconfig: SIOCSIFFLAGS: Cannot assign requested address ------------------- Release: bootlog process disabled --------------------- --------------------- Debug Information ----------------- ============ Kernel IP info .... ########## ROUTE : Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 224.0.0.0 0.0.0.0 240.0.0.0 U 0 0 0 br0 ########## ROUTE 6 : Kernel IPv6 routing table Destination Next Hop Flags Metric Ref Use Iface ########## IFCONFIG -A : br0 Link encap:Ethernet HWaddr 20:D5:BF:1A:84:2C
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

dummy0 Link encap:Ethernet HWaddr F2:ED:78:16:4D:33
BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

eth0 Link encap:Ethernet HWaddr 20:D5:BF:1A:84:2C
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:132 (132.0 B)

eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:20 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

########## mounting points : rootfs on / type rootfs (rw) proc on /proc type proc (rw,relatime) devpts on /dev/pts type devpts (rw,relatime,mode=600) none on /sys type sysfs (rw,relatime) tmpfs on /tmp type tmpfs (rw,relatime,size=40960k) usbfs on /proc/bus/usb type usbfs (rw,relatime,devgid=10000,devmode=664) tmpfs on /var type tmpfs (rw,relatime,size=8192k) /dev/mmcblk0p9 on /vfs type ext3 (rw,nosuid,nodev,noexec,relatime,errors=continue,barrier=1,data=journal) tmpfs on /fifo type tmpfs (rw,relatime) tmpfs on /dev/shm type tmpfs (rw,relatime) ########## PS : /NDS/start.sh: line 611: ps: command not found -------------- binary config file generation ------------

File diagctl.cfg at line 1 is not in SystemConfigFormat (skipping). -------------------- Release: Core dump disabled ---------------- ----------------- XBMC Management ----------------------- Change working directory to xbmc. XH : XH_Init XH : parent XH : Child XH : end parent --------------------- STB ID management ------------------ XH : end child select br0 interface * CPE_IPADDR_IPV4 = ** * CPE_IPADDR_LINK_IPV6 = ** *** CPE_IPADDR_GLOBAL_IPV6 = ** --------------------- SCD_PROCESS Start ----------------- Change working directory to /NDS/bin Launching application... ------------------- Release: diagbinary process disabled --------------------- Starting normal mode trace log on terminal

**The main function for the Middleware Starter Proces** INFO: MW_STARTER_ReadConfigValues: FILE: pwm.cfg INFO: MW_STARTER_ReadConfigValues: NAME: PWM_Process INFO: MW_STARTER_ReadConfigValues: PATH: /NDS/bin/PWM_Process INFO: MW_STARTER_ReadConfigValues: ARGS: INFO: MW_STARTER_ReadConfigValues: Arg 0: /NDS/bin/PWM_Process INFO: MW_STARTER_ReadConfigValues: Arg 1: PWM_Process INFO: MW_STARTER_SpawnProcess: Spawn /NDS/bin/PWM_Process INFO: MW_STARTER_SpawnProcess: Spawned pid 4761 PWM version: PWM:Feb 13 2015:HGH_F73.1.REL_HGH_UPC_MAIN_Int:RELEASE Called xpower_initialise(5) B'd rev_number = 9 Starting UPC Horizon Version Information: Release: 1b-3276.010.9 (RELEASE) Build date: Feb 13 2015 14:53:38

MW_Process MAIN Called xpower_get_wake_up_cause Called xpower_get_wake_up_cause = 0x1

: return_status = 0x00000001 : return_status = 0x00000001 NOCS 1.1 Chipset Security Driver, Version 1.1.0, Built Dec 3 2010, 11:02:44 Called xpower_get_capabilities  7e QT48PROXY_Init: CMC_WEBKITQT_CMCWK_TAG = cisco-4.8-cmc-0.24.REL QT48PROXY_Init: CMC_WEBKITQT_QT_TAG = cisco-4.8-cmc-0.24.REL QT48PROXY_Init: CMC_WEBKITQT_WEBKIT_TAG = cisco-4.8-cmc-0.24.REL fusion_pl_init in qfusionPlatformIntegration RAND_poll !!!!!!!!
creisey commented 3 years ago

my box was brand new "out of the box". its a shame that this thing is locked down. i'd love to run a debian on it and use it as Media Server or something else