Closed The4gotn1 closed 1 week ago
Try measuring your voltage at the d1 d2 intersection. Also at the input of the entire board.
Closing since it's not an issue with the project but your build. Happy to continue helping troubleshoot though, but I'll have limited ability until Tues when I'm back in my office
I get 3.04 v on the D1 leg closest to the edge of the board. But I get 0 on the D2 leg closest to the edge of the board.
From: Mark A. Stratman @.> Sent: Saturday, October 12, 2024 2:00:27 PM To: mstratman/vu-meter-driver @.> Cc: debra dreamcopyphoto.com @.>; Author @.> Subject: Re: [mstratman/vu-meter-driver] Meter doesnt retun to zero. (Issue #2)
Try measuring your voltage at the d1 d2 intersection. Also at the input of the entire board.
Closing since it's not an issue with the project but your build. Happy to continue helping troubleshoot though, but I'll have limited ability until Tues when I'm back in my office
— Reply to this email directly, view it on GitHubhttps://github.com/mstratman/vu-meter-driver/issues/2#issuecomment-2408661753, or unsubscribehttps://github.com/notifications/unsubscribe-auth/BMBXIZFT4WUX6JSJ3LFANILZ3FWUXAVCNFSM6AAAAABP2UMFJWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDIMBYGY3DCNZVGM. You are receiving this because you authored the thread.Message ID: @.***>
Sorry wrong pins. I get .263v on both.
From: debra dreamcopyphoto.com @.> Sent: Saturday, October 12, 2024 6:26:32 PM To: mstratman/vu-meter-driver @.>; mstratman/vu-meter-driver @.> Cc: Author @.> Subject: Re: [mstratman/vu-meter-driver] Meter doesnt retun to zero. (Issue #2)
I get 3.04 v on the D1 leg closest to the edge of the board. But I get 0 on the D2 leg closest to the edge of the board.
From: Mark A. Stratman @.> Sent: Saturday, October 12, 2024 2:00:27 PM To: mstratman/vu-meter-driver @.> Cc: debra dreamcopyphoto.com @.>; Author @.> Subject: Re: [mstratman/vu-meter-driver] Meter doesnt retun to zero. (Issue #2)
Try measuring your voltage at the d1 d2 intersection. Also at the input of the entire board.
Closing since it's not an issue with the project but your build. Happy to continue helping troubleshoot though, but I'll have limited ability until Tues when I'm back in my office
— Reply to this email directly, view it on GitHubhttps://github.com/mstratman/vu-meter-driver/issues/2#issuecomment-2408661753, or unsubscribehttps://github.com/notifications/unsubscribe-auth/BMBXIZFT4WUX6JSJ3LFANILZ3FWUXAVCNFSM6AAAAABP2UMFJWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDIMBYGY3DCNZVGM. You are receiving this because you authored the thread.Message ID: @.***>
Ordered your kit and components. I finished the build and when powered on the meter is already half way up. It then moves when I send a signal through it amd returns to half way up. Only when I pull the power does it return to 0.
Any ideas?