search

openhab / org.openhab.binding.zwave

openHAB binding for Z-Wave
Eclipse Public License 2.0
170 stars 202 forks source link

Binding of Climax Z-Wave devices #1676

Closed lterziu closed 2 years ago

lterziu commented 2 years ago

The issue is that Climax Z-Wave devices can be enrolled in Raspberry Pi with connected RaZberry module, but there is no setting and control possible. On Raspberry is installed openHABian release 3.1.0 with the Adds "Z-Wave Serial Controller" and "Pigpio Remote".

cdjackson commented 2 years ago

I'm afraid I really don't know what this issue is about. I guess you have an issue with a specific device, but you don't say what the device is - I don't know what a "pigpio remote" is either. If this is an issue about a specific device, then you might need to add it to the database (see the documentation) otherwise I think you should discuss this on the support forum first as I doubt this is really about a bug in the binding.

lterziu commented 2 years ago

Dear Chris Jackson

Thank you for the email - sorry for the wrong information in the forum.

After enrolling CLIMAX Z-WAVE devices I get following information: This device has not been fully discovered by the binding. There are a few possible reasons for this -: The device is not in the database. If the device attributes show that this device has a valid manufacturer ID, device ID and type, then this is likely the case (eg. you see a label like "Z-Wave node 1 (0082:6015:020D::2.0)"). Even if the device appears to be in the database, some manufacturers use multiple sets of references for different regions or versions, and your device references may not be in the database. In either case, the database must be updated and you should raise an issue to get this addressed. The device initialisation is not complete. Once the device is included into the network, the binding must interrogate it to find out what type of device it is. One part of this process is to get the manufacturer information required to identify the device, and until this is done, the device will remain unknown. For mains powered devices, this will occur quickly, however for battery devices the device must be woken up a number of times to allow the discovery phase to complete. This must be performed with the device close to the controller.

Maybe you have any idea how to proceed?

Sorry for missunderstanding...

Kind regards, Luciano Terziu

Von: Chris Jackson @.> Gesendet: Dienstag, 26. Oktober 2021 21:05 An: openhab/org.openhab.binding.zwave @.> Cc: lterziu @.>; Author @.> Betreff: Re: [openhab/org.openhab.binding.zwave] Binding of Climax Z-Wave devices (Issue #1676)

I'm afraid I really don't know what this issue is about. I guess you have an issue with a specific device, but you don't say what the device is - I don't know what a "pigpio remote" is either. If this is an issue about a specific device, then you might need to add it to the database (see the documentation) otherwise I think you should discuss this on the support forum first as I doubt this is really about a bug in the binding.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHubhttps://github.com/openhab/org.openhab.binding.zwave/issues/1676#issuecomment-952227756, or unsubscribehttps://github.com/notifications/unsubscribe-auth/AWHGJ6CUOIJNLQOAASVW2RLUI4CXHANCNFSM5GYM7KDA. Triage notifications on the go with GitHub Mobile for iOShttps://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675 or Androidhttps://play.google.com/store/apps/details?id=com.github.android&referrer=utm_campaign%3Dnotification-email%26utm_medium%3Demail%26utm_source%3Dgithub.

cdjackson commented 2 years ago

It looks like this device is not in the database so it will need to be added. You can find the database guide below - I'd suggest to discuss on the support forum if you need any help.

https://opensmarthouse.org/blog/zwave_device_database_guide