Closed fkey3 closed 6 years ago
i will look into the flow bug
Small update: MS13e receive RF commands do work. I created a “fake” ms13e device and named it after the RF signal that is send from my CM15pro. It nicely triggers the flow! So it seems signals that are not coupled to a device are not received anymore. But I use them a lot: X10 RF remote and I have my CM15pro send RF signals to homes for certain states. So my workaround is now: create a lot of MS13e devices to catch the RF Update: and make sure the ms13 is also set to Off, since its a switch a second “on” will not be captured
thats correct i am looking in to it
repaired in 2.0.4 is submitted to app store waiting approval
Thanks!! I’ll test it and then close the issue..
Just tested 2.05. Unfortunately still not working. RFcommands are send by my CM15pro This is working fine: This is not working:
and in 2.o.5 released yesterday evening
@nattlip , Hi Jilles, I tested it at 2.05.it did not function. Do I use it the wrong way (it did work like this before 2.02..)
but he receives d 6 on , but no ms13e commands, but the commandss send from the paired ms13e should be send to the device capabilitie. . i dont understnad what works and what not
i do iunderstand , i have a flow with a ms13e if he detects movement homey says something
this works
i ll check it tomorrow evening ,
it works with me the flow above works , if x10.2 recieves the above code from 433 signal homey speaks , i have now 2.05 from the app store. So i dont understand it is not working with you @fkey3
Tested again with the same flow as your example (speech), it works. Changed my flow to “received X10 command”, it works!😀
Dont know what went wrong yesterday (the screenshot shows exactly the same command I have now) Thanks for your patience! 😉
glad it works
Van: fkey3 notifications@github.com Verzonden: zondag 30 september 2018 21:53 Aan: nattlip/com.jilles.x10.2 CC: nattlip; Mention Onderwerp: Re: [nattlip/com.jilles.x10.2] X10 rf recieve no longer working (#3)
Tested again with the same flow as your example (speech), it works. Changed my flow to “received X10 command”, it works!😀
Dont know what went wrong yesterday (the screenshot shows exactly the same command I have now) Thanks for your patience! 😉
— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHubhttps://eur02.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Fnattlip%2Fcom.jilles.x10.2%2Fissues%2F3%23issuecomment-425746880&data=02%7C01%7C%7C72ff53d7a9ad47f077c208d6270e6666%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636739340125088176&sdata=GGIFScaKG5jJFhIhHKdKd2c1nehyrEfZxaDlmZJ4Pe8%3D&reserved=0, or mute the threadhttps://eur02.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Fnotifications%2Funsubscribe-auth%2FAGttxFjlhkWMZ3dcAvTqGV2Ch5t-Nzxiks5ugSE7gaJpZM4W13DE&data=02%7C01%7C%7C72ff53d7a9ad47f077c208d6270e6666%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636739340125088176&sdata=Jbqa4Ef6ENsyVcVorC97VnA%2FhnaPEcFCU61nVEz6tYM%3D&reserved=0.
I use an X13 transceiver. Sending commands to the AM12G appliance works perfectly. However... receiving X10 command does not. One of my on/off devices reacts on housecode D with ID 1, however if I create a flow that is triggered by D1 nothing happens. Can I test/debug something to help or am I doing something wrong?
Your hardware setup will not work: 1 homey is able to send and receive X10 RF commands, not X10 powerline commands. 2 your transceiver is able to transfer RF to powerline. So in your setup Homey is able to operate the X10 devices, but your setup is not able to create a RF command that homey can receive.
You need to add a device that sends X10-RF commands based on X10 powerline commands. I have a CM15pro that runs amacro based on recieved X10 powerline. The macro in its turn sends a X10 RF that is received by homey.
You can buy CM15pro cheap 2ndhand...
Clear! I was under the presumption that the X13 was a transceiver both ways. I'll pick up a CM15Pro somewhere.
Since the upgrade to v2.02 homey does not respond to recieve RF anymore. Removed the devices and created them again. When I drag x10 into the WHEN and out in a direct RF call the flow is not triggered. When I drag in a device into the WHEN with a recieve no trigger of the flow either
Worked perfectly fine until last week (before the update)