search

nberlee / talos

Friendly fork for Turing RK1 on Talos
https://www.talos.dev
Mozilla Public License 2.0
78 stars 0 forks source link

Unable to flash Talos 1.7.5 on RK1 modules in Turing Pi 2 #8

Closed ned-si closed 4 months ago

ned-si commented 4 months ago

Bug Report

Description

Hey there!

I built a Talos cluster on the Turing Pi 2 with 4 RK1 nodes a few weeks ago with Talos 1.6.3 using the image from this fork. For reasons (mainly me screwing up), I broke the cluster and wanted to start fresh and install the version 1.7.5, then use talhelper to go for Talos with Cilium without kube-proxy.

I downloaded the image and flashed it using the following command tpi --user root --password turing flash -i metal-turing_rk1-arm64.raw -n 1, then I tpi power on, and then I try to get the IP address using tpi uart get -n1 (or with the user/pass as well), but I get 0 answer. I tried to nmap my network but can't see the nodes there either.

Any idea what's wrong and where I can go from here to get things going again?

Thanks in advance for your insight!

Cheers

ps: Tried to flash the 1.6.3 again, but same result as well... 😦

Logs

Environment

ned-si commented 4 months ago

So, the issue is not with the image but with my cli it seems. Using the turingpi GUI to flash the nodes worked fine for some reason...

Well, it's not an issue with the image, so closing this. Sorry for bothering!

I was able to get the uart get command working twice, but then it didn't work anymore on any of the nodes.

Here's the output I got, in case it helps:

╰─ ❯ tpi uart get -n1
+ OK
## Checking hash(es) for Image fdt-1 ... sha256+ OK
## Checking hash(es) for Image atf-2 ... sha256+ OK
## Checking hash(es) for Image atf-3 ... sha256+ OK
INFO:    Preloader serial: 9
NOTICE:  BL31: v2.3():v2.3-589-g3389cfdda:derrick.huang
NOTICE:  BL31: Built : 10:14:29, May  9 2023
INFO:    spec: 0x1
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2024.01 (Jan 28 2024 - 19:39:18 +0000)

Model: Turing Machines RK1
DRAM:  32 GiB (effective 31.7 GiB)
Core:  318 devices, 27 uclasses, devicetree: separate
MMC:   mmc@fe2e0000: 0
Loading Environment from nowhere... OK
In:    serial@febc0000
Out:   serial@febc0000
Err:   serial@febc0000
Model: Turing Machines RK1
Net:   eth0: ethernet@fe1c0000
Hit any key to stop autoboot:  0
pcie_dw_rockchip pcie@fe180000: PCIe-0 Link Fail
pcie_dw_rockchip pcie@fe150000: PCIe-1 Link Fail
pcie_dw_rockchip pcie@fe180000: PCIe-0 Link Fail

╰─ ❯ tpi uart get -n1
_rkvdec2 fdc48100.rkvdec-core: core_mask=00020002
[   17.024502] mpp_rkvdec2 fdc48100.rkvdec-core: attach ccu as core 1
[   17.024796] mpp_rkvdec2 fdc48100.rkvdec-core: sram_start 0x00000000ff079000
[   17.024807] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_iova 0x00000000ffe00000
[   17.024817] mpp_rkvdec2 fdc48100.rkvdec-core: sram_size 487424
[   17.024827] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_size 1048576
[   17.024838] mpp_rkvdec2 fdc48100.rkvdec-core: min_width 512
[   17.024849] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_info_count 20
[   17.024859] mpp_rkvdec2 fdc48100.rkvdec-core: [136, 24576]
[   17.024868] mpp_rkvdec2 fdc48100.rkvdec-core: [137, 49152]
[   17.024877] mpp_rkvdec2 fdc48100.rkvdec-core: [141, 90112]
[   17.024886] mpp_rkvdec2 fdc48100.rkvdec-core: [140, 49152]
[   17.024896] mpp_rkvdec2 fdc48100.rkvdec-core: [139, 180224]
[   17.024905] mpp_rkvdec2 fdc48100.rkvdec-core: [133, 49152]
[   17.024914] mpp_rkvdec2 fdc48100.rkvdec-core: [134, 8192]
[   17.024924] mpp_rkvdec2 fdc48100.rkvdec-core: [135, 4352]
[   17.024933] mpp_rkvdec2 fdc48100.rkvdec-core: [138, 13056]
[   17.024942] mpp_rkvdec2 fdc48100.rkvdec-core: [142, 291584]
[   17.024988] mpp_rkvdec2 fdc48100.rkvdec-core: probing finish
[   17.025292] mpp_rkvenc2 rkvenc-ccu: probing start
[   17.025305] mpp_rkvenc2 rkvenc-ccu: probing finish
[   17.025469] mpp_rkvenc2 fdbd0000.rkvenc-core: Adding to iommu group 10
[   17.025694] mpp_rkvenc2 fdbd0000.rkvenc-core: probing start
[   17.025934] mpp_rkvenc2 fdbd0000.rkvenc-core: dev_pm_opp_set_regulators: no regulator (venc) found: -19
[   17.025968] rkvenc_init:1859: failed to add venc devfreq
[   17.026013] mpp_rkvenc2 fdbd0000.rkvenc-core: attach ccu as core 0
[   17.026231] mpp_rkvenc2 fdbd0000.rkvenc-core: probing finish
[   17.026344] mpp_rkvenc2 fdbe0000.rkvenc-core: Adding to iommu group 11
[   17.026571] mpp_rkvenc2 fdbe0000.rkvenc-core: probing start
[   17.026782] mpp_rkvenc2 fdbe0000.rkvenc-core: dev_pm_opp_set_regulators: no regulator (venc) found: -19
[   17.026811] rkvenc_init:1859: failed to add venc devfreq
[   17.026881] mpp_rkvenc2 fdbe0000.rkvenc-core: attach ccu as core 1
[   17.027117] mpp_rkvenc2 fdbe0000.rkvenc-core: probing finish
[   17.027910] mpp_av1dec: Adding child /av1d@fdc70000
[   17.028030] mpp_av1dec: register device av1d-master
[   17.028085] mpp_av1dec av1d-master: av1_iommu_of_xlate,784
[   17.028118] av1_iommu_probe_device,736, consumer : av1d-master, supplier : fdca0000.iommu
[   17.028176] mpp_av1dec av1d-master: Adding to iommu group 15
[   17.028485] mpp_av1dec av1d-master: probing start
[   17.028893] mpp_av1dec av1d-master: probing finish
[   17.028958] mpp_service mpp-srv: probe success
[   17.042720] dma-pl330 fea10000.dma-controller: Loaded driver for PL330 DMAC-241330
[   17.042739] dma-pl330 fea10000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[   17.043893] dma-pl330 fea30000.dma-controller: Loaded driver for PL330 DMAC-241330
[   17.043910] dma-pl330 fea30000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[   17.045017] dma-pl330 fed10000.dma-controller: Loaded driver for PL330 DMAC-241330
[   17.045034] dma-pl330 fed10000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[   17.045606] rockchip-pvtm fda40000.pvtm: pvtm@0 probed
[   17.045686] rockchip-pvtm fda50000.pvtm: pvtm@1 probed
[   17.045759] rockchip-pvtm fda60000.pvtm: pvtm@2 probed
[   17.045830] rockchip-pvtm fdaf0000.pvtm: pvtm@3 probed
[   17.045898] rockchip-pvtm fdb30000.pvtm: pvtm@4 probed
[   17.046626] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[   17.047596] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[   17.048143] febc0000.serial: ttyS9 at MMIO 0xfebc0000 (irq = 93, base_baud = 1500000) is a 16550A
[   17.209751] rk-pcie fe180000.pcie: PCIe Linking... LTSSM is 0x3
[   17.212040] printk: console [ttyS9] enabled
[   17.213588] random: crng init done
[   17.213679] led_vk2c21_init
[   17.213679] =============================================
[   17.214785] rockchip-vop2 fdd90000.vop: Adding to iommu group 14
[   17.223035] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[   17.224803] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 0
[   17.224811] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 1
[   17.224817] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 6
[   17.224823] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 7
[   17.224928] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] Esmart0-win0 as cursor plane for vp0
[   17.225033] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] Esmart1-win0 as cursor plane for vp1
[   17.225131] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] Esmart2-win0 as cursor plane for vp2
[   17.225223] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] Esmart3-win0 as cursor plane for vp3
[   17.225259] [drm] failed to init overlay plane Cluster0-win1
[   17.225261] [drm] failed to init overlay plane Cluster1-win1
[   17.225263] [drm] failed to init overlay plane Cluster2-win1
[   17.225264] [drm] failed to init overlay plane Cluster3-win1
[   17.237941] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffff8000093b3040)
[   17.241954] rk-pcie fe180000.pcie: PCIe Linking... LTSSM is 0x3
[   17.268586] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[   17.268614] rk-pcie fe180000.pcie: PCIe Linking... LTSSM is 0x3
[   17.278035] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[   17.295289] rk-pcie fe180000.pcie: PCIe Linking... LTSSM is 0x3
[   17.300362] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffff8000093c12c8)
[   17.311918] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[   17.322015] rockchip-drm display-subsystem: bound fde50000.dp (ops 0xffff8000093c3ed0)
[   17.331955] rk-pcie fe180000.pcie: PCIe Linking... LTSSM is 0x3
[   17.334518] rockchip-drm display-subsystem: failed to parse loader memory
[   17.351918] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[   17.365286] rk-pcie fe180000.pcie: PCIe Linking... LTSSM is 0x3
[   17.788586] dw-dp fde50000.dp: aux failed to read dpcd: -110
[   19.740101] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[   19.748063] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[   19.761084] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.2.auto: dw_hdcp_qp_hdcp_probe success
[   19.771581] brd: module loaded
[   19.775900] dw-dp fde50000.dp: aux failed to read dpcd: -110
[   19.778709] loop: module loaded
[   19.781601] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[   19.784980] rbd: loaded (major 254)
[   19.795675] lkdtm: No crash points registered, enable through debugfs
[   19.802343] system_heap: orders[0] = 6
[   19.806103] system_heap: orders[1] = 4
[   19.809854] system_heap: orders[2] = 0
[   19.816359] rockchip-spi feb20000.spi: no high_speed pinctrl state
[   19.820858] dw-dp fde50000.dp: aux failed to read dpcd: -110
[   19.824501] rk806 spi2.0: chip id: RK806,ver:0x2, 0x1
[   19.828233] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[   19.833449] rk806 spi2.0: ON: 0x40 OFF:0x0
[   19.847405] vdd_gpu_s0: supplied by vcc5v0_sys
[   19.853167] vdd_cpu_lit_s0: supplied by vcc5v0_sys
[   19.858910] vdd_log_s0: supplied by vcc5v0_sys
[   19.864217] vdd_vdenc_s0: supplied by vcc5v0_sys
[   19.869753] vdd_ddr_s0: supplied by vcc5v0_sys
[   19.874721] vdd2_ddr_s3: supplied by vcc5v0_sys
[   19.880019] vdd_2v0_pldo_s3: supplied by vcc5v0_sys
[   19.885600] vcc_3v3_s3: supplied by vcc5v0_sys
[   19.890688] vddq_ddr_s0: supplied by vcc5v0_sys
[   19.895987] vcc_1v8_s3: supplied by vcc5v0_sys
[   19.901237] vdd_0v75_s3: supplied by vcc_1v1_nldo_s3
[   19.906982] vdd_ddr_pll_s0: supplied by vcc_1v1_nldo_s3
[   19.912795] avdd_0v75_s0: Bringing 750000uV into 837500-837500uV
[   19.919043] avdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[   19.924770] vdd_0v85_s0: supplied by vcc_1v1_nldo_s3
[   19.930418] vdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[   19.936180] avcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[   19.942003] vcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[   19.947648] avdd_1v2_s0: supplied by vdd_2v0_pldo_s3
[   19.953372] vcc_3v3_s0: supplied by vcc5v0_sys
[   19.958501] vccio_sd_s0: supplied by vcc5v0_sys
[   19.958606] rk-pcie fe150000.pcie: PCIe Link Fail
[   19.967834] rk-pcie fe150000.pcie: failed to initialize host
[   19.974075] pldo6_s3: supplied by vcc5v0_sys
[   19.979025] rk806 spi2.0: no sleep-setting state
[   19.983661] rk806 spi2.0: no reset-setting pinctrl state
[   19.988977] rk806 spi2.0: no dvs-setting pinctrl state
[   19.995871] rockchip-spi feb20000.spi: register misc device rkspi-dev2
[   20.002408] rockchip-spi feb20000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[   20.012015] rk_gmac-dwmac fe1c0000.ethernet: IRQ eth_lpi not found
[   20.018405] rk_gmac-dwmac fe1c0000.ethernet: no regulator found
[   20.024337] rk_gmac-dwmac fe1c0000.ethernet: clock input or output? (output).
[   20.031475] rk_gmac-dwmac fe1c0000.ethernet: TX delay(0x43).
[   20.037143] rk_gmac-dwmac fe1c0000.ethernet: RX delay(0x0).
[   20.042732] rk_gmac-dwmac fe1c0000.ethernet: integrated PHY? (no).
[   20.048941] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_rx
[   20.055656] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_tx
[   20.062378] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock clk_mac_speed
[   20.069560] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID
[   20.075728] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[   20.082871] rk_gmac-dwmac fe1c0000.ethernet:         DWMAC4/5
[   20.088014] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported
[   20.095499] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported
[   20.102982] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported
[   20.110031] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported
[   20.116511] rk_gmac-dwmac fe1c0000.ethernet: TSO supported
[   20.122002] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[   20.130007] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2)
[   20.136710] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled
[   20.142722] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width
[   20.292242] usbcore: registered new interface driver rndis_wlan
[   20.298180]
[   20.299681] =======================================================
[   20.305948] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
[   20.312215] =======================================================
[   20.318482] Realtek 8821CS SDIO WiFi driver (Powered by Rockchip,Ver v5.14.2-28-g6011b0372.20220328) init.
[   20.328133] [WLAN_RFKILL]: rockchip_wifi_power: 1
[   20.328605] rk-pcie fe180000.pcie: PCIe Link Fail
[   20.332840] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
[   20.332843] RTW: module init start
[   20.332846] RTW: rtl8821cs v5.14.2-28-g6011b0372.20220328
[   20.332848] RTW: build time: Jan 29 2024 02:00:46
[   20.332850] RTW: rtl8821cs BT-Coex version = COEX20210319-5555
[   20.332891] RTW: module init ret=0
[   20.337597] rk-pcie fe180000.pcie: failed to initialize host
[   20.346476] usbcore: registered new interface driver asix
[   20.380314] usbcore: registered new interface driver cdc_ether
[   20.386170] usbcore: registered new interface driver rndis_host
[   20.392120] usbcore: registered new interface driver cdc_ncm
[   20.408703] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   20.415252] ehci-pci: EHCI PCI platform driver
[   20.419732] ehci-platform: EHCI generic platform driver
[   20.425214] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.431404] ohci-platform: OHCI generic platform driver
[   20.437108] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[   20.442619] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 1
[   20.450380] xhci-hcd xhci-hcd.7.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000202002010010
[   20.459803] xhci-hcd xhci-hcd.7.auto: irq 117, io mem 0xfc000000
[   20.466009] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[   20.474287] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   20.481513] usb usb1: Product: xHCI Host Controller
[   20.486395] usb usb1: Manufacturer: Linux 5.10.160-rockchip xhci-hcd
[   20.492749] usb usb1: SerialNumber: xhci-hcd.7.auto
[   20.497913] hub 1-0:1.0: USB hub found
[   20.501695] hub 1-0:1.0: 1 port detected
[   20.505816] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[   20.511319] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 2
[   20.518983] xhci-hcd xhci-hcd.7.auto: Host supports USB 3.0 SuperSpeed
[   20.525549] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[   20.533728] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[   20.542004] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   20.549229] usb usb2: Product: xHCI Host Controller
[   20.554110] usb usb2: Manufacturer: Linux 5.10.160-rockchip xhci-hcd
[   20.560465] usb usb2: SerialNumber: xhci-hcd.7.auto
[   20.565595] hub 2-0:1.0: USB hub found
[   20.569373] hub 2-0:1.0: 1 port detected
[   20.573590] phy phy-fd5d4000.syscon:usb2-phy@4000.1: illegal mode
[   20.579703] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[   20.585217] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[   20.592970] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000200002010010
[   20.602389] xhci-hcd xhci-hcd.8.auto: irq 118, io mem 0xfc400000
[   20.608587] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[   20.616856] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   20.624080] usb usb3: Product: xHCI Host Controller
[   20.628962] usb usb3: Manufacturer: Linux 5.10.160-rockchip xhci-hcd
[   20.635316] usb usb3: SerialNumber: xhci-hcd.8.auto
[   20.640442] hub 3-0:1.0: USB hub found
[   20.644225] hub 3-0:1.0: 1 port detected
[   20.648332] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[   20.653832] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[   20.661496] xhci-hcd xhci-hcd.8.auto: Host supports USB 3.0 SuperSpeed
[   20.668064] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[   20.676236] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[   20.684504] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   20.691728] usb usb4: Product: xHCI Host Controller
[   20.696609] usb usb4: Manufacturer: Linux 5.10.160-rockchip xhci-hcd
[   20.702964] usb usb4: SerialNumber: xhci-hcd.8.auto
[   20.708086] hub 4-0:1.0: USB hub found
[   20.711864] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[   20.719162] usbcore: registered new interface driver cdc_acm
[   20.724832] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   20.732994] usbcore: registered new interface driver uas
[   20.738363] usbcore: registered new interface driver usb-storage
[   20.745047] Error: Driver 'Goodix-TS' is already registered, aborting...
[   20.751791] usbcore: registered new interface driver usbtouchscreen
[   20.759273] input: rk805 pwrkey as /devices/platform/feb20000.spi/spi_master/spi2/spi2.0/rk805-pwrkey.5.auto/input/input0
[   20.770538] i2c /dev entries driver
[   20.777902] vdd_cpu_big0_s0: supplied by vcc5v0_sys
[   20.791599] vdd_cpu_big1_s0: supplied by vcc5v0_sys
[   20.805925] vdd_npu_s0: supplied by vcc5v0_sys
[   20.818980] rtc-hym8563 6-0051: rtc information is invalid
[   20.831391] rtc-hym8563 6-0051: registered as rtc0
[   20.837215] rtc-hym8563 6-0051: setting system clock to 2021-01-01T12:00:00 UTC (1609502400)
nberlee commented 4 months ago

This is a dmesg of another kernel, not a Talos one. Also the u-boot does have messages indicating its not running a ubiot build here. So flashing failed.

ned-si commented 4 months ago

Thanks a lot! I was mistakenly thinking that when the flashing process was successful, it meant that it was actually flashed properly. Thanks again for all your work to make Talos work on RK1!