Reaver frozen @ 44.9 %

[GoogleCodeExporter]

What steps will reproduce the problem?
1.
2.
3.

What is the expected output? What do you see instead?
continuing to go up in percentage till key is found

What version of the product are you using? On what operating system?
2.3

Please provide any additional information below.
Bt5 

Ran an attack and it incrimented to 44.9% and stopped there although it is 
active and not throwing errors. Can the % not changing mean that it has founf 
the first four and is working on the rest save the trailing checksum? 
Unfortunatly i did not run the -vv flag and dont want to restart the attack if 
i dont need to.. Great work so far!

Original issue reported on code.google.com by jeffmose...@gmail.com on 6 Jan 2012 at 12:38

[GoogleCodeExporter]

You put down that you are using version 2.3; I assume you meant 1.3? If you're 
using version 1.3 your session state will be auto-saved, so you can ctl+c to 
quit, and then re-start reaver against the same AP with the -vv flags. It will 
ask you if you want to restore the session; answer 'y' (no quotes) and it will 
pick up where it left off. 

Original comment by cheff...@tacnetsol.com on 6 Jan 2012 at 12:43

[GoogleCodeExporter]

Thank you for the fast reply. Now i am seeing the recieve timeout.
Going to give the ap some time and resume again. Perhaps i am locked
out of the ap

On Jan 5, 2012, at 7:44 PM, "reaver-wps@googlecode.com"
<reaver-wps@googlecode.com> wrote:

Original comment by jeffmose...@gmail.com on 6 Jan 2012 at 1:01

[GoogleCodeExporter]

Can you try walking over to the AP, power cycling it, and then resume reaver?

Original comment by peac...@tacnetsol.com on 6 Jan 2012 at 3:28

[GoogleCodeExporter]

No but i am doing some tests on the cisco i have here.. The light on
the router blinks when wps starts, getting it to blink is hit or miss
and if i miss the first pin i believe that calls for a reboot.
Although i am testing a power cycle too. The other attack is paused
till i figure out some order to things.

JeffMoses.com

On Jan 5, 2012, at 10:28 PM, "reaver-wps@googlecode.com"
<reaver-wps@googlecode.com> wrote:

Original comment by jeffmose...@gmail.com on 6 Jan 2012 at 3:34

[GoogleCodeExporter]

I have tried running mac changer pulling up and down mon -0 the ap i
have in house is just sitting not starting the wps cycle at all after
a reboot of both and a new mac.. No pulsing cisco...

JeffMoses.com

On Jan 5, 2012, at 10:28 PM, "reaver-wps@googlecode.com"
<reaver-wps@googlecode.com> wrote:

Original comment by jeffmose...@gmail.com on 6 Jan 2012 at 3:39

[GoogleCodeExporter]

jeff, can you provide pcaps please?

Original comment by cheff...@tacnetsol.com on 9 Jan 2012 at 6:51

• Added labels: Priority-Low
• Removed labels: Priority-Medium

[GoogleCodeExporter]

Working on that now... I think that this is actually a range issue..
Running two attacks now to confirm ... What is the pcap process?

JeffMoses.com

On Jan 9, 2012, at 1:51 PM, "reaver-wps@googlecode.com"
<reaver-wps@googlecode.com> wrote:

Original comment by jeffmose...@gmail.com on 9 Jan 2012 at 6:55

[GoogleCodeExporter]

Probably the easiest way is to use Wireshark. If your capture file is very 
large, you can use the display filter of 'eapol || eap' (no quotes), and save 
only the displayed packets to a file.

Original comment by cheff...@tacnetsol.com on 9 Jan 2012 at 6:57

[GoogleCodeExporter]

Thanks should be able to add it at some point today.

JeffMoses.com

On Jan 9, 2012, at 1:58 PM, "reaver-wps@googlecode.com"
<reaver-wps@googlecode.com> wrote:

Original comment by jeffmose...@gmail.com on 9 Jan 2012 at 7:01

[GoogleCodeExporter]

I am suspecting a network card issue.. I am running almost all
broadcom dell machines. I plan to pick up a new card tomorrow and
rerun some attacks. Do you think my logic is sound?

JeffMoses.com

On Jan 9, 2012, at 1:58 PM, "reaver-wps@googlecode.com"
<reaver-wps@googlecode.com> wrote:

Original comment by jeffmose...@gmail.com on 9 Jan 2012 at 11:19

[GoogleCodeExporter]

Well I'm not sure that it's a card issue since you were able to complete 45% of 
the attack, which means Reaver appears to be working with your existing card. 
Hard to tell without pcaps of what Reaver is actually sending and receiving 
though.

Original comment by cheff...@tacnetsol.com on 10 Jan 2012 at 1:46

[GoogleCodeExporter]

Original comment by cheff...@tacnetsol.com on 11 Jan 2012 at 5:03

• Changed state: NeedMoreInfo

[GoogleCodeExporter]

This is a problem running backtrack and a broadcom b43 chipset. I
picked up a usb alfa adaptor with a high gain antenna and have run 4
attacks at 1 second per attempt.. Fyi

JeffMoses.com

On Jan 11, 2012, at 12:03 PM, "reaver-wps@googlecode.com"
<reaver-wps@googlecode.com> wrote:

Original comment by jeffmose...@gmail.com on 12 Jan 2012 at 5:52

[GoogleCodeExporter]

Thanks for the info Jeff. I'll add the b43 chipset to the wiki.

Original comment by cheff...@tacnetsol.com on 17 Jan 2012 at 12:49

• Changed state: WontFix

[GoogleCodeExporter]

No problem. I had an idea for a feature, It would be nice to specify an
audible alarm for when a pin is found. Something in the line that could
point to a simple wav or midi file. perhaps a small alert could be included
with the reaver source?

Original comment by jeffmose...@gmail.com on 17 Jan 2012 at 1:25