It hangs out at Starting Kernel.....

[Drainer2002]

My rig was completely working fine for years already. today morning, I rebooted the rig and the light in-between the port turned on for couple of minutes and then turned off. every time I rebooted it , it did the same thing. I connected the rig to my computer and it hangs at starting kernel.....

Please help

`** PSH KERNEL VERSION: b0182929 WR: 20104000

---

SCU IPC: 0x800000d0 0xfffce92c

PSH miaHOB version: TNG.B0.VVBD.0000000c

microkernel built 10:14:01 Jan 13 2015

PSH loader PCM page cache size = 192 KB Cache Constraint = 0 Pages Arming IPC driver .. Adding page store pool .. PagestoreAddr(IMR Start Address) = 0x04899000 pageStoreSize(IMR Size) = 0x00080000

• Ready to receive application *

U-Boot 2014.04 (Feb 09 2015 - 15:40:31)

   Watchdog enabled

DRAM: 980.6 MiB MMC: tangier_sdhci: 0 In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 Target:blank Partitioning already done... Flashing already done... GADGET DRIVER: usb_dnl_dfu reading vmlinuz 4841888 bytes read in 155 ms (29.8 MiB/s) Valid Boot Flag Setup Size = 0x00003c00 Magic signature found Using boot protocol version 2.0c Linux kernel version 3.10.98-jubilinux-edison (robin@robin-i7) #13 SMP PREEMPT Fri Jun 23 02:24:12 EDT 2017 Building boot_params at 0x00090000 Loading bzImage at address 00100000 (4826528 bytes) Magic signature found Kernel command line: "rootwait root=PARTUUID=012b3303-34ac-284d-99b4-34e03a2335f4 rootfstype=ext4 console=ttyMFD2 earlyprintk=ttyMFD2,keep loglevel=4 g_multi.ethernet_config=rndis systemd.unit=multi-user.target hardware_id=00 g_multi.iSerialNumber=7beb42dc3a904d201d984157e4c3e600 g_multi.dev_addr=02:00:86:c3:e6:00"

Starting kernel ...`

[Drainer2002]

`arget:blank Partitioning already done... Flashing already done... GADGET DRIVER: usb_dnl_dfu reading vmlinuz 4841888 bytes read in 159 ms (29 MiB/s) Valid Boot Flag Setup Size = 0x00003c00 Magic signature found Using boot protocol version 2.0c Linux kernel version 3.10.98-jubilinux-edison (robin@robin-i7) #13 SMP PREEMPT Fri Jun 23 02:24:12 EDT 2017 Building boot_params at 0x00090000 Loading bzImage at address 00100000 (4826528 bytes) Magic signature found Kernel command line: "rootwait root=PARTUUID=012b3303-34ac-284d-99b4-34e03a2335f4 rootfstype=ext4 console=ttyMFD2 earlyprintk=ttyMFD2,keep loglevel=4 g_multi.ethernet_config=rndis systemd.unit=multi-user.target hardware_id=00 g_multi.iSerialNumber=7beb42dc3a904d201d984157e4c3e600 g_multi.dev_addr=02:00:86:c3:e6:00"

Starting kernel ...`

[scottleibrand]

The most likely cause for this kind of failure is Edison SSD degradation. You’ll probably need to reflash the rig, most likely multiple times until it manages to mark all the bad sectors and use other ones. And/or you can buy a fresh Edison off eBay and flash that.

[Drainer2002]

the thing is I am living in Russia currently, so it was okay to have it transported to me but now.... its hard.

How can I start reflashing, when I can't enter on it ? like what happened ?

[Drainer2002]

can I get your discord, to be able to contact bait easier, please?

[scottleibrand]

You should be able to reimage your current hardware by following the instructions at https://openaps.readthedocs.io/en/latest/docs/Resources/Edison-Flashing/all-computers-flash.html

[Drainer2002]

Could be outdated or highly loaded nightscout? Because when I checked the disk, it was 91% full.

[scottleibrand]

If the kernel won’t even boot, it wouldn’t have anything to do with Nightscout.

[Drainer2002]

It does reboot, when it hangs at starting kernel.....