MGV2000有线网口无法使用

SOC: [S905L2]
Armbian Version | 23.02.0
Kernel Version: [5.15.95]
Release: [jammy]
Describe the bug | 问题描述 MGV2000，可以启动，可以刷入EMMC，有线网口无法使用尝试过5.15.91和5.15.95，DTB试过meson-gxl-s905l2-x7-5g.dtb、meson-gxl-s905l2-ipbs9505.dtb、meson-gxl-s905x-p212.dtb、meson-gxl-s905l3b-e900v22e.dtb
附启动信息：

GXLX:BL1:9ac50e:4a8da0;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 157683

BL2 Built : 14:48:45, Sep 26 2018.
gxl g6d68897 - yao.zhang@droid07

Board ID = 3, adc=226
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
DDR3
DDR3 chl: Rank0 @ 792MHz

bist_test rank: 0 25 0c 3e 35 1a 50 1f 04 3a 36 1b 52 1d 06 35 34 19 4f 25 0b 3f 34 16 52 709
Rank0: 1024MB(auto)-2T-11
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00047200
NOTICE:  BL3-1: v1.0(debug):521e8c3
NOTICE:  BL3-1: Built : 14:22:49, Jun  5 2018
NOTICE:  BL31: GXL normal boot!
NOTICE:  BL31: BL33 decompress pass
[Image: gxl_v1.1.3101-a78fa1e 2018-06-04 16:24:21 huan.biao@droid12]
efuse init ops = c1
efuse init hdcp = c, cf9=7
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 ae b3 50 a0 0 c1 not ES chip
[0.573726 Inits done]
INFO:    BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01-g04eb360-dirty (Nov 04 2019 - 10:18:39)

DRAM:  1 GiB
Relocation Offset is: 36eef000
gpio: pin GPIODV_24 (gpio 43) value is 1
register usb cfg[0][1] = 0000000037f61688
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC:   aml_priv->desc_buf = 0x0000000033edfac0
aml_priv->desc_buf = 0x0000000033ee1de0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
dtb magic 08088b1f
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      2layers board, board id use 7
      Multi dtb tool version: v2 .
      Support 8 dtbs.
        aml_dt soc: gxlx platform: p261 variant: 1g
        dtb 0 soc: gxl   plat: p211   vari: 1g
        dtb 1 soc: gxl   plat: p215   vari: 1g
        dtb 2 soc: gxlx   plat: p261   vari: 1g
        dtb 3 soc: gxlx   plat: p261   vari: 2g
        dtb 4 soc: gxlx   plat: p265   vari: 1g
        dtb 5 soc: gxlx   plat: p265   vari: 2g
        dtb 6 soc: gxlx2   plat: p291   vari: 1g
        dtb 7 soc: gxlx2   plat: p295   vari: 1g
      Find match dtb: 2
start dts,buffer=0000000033ee4610,dt_addr=0000000033ee4610
      Amlogic multi-dtb tool
      Single dtb detected
parts: 16
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06: instaboot   0000000020000000 1
07:      boot   0000000002000000 1
08:    system   0000000040000000 1
09:     cache   0000000020000000 2
10:    params   0000000004000000 2
11:       ctc   0000000012c00000 2
12: bootfiles   0000000020000000 2
13:   private   0000000000800000 2
14: flashdata   0000000004000000 2
15:      data   ffffffffffffffff 4
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
board id is : 3
hpd_state=0
cvbs performance type = 7, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-924: calc fd802a71, store fd802a71
_verify_dtb_checksum()-924: calc fd802a71, store fd802a71
dtb_read()-1046: total valid 2
dtb_read()-1113: do nothing
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      2layers board, board id use 7
      Multi dtb tool version: v2 .
      Support 8 dtbs.
        aml_dt soc: gxlx platform: p261 variant: 1g
        dtb 0 soc: gxl   plat: p211   vari: 1g
        dtb 1 soc: gxl   plat: p215   vari: 1g
        dtb 2 soc: gxlx   plat: p261   vari: 1g
        dtb 3 soc: gxlx   plat: p261   vari: 2g
        dtb 4 soc: gxlx   plat: p265   vari: 1g
        dtb 5 soc: gxlx   plat: p265   vari: 2g
        dtb 6 soc: gxlx2   plat: p291   vari: 1g
        dtb 7 soc: gxlx2   plat: p295   vari: 1g
      Find match dtb: 2
wipe_data=successful
wipe_cache=successful
bmp pixel: 24
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[CANVAS]addr=0x3dc00000 width=5760, height=2160
upgrade_step=2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[hw] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[model] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[factoryinfo] not programed yet
key1 = 7d82dd22
key2 = 7e81dd22
key3 = 728ddd22
time_out = 7a120
ir init
P_AO_IR_DEC_REG0:70fa0013, P_AO_IR_DEC_REG1:3e70
time_base = 15bd63
out----irkey - irkey key_value1 key_value2 key_value3 time_value

Usage:
irkey
rebootmode=cold_boot
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... init_part() 278: PART_TYPE_DOS
1 Storage Device(s) found
reading s905_autoscript
1654 bytes read in 52 ms (30.3 KiB/s)
## Executing script at 01020000
start amlogic old u-boot
## Error: "bootfromsd" not defined
card out
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
emmc/sd response timeout, cmd1, status=0x1ff2800
** Bad device mmc 0 **
reading boot_android
** Unable to read file boot_android **
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
emmc/sd response timeout, cmd1, status=0x1ff2800
** Bad device mmc 0 **
reading u-boot.ext
** Unable to read file u-boot.ext **
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
emmc/sd response timeout, cmd1, status=0x1ff2800
** Bad device mmc 0 **
start test usb
reading uEnv.txt
359 bytes read in 42 ms (7.8 KiB/s)
mac=74:8F:1B:26:9A:8F
reading /zImage
25469440 bytes read in 13513 ms (1.8 MiB/s)
reading /uInitrd
8239191 bytes read in 4462 ms (1.8 MiB/s)
reading /dtb/amlogic/meson-gxl-s905l2-x7-5g.dtb
39577 bytes read in 233 ms (165 KiB/s)
## Error: "aadmac" not defined
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] bl31 reserved memory set addr error.
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    8239127 Bytes = 7.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
      Amlogic multi-dtb tool
      Single dtb detected
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
   Booting using the fdt blob at 0x1000000
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] bl31 reserved memory set addr error.
   Loading Ramdisk to 33701000, end 33edc817 ... OK
   Loading Device Tree to 000000000fff3000, end 000000000ffffa98 ... OK
signature:
fdt_instaboot: get header err

Starting kernel ...

uboot time: 23901725 us
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.15.95-flippy-82+o (root@univm25) (Ubuntu clang version 14.0.0-1ubuntu1, Ubuntu LLD 14.0.0) #212 SMP PREEMPT Thu Feb 23 21:20:57 CST 2023
[    0.000000] Machine model: Amlogic Meson GXL (S905L2) X7 5G Tv Box
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000023400000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x0000000037ffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000000ffffff]
[    0.000000]   node   0: [mem 0x0000000001000000-0x0000000004ffffff]
[    0.000000]   node   0: [mem 0x0000000005000000-0x00000000072fffff]
[    0.000000]   node   0: [mem 0x0000000007300000-0x000000000fffffff]
[    0.000000]   node   0: [mem 0x0000000010000000-0x00000000101fffff]
[    0.000000]   node   0: [mem 0x0000000010200000-0x0000000037ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000037ffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] percpu: Embedded 19 pages/cpu s37720 r8192 d31912 u77824
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 225792
[    0.000000] Kernel command line: root=UUID=f3a25d56-1b8f-440f-8796-466a33315fa4 rootflags=data=writeback rw rootfstype=ext4 console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 mac=74:8F:1B:26:9A:8F
[    0.000000] Unknown kernel command line parameters "cgroup_enable=memory cgroup_memory=1 mac=74:8F:1B:26:9A:8F", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 550772K/917504K available (15296K kernel code, 2728K rwdata, 4716K rodata, 1984K init, 887K bss, 104588K reserved, 262144K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] irq_meson_gpio: 110 to 8 gpio interrupt mux initialized
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000572] Console: colour dummy device 80x25
[    0.000992] printk: console [tty0] enabled
[    0.001051] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.001077] pid_max: default: 32768 minimum: 301
[    0.001277] LSM: Security Framework initializing
[    0.001386] SELinux:  Initializing.
[    0.001643] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.001667] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.003911] rcu: Hierarchical SRCU implementation.
[    0.005090] EFI services will not be available.
[    0.005568] smp: Bringing up secondary CPUs ...
[    0.006233] Detected VIPT I-cache on CPU1
[    0.006309] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.007085] Detected VIPT I-cache on CPU2
[    0.007147] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.007854] Detected VIPT I-cache on CPU3
[    0.007909] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.007994] smp: Brought up 1 node, 4 CPUs
[    0.008068] SMP: Total of 4 processors activated.
[    0.008080] CPU features: detected: 32-bit EL0 Support
[    0.008091] CPU features: detected: 32-bit EL1 Support
[    0.008103] CPU features: detected: CRC32 instructions
[    0.008931] CPU: All CPU(s) started at EL2
[    0.008964] alternatives: patching kernel code
[    0.010682] devtmpfs: initialized
[    0.019011] Registered cp15_barrier emulation handler
[    0.019053] Registered setend emulation handler
[    0.019214] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.019246] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.025887] prandom: seed boundary self test passed
[    0.027113] prandom: 100 self tests passed
[    0.050056] prandom32: self test passed (less than 6 bits correlated)
[    0.050111] pinctrl core: initialized pinctrl subsystem
[    0.050749] DMI not present or invalid.
[    0.051243] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.053252] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.053426] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.053622] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.053721] audit: initializing netlink subsys (disabled)
[    0.053975] audit: type=2000 audit(0.053:1): state=initialized audit_enabled=0 res=1
[    0.055070] thermal_sys: Registered thermal governor 'step_wise'
[    0.055401] cpuidle: using governor ladder
[    0.055588] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.055714] ASID allocator initialised with 65536 entries
[    0.055893] Serial: AMBA PL011 UART driver
[    0.074991] platform c883a000.hdmi-tx: Fixing up cyclic dependency with d0100000.vpu
[    0.079647] platform cvbs-connector: Fixing up cyclic dependency with d0100000.vpu
[    0.079951] platform hdmi-connector: Fixing up cyclic dependency with c883a000.hdmi-tx
[    0.088786] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.088823] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.088837] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.088851] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    1.498939] cryptd: max_cpu_qlen set to 1000
[    1.502820] "cryptomgr_test" (91) uses obsolete ecb(arc4) skcipher
[    1.515170] alg: No test for 842 (842-generic)
[    1.515315] alg: No test for 842 (842-scomp)
[    1.606122] DRBG: Continuing without Jitter RNG
[    1.689743] raid6: neonx8   gen()  2226 MB/s
[    1.746491] raid6: neonx8   xor()  1604 MB/s
[    1.803256] raid6: neonx4   gen()  2210 MB/s
[    1.860003] raid6: neonx4   xor()  1537 MB/s
[    1.916769] raid6: neonx2   gen()  2038 MB/s
[    1.973524] raid6: neonx2   xor()  1435 MB/s
[    2.030290] raid6: neonx1   gen()  1665 MB/s
[    2.087040] raid6: neonx1   xor()  1178 MB/s
[    2.143805] raid6: int64x8  gen()  1558 MB/s
[    2.200545] raid6: int64x8  xor()   813 MB/s
[    2.257311] raid6: int64x4  gen()  1668 MB/s
[    2.314057] raid6: int64x4  xor()   839 MB/s
[    2.370830] raid6: int64x2  gen()  1477 MB/s
[    2.427603] raid6: int64x2  xor()   771 MB/s
[    2.484322] raid6: int64x1  gen()  1120 MB/s
[    2.541051] raid6: int64x1  xor()   583 MB/s
[    2.541064] raid6: using algorithm neonx8 gen() 2226 MB/s
[    2.541076] raid6: .... xor() 1604 MB/s, rmw enabled
[    2.541087] raid6: using neon recovery algorithm
[    2.541318] fbcon: Taking over console
[    2.541359] ACPI: Interpreter disabled.
[    2.543641] iommu: Default domain type: Translated
[    2.543675] iommu: DMA domain TLB invalidation policy: strict mode
[    2.544032] vgaarb: loaded
[    2.544582] SCSI subsystem initialized
[    2.544812] usbcore: registered new interface driver usbfs
[    2.544862] usbcore: registered new interface driver hub
[    2.544907] usbcore: registered new device driver usb
[    2.545432] mc: Linux media interface: v0.10
[    2.545467] videodev: Linux video capture interface: v2.00
[    2.545733] EDAC MC: Ver: 3.0.0
[    2.546911] Advanced Linux Sound Architecture Driver Initialized.
[    2.548030] clocksource: Switched to clocksource arch_sys_counter
[    2.548368] VFS: Disk quotas dquot_6.6.0
[    2.548460] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    2.548634] FS-Cache: Loaded
[    2.549160] pnp: PnP ACPI: disabled
[    2.556517] NET: Registered PF_INET protocol family
[    2.556692] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    2.557600] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    2.557645] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    2.557669] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    2.557807] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    2.557940] TCP: Hash tables configured (established 8192 bind 8192)
[    2.558227] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, linear)
[    2.558317] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    2.558355] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    2.558533] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    2.558573] NET: Registered PF_XDP protocol family
[    2.558595] PCI: CLS 0 bytes, default 64
[    2.558935] Trying to unpack rootfs image as initramfs...
[    2.568767] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    2.569298] kvm [1]: IPA Size Limit: 40 bits
[    2.570156] kvm [1]: vgic interrupt IRQ9
[    2.570319] kvm [1]: Hyp mode initialized successfully
[    3.158427] Freeing initrd memory: 8044K
[    3.383600] Initialise system trusted keyrings
[    3.383891] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    3.391305] zbud: loaded
[    3.393152] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    3.393763] fuse: init (API version 7.34)
[    3.394289] SGI XFS with ACLs, security attributes, quota, no debug enabled
[    3.435727] NET: Registered PF_ALG protocol family
[    3.486325] xor: measuring software checksum speed
[    3.491161]    8regs           :  2051 MB/sec
[    3.494566]    32regs          :  2908 MB/sec
[    3.499159]    arm64_neon      :  2153 MB/sec
[    3.499172] xor: using function: 32regs (2908 MB/sec)
[    3.499188] Key type asymmetric registered
[    3.499200] Asymmetric key parser 'x509' registered
[    3.499313] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    3.499507] io scheduler mq-deadline registered
[    3.499522] io scheduler kyber registered
[    3.499718] io scheduler bfq registered
[    3.526726] soc soc0: Amlogic Meson GXLX (Unknown) Revision 26:e (c1:2) Detected
[    3.529284] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[    3.531471] Serial: AMBA driver
[    3.531910] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 22, base_baud = 1500000) is a meson_uart
[    4.554576] printk: console [ttyAML0] enabled
[    4.569209] brd: module loaded
[    4.573924] loop: module loaded
[    4.581281] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.582216] ehci-pci: EHCI PCI platform driver
[    4.586674] ehci-platform: EHCI generic platform driver
[    4.592417] usbcore: registered new interface driver cdc_wdm
[    4.597422] usbcore: registered new interface driver usb-storage
[    4.603933] mousedev: PS/2 mouse device common for all mice
[    4.610075] SPI driver rmi4_spi has no spi_device_id for syna,rmi4-spi
[    4.616228] meson-vrtc c81000a8.rtc: registered as rtc0
[    4.620514] meson-vrtc c81000a8.rtc: setting system clock to 1970-01-01T00:00:04 UTC (4)
[    4.629084] i2c_dev: i2c /dev entries driver
[    4.635086] Registered IR keymap rc-cec
[    4.636681] rc rc0: meson_ao_cec as /devices/platform/soc/c8100000.bus/c8100100.cec/rc/rc0
[    4.644898] input: meson_ao_cec as /devices/platform/soc/c8100000.bus/c8100100.cec/rc/rc0/input0
[    4.657246] sdhci: Secure Digital Host Controller Interface driver
[    4.659579] sdhci: Copyright(c) Pierre Ossman
[    4.663869] Synopsys Designware Multimedia Card Interface Driver
[    4.670879] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.671394] meson-gx-mmc d0072000.mmc: Got CD GPIO
[    4.672517] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq
[    4.678600] meson-sm: secure-monitor enabled
[    4.692448] gxl-crypto c883e000.crypto: will run requests pump with realtime priority
[    4.697836] gxl-crypto c883e000.crypto: will run requests pump with realtime priority
[    4.709383] hid: raw HID events driver (C) Jiri Kosina
[    4.710684] usbcore: registered new interface driver usbhid
[    4.714192] gpio irq setup: hwirq: 0x3A irqfirst: 0x34 irqlast: 0x3A pin[48]
[    4.716197] usbhid: USB HID core driver
[    4.723372] genirq: Setting trigger mode 3 for irq 46 failed (meson_gpio_irq_set_type+0x0/0x140)
[    4.727472] platform-mhu c883c404.mailbox: Platform MHU Mailbox registered
[BL31]: tee size: 0
[    4.750893] Initializing XFRM netlink socket
[    4.751607] NET: Registered PF_INET6 protocol family
[    4.792221] Segment Routing with IPv6
[    4.792268] RPL Segment Routing with IPv6
[    4.794297] In-situ OAM (IOAM) with IPv6
[    4.798427] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    4.807386] bpfilter: Loaded bpfilter_umh pid 302
[    4.808740] NET: Registered PF_PACKET protocol family
[    4.813801] NET: Registered PF_KEY protocol family
[    4.818595] 8021q: 802.1Q VLAN Support v1.8
[    4.823070] registered taskstats version 1
[    4.826761] Loading compiled-in X.509 certificates
[    4.834050] zswap: loaded using pool zstd/zbud
[    4.836499] Key type .fscrypt registered
[    4.839643] Key type fscrypt-provisioning registered
[    4.845687] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no
[    4.876678] mmc2: mmc_select_hs200 failed, error -74
[    4.878226] mmc2: new MMC card at address 0001
[    4.881334] mmcblk2: mmc2:0001 DG4008 7.28 GiB
[    4.885326] meson-drm d0100000.vpu: Queued 3 outputs on vpu
[    4.888396] mmcblk2boot0: mmc2:0001 DG4008 4.00 MiB
[    4.897008] mmcblk2boot1: mmc2:0001 DG4008 4.00 MiB
[    4.901603] mmcblk2rpmb: mmc2:0001 DG4008 4.00 MiB, chardev (240:0)
[    4.918148] meson-dw-hdmi c883a000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
[    4.922966] meson-dw-hdmi c883a000.hdmi-tx: registered DesignWare HDMI I2C bus driver
[    4.930935] meson-drm d0100000.vpu: bound c883a000.hdmi-tx (ops 0xffffffc00a2fa8d8)
[    4.938541] [drm] Initialized meson 1.0.0 20161109 for d0100000.vpu on minor 0
[    4.949114] Console: switching to colour frame buffer device 90x36
[    4.974300] meson-drm d0100000.vpu: [drm] fb0: mesondrmfb frame buffer device
[    4.983677] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found
[    4.987952] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found
[    4.994402] meson8b-dwmac c9410000.ethernet: PTP uses main clock
[    5.001092] meson8b-dwmac c9410000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[    5.007103] meson8b-dwmac c9410000.ethernet:         DWMAC1000
[    5.012269] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported
[    5.019670] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported
[    5.027087] meson8b-dwmac c9410000.ethernet: COE Type 2
[    5.032265] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported
[    5.039249] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported
[    5.045635] meson8b-dwmac c9410000.ethernet: Normal descriptors
[    5.051501] meson8b-dwmac c9410000.ethernet: Ring mode enabled
[    5.057275] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    5.065221] meson8b-dwmac c9410000.ethernet: device MAC address 12:e3:c4:60:67:65
[    5.075945] dwc3-meson-g12a d0078080.usb: USB2 ports: 2
[    5.078559] dwc3-meson-g12a d0078080.usb: USB3 ports: 0
[    5.602695] dwc2 c9100000.usb: supply vusb_d not found, using dummy regulator
[    5.607021] dwc2 c9100000.usb: supply vusb_a not found, using dummy regulator
[    5.614158] dwc2 c9100000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[    5.623195] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.626548] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 1
[    5.634007] xhci-hcd xhci-hcd.3.auto: hcc params 0x0228f664 hci version 0x100 quirks 0x0000000002010010
[    5.643237] xhci-hcd xhci-hcd.3.auto: irq 48, io mem 0xc9000000
[    5.649262] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.654668] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 2
[    5.662066] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed
[    5.668687] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[    5.676714] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.683872] usb usb1: Product: xHCI Host Controller
[    5.688701] usb usb1: Manufacturer: Linux 5.15.95-flippy-82+o xhci-hcd
[    5.695170] usb usb1: SerialNumber: xhci-hcd.3.auto
[    5.700639] hub 1-0:1.0: USB hub found
[    5.703768] hub 1-0:1.0: 2 ports detected
[    5.708187] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.715825] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15
[    5.723894] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.731146] usb usb2: Product: xHCI Host Controller
[    5.735886] usb usb2: Manufacturer: Linux 5.15.95-flippy-82+o xhci-hcd
[    5.742349] usb usb2: SerialNumber: xhci-hcd.3.auto
[    5.747748] hub 2-0:1.0: USB hub found
[    5.750953] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    5.762163] meson-gx-mmc d0070000.mmc: allocated mmc-pwrseq
[    5.762633] scpi_protocol scpi: SCP Protocol legacy pre-1.0 firmware
get_dvfs_info 0007
[    5.801935] ALSA device list:
[    5.805038]   No soundcards found.
[    5.808854] Freeing unused kernel memory: 1984K
[    5.824774] Run /init as init process
[    5.954737] usb 1-2: new high-speed USB device number 2 using xhci-hcd
[    6.104733] usb 1-2: New USB device found, idVendor=05e3, idProduct=0749, bcdDevice=15.32
[    6.113045] usb 1-2: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    6.120097] usb 1-2: Product: USB3.0 Card Reader
[    6.124668] usb 1-2: Manufacturer: Generic
[    6.128762] usb 1-2: SerialNumber: 000000001532
[    6.135878] usb-storage 1-2:1.0: USB Mass Storage device detected
[    6.141475] scsi host0: usb-storage 1-2:1.0
[    7.150244] scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   1532 PQ: 0 ANSI: 6
[    7.451637] sd 0:0:0:0: [sda] 15523840 512-byte logical blocks: (7.95 GB/7.40 GiB)
[    7.461806] sd 0:0:0:0: [sda] Write Protect is off
[    7.476773] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    7.499080]  sda: sda1 sda2
[    7.507748] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    7.996646] EXT4-fs (sda2): recovery complete
[    8.000924] EXT4-fs (sda2): mounted filesystem with writeback data mode. Opts: data=writeback. Quota mode: none.
[    8.483668] systemd[1]: System time before build time, advancing clock.
[    8.594887] systemd[1]: systemd 249.11-0ubuntu3.6 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    8.647296] systemd[1]: Detected architecture arm64.
[    8.665192] systemd[1]: Hostname set to <armbian>.
[    9.600605] systemd[1]: Queued start job for default target Graphical Interface.
[    9.607356] random: systemd: uninitialized urandom read (16 bytes read)
[    9.616410] systemd[1]: Created slice Slice /system/modprobe.
[    9.623386] random: systemd: uninitialized urandom read (16 bytes read)
[    9.629723] systemd[1]: Created slice Slice /system/serial-getty.
[    9.637059] random: systemd: uninitialized urandom read (16 bytes read)
[    9.643714] systemd[1]: Created slice Slice /system/systemd-fsck.
[    9.652306] systemd[1]: Created slice User and Session Slice.
[    9.659542] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    9.669293] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    9.683819] systemd[1]: Reached target Slice Units.
[    9.690980] systemd[1]: Reached target Swaps.
[    9.698126] systemd[1]: Reached target System Time Set.
[    9.705242] systemd[1]: Reached target Local Verity Protected Volumes.
[    9.733778] systemd[1]: Listening on RPCbind Server Activation Socket.
[    9.743712] systemd[1]: Listening on Syslog Socket.
[    9.751734] systemd[1]: Listening on fsck to fsckd communication Socket.
[    9.760312] systemd[1]: Listening on initctl Compatibility Named Pipe.
[    9.769627] systemd[1]: Listening on Journal Audit Socket.
[    9.777734] systemd[1]: Listening on Journal Socket (/dev/log).
[    9.786301] systemd[1]: Listening on Journal Socket.
[    9.794015] systemd[1]: systemd-networkd.socket: Socket service systemd-networkd.service not loaded, refusing.
[    9.805170] systemd[1]: Failed to listen on Network Service Netlink Socket.
[    9.821459] systemd[1]: Listening on udev Control Socket.
[    9.829525] systemd[1]: Listening on udev Kernel Socket.
[    9.841423] systemd[1]: Mounting Huge Pages File System...
[    9.853263] systemd[1]: Mounting POSIX Message Queue File System...
[    9.865616] systemd[1]: Mounting Kernel Debug File System...
[    9.873147] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[    9.883074] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[    9.900266] systemd[1]: Starting Restore / save the current clock...
[    9.913671] systemd[1]: Starting Wait for network to be configured by ifupdown...
[    9.928379] systemd[1]: Starting Set the console keyboard layout...
[    9.942442] systemd[1]: Starting Create List of Static Device Nodes...
[    9.957411] systemd[1]: Starting Load Kernel Module chromeos_pstore...
[    9.972181] systemd[1]: Starting Load Kernel Module configfs...
[    9.985865] systemd[1]: Starting Load Kernel Module drm...
[    9.999084] systemd[1]: Starting Load Kernel Module efi_pstore...
[   10.012636] systemd[1]: Starting Load Kernel Module fuse...
[   10.025700] systemd[1]: Starting Load Kernel Module pstore_blk...
[   10.038888] systemd[1]: Starting Load Kernel Module pstore_zone...
[   10.052193] systemd[1]: Starting Load Kernel Module ramoops...
[   10.066006] systemd[1]: Started Nameserver information manager.
[   10.074673] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   10.092760] systemd[1]: Starting Load Kernel Modules...
[   10.105536] systemd[1]: Starting Generate network units from Kernel command line...
[   10.120695] systemd[1]: Starting Remount Root and Kernel File Systems...
[   10.134802] systemd[1]: Starting Coldplug All udev Devices...
[   10.151554] EXT4-fs (sda2): re-mounted. Opts: discard,errors=remount-ro. Quota mode: none.
[   10.154082] systemd[1]: Mounted Huge Pages File System.
[   10.174377] systemd[1]: Mounted POSIX Message Queue File System.
[   10.182843] systemd[1]: Mounted Kernel Debug File System.
[   10.192091] systemd[1]: Finished Restore / save the current clock.
[   10.202063] systemd[1]: Finished Create List of Static Device Nodes.
[   10.211804] systemd[1]: modprobe@chromeos_pstore.service: Deactivated successfully.
[   10.219502] systemd[1]: Finished Load Kernel Module chromeos_pstore.
[   10.230465] systemd[1]: Finished Set the console keyboard layout.
[   10.240064] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[   10.247070] systemd[1]: Finished Load Kernel Module configfs.
[   10.256621] systemd[1]: modprobe@drm.service: Deactivated successfully.
[   10.262917] systemd[1]: Finished Load Kernel Module drm.
[   10.272409] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[   10.279390] systemd[1]: Finished Load Kernel Module efi_pstore.
[   10.289310] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[   10.295604] systemd[1]: Finished Load Kernel Module fuse.
[   10.305093] systemd[1]: modprobe@pstore_blk.service: Deactivated successfully.
[   10.312017] systemd[1]: Finished Load Kernel Module pstore_blk.
[   10.322207] systemd[1]: modprobe@pstore_zone.service: Deactivated successfully.
[   10.328987] systemd[1]: Finished Load Kernel Module pstore_zone.
[   10.339272] systemd[1]: modprobe@ramoops.service: Deactivated successfully.
[   10.345708] systemd[1]: Finished Load Kernel Module ramoops.
[   10.357703] systemd[1]: Finished Load Kernel Modules.
[   10.366843] systemd[1]: Finished Generate network units from Kernel command line.
[   10.378677] systemd[1]: Finished Remount Root and Kernel File Systems.
[   10.403983] systemd[1]: Reached target Preparation for Network.
[   10.416184] systemd[1]: Mounting FUSE Control File System...
[   10.428391] systemd[1]: Mounting Kernel Configuration File System...
[   10.436704] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   10.452422] systemd[1]: Starting Load/Save Random Seed...
[   10.465016] systemd[1]: Starting Apply Kernel Variables...
[   10.478345] systemd[1]: Starting Create System Users...
[   10.493395] systemd[1]: Mounted FUSE Control File System.
[   10.501625] systemd[1]: Mounted Kernel Configuration File System.
[   10.563188] systemd[1]: Finished Create System Users.
[   10.576000] systemd[1]: Starting Create Static Device Nodes in /dev...
[   10.586762] systemd[1]: Finished Apply Kernel Variables.
[   10.627310] systemd[1]: Finished Create Static Device Nodes in /dev.
[   10.635838] random: systemd: uninitialized urandom read (16 bytes read)
[   10.640455] systemd[1]: Reached target Preparation for Local File Systems.
[   10.650831] random: systemd: uninitialized urandom read (16 bytes read)
[   10.661174] systemd[1]: Mounting /tmp...
[   10.668520] random: systemd: uninitialized urandom read (16 bytes read)
[   10.680588] systemd[1]: Starting Rule-based Manager for Device Events and Files...
[   10.695365] systemd[1]: Finished Coldplug All udev Devices.
[   10.703698] systemd[1]: Mounted /tmp.
[   10.716920] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
[   10.889554] systemd[1]: Started Rule-based Manager for Device Events and Files.
[   10.905763] systemd[1]: Condition check resulted in Show Plymouth Boot Screen being skipped.
[   10.915370] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   10.929785] systemd[1]: Condition check resulted in Forward Password Requests to Plymouth Directory Watch being skipped.
[   10.942111] systemd[1]: Reached target Local Encrypted Volumes.
[   11.108068] random: crng init done
[   11.111563] random: 47 urandom warning(s) missed due to ratelimiting
[   11.154196] systemd[1]: Finished Load/Save Random Seed.
[   11.163096] systemd[1]: Condition check resulted in First Boot Complete being skipped.
[   11.335921] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[   11.356470] systemd[1]: Found device /dev/ttyAML0.
[   11.370384] Registered IR keymap rc-empty
[   11.374217] rc rc1: meson-ir as /devices/platform/soc/c8100000.bus/c8100580.ir/rc/rc1
[   11.380373] rc rc1: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter
[   11.391161] input: meson-ir as /devices/platform/soc/c8100000.bus/c8100580.ir/rc/rc1/input1
[   11.401526] meson-ir c8100580.ir: receiver initialized
[   11.420044] systemd[1]: Reached target Hardware activated USB gadget.
[   11.442174] debugfs: Directory 'c1105400.audio-controller' with parent 'P230-Q200' already present!
[   11.452745] debugfs: Directory 'c1105400.audio-controller' with parent 'P230-Q200' already present!
[   11.470317] lima d00c0000.gpu: gp - mali450 version major 0 minor 0
[   11.475325] lima d00c0000.gpu: pp0 - mali450 version major 0 minor 0
[   11.481421] lima d00c0000.gpu: pp1 - mali450 version major 0 minor 0
[   11.488945] debugfs: File 'HDMITX Capture' in directory 'dapm' already present!
[   11.491109] lima d00c0000.gpu: l2 cache 8K, 4-way, 64byte cache line, 128bit external bus
[   11.504851] lima d00c0000.gpu: l2 cache 64K, 4-way, 64byte cache line, 128bit external bus
[   11.523069] lima d00c0000.gpu: bus rate = 166666504
[   11.526774] lima d00c0000.gpu: mod rate = 24000000
[   11.535175] lima d00c0000.gpu: dev_pm_opp_set_regulators: no regulator (mali) found: -19
[   11.566724] [drm] Initialized lima 1.1.0 20191231 for d00c0000.gpu on minor 1
[   11.577824] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   11.736655] systemd[1]: Found device /sys/subsystem/net/devices/eth0.
[   11.985355] systemd[1]: Found device STORAGE_DEVICE BOOT.
[   12.039472] systemd[1]: Finished Helper to synchronize boot up for ifupdown.
[   12.049224] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   12.064638] systemd[1]: Starting Load Kernel Module chromeos_pstore...
[   12.078750] systemd[1]: Starting Load Kernel Module efi_pstore...
[   12.092428] systemd[1]: Starting Load Kernel Module pstore_blk...
[   12.106025] systemd[1]: Starting Load Kernel Module pstore_zone...
[   12.119653] systemd[1]: Starting Load Kernel Module ramoops...
[   12.127549] systemd[1]: Condition check resulted in Show Plymouth Boot Screen being skipped.
[   12.137349] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   12.151818] systemd[1]: Condition check resulted in Forward Password Requests to Plymouth Directory Watch being skipped.
[   12.164351] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   12.180034] systemd[1]: Starting File System Check on /dev/disk/by-label/BOOT...
[   12.193545] systemd[1]: modprobe@chromeos_pstore.service: Deactivated successfully.
[   12.200889] systemd[1]: Finished Load Kernel Module chromeos_pstore.
[   12.211543] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[   12.219017] systemd[1]: Finished Load Kernel Module efi_pstore.
[   12.228926] systemd[1]: modprobe@pstore_blk.service: Deactivated successfully.
[   12.236084] systemd[1]: Finished Load Kernel Module pstore_blk.
[   12.246492] systemd[1]: modprobe@pstore_zone.service: Deactivated successfully.
[   12.253484] systemd[1]: Finished Load Kernel Module pstore_zone.
[   12.264211] systemd[1]: modprobe@ramoops.service: Deactivated successfully.
[   12.270933] systemd[1]: Finished Load Kernel Module ramoops.
[   12.285107] systemd[1]: Started File System Check Daemon to report status.
[   12.295164] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   12.612237] systemd[1]: Finished File System Check on /dev/disk/by-label/BOOT.
[   12.634148] systemd[1]: Mounting /boot...
[   12.661857] FAT-fs (sda1): mounting with "discard" option, but the device does not support discard
[   12.679485] systemd[1]: Mounted /boot.
[   12.687643] systemd[1]: Reached target Local File Systems.
[   12.700391] systemd[1]: Starting Armbian leds state...
[   12.713401] systemd[1]: Starting Armbian ZRAM config...
[   12.726100] systemd[1]: Starting Set console font and keymap...
[   12.739302] systemd[1]: Started ifup for eth0.
[   12.752492] systemd[1]: Starting Raise network interfaces...
[   12.764965] systemd[1]: Starting Tell Plymouth To Write Out Runtime Data...
[   12.773740] systemd[1]: Condition check resulted in RPC security service for NFS server being skipped.
[   12.784556] systemd[1]: Condition check resulted in Mark the need to relabel after reboot being skipped.
[   12.803709] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   12.814231] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped.
[   12.825641] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[   12.837261] systemd[1]: Condition check resulted in Merge System Extension Images into /usr/ and /opt/ being skipped.
[   12.853072] systemd[1]: Finished Armbian leds state.
[   12.863914] systemd[1]: Finished Set console font and keymap.
[   12.874017] systemd[1]: Finished Tell Plymouth To Write Out Runtime Data.
[   12.962595] zram: Added device: zram0
[   12.967311] zram: Added device: zram1
[   12.971678] zram: Added device: zram2
[   12.978598] systemd[1]: Finished Wait for network to be configured by ifupdown.
[   13.087011] zram0: detected capacity change from 0 to 822944
[   13.119813] Adding 411468k swap on /dev/zram0.  Priority:5 extents:1 across:411468k SSFS
[   13.234368] meson8b-dwmac c9410000.ethernet eth0: PHY [0.e40908ff:08] driver [Meson GXL Internal PHY] (irq=49)
[   13.247534] zram1: detected capacity change from 0 to 102400
[   13.252143] meson8b-dwmac c9410000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   13.307142] systemd[1]: Finished Armbian ZRAM config.
[   13.320138] systemd[1]: Starting Armbian memory supported logging...
[   13.388934] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard. Quota mode: none.
[   14.784723] meson8b-dwmac c9410000.ethernet eth0: No Safety Features support found
[   14.790328] meson8b-dwmac c9410000.ethernet eth0: PTP not supported by HW
[   14.797654] meson8b-dwmac c9410000.ethernet eth0: configuring for phy/rmii link mode
[   16.760692] systemd[1]: Finished Armbian memory supported logging.
[   16.789421] systemd[1]: Starting Journal Service...
[   16.968946] systemd[1]: Started Journal Service.
[   17.004287] systemd-journald[834]: Received client request to flush runtime journal.
[   17.142591] RPC: Registered named UNIX socket transport module.
[   17.142604] RPC: Registered udp transport module.
[   17.142608] RPC: Registered tcp transport module.
[   17.142612] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   37.174721] VDDAO_3V3: disabling

Armbian 23.02.0-trunk Jammy ttyAML0

armbian login: root
Password:
    _              _   ____  ___   ___  ____  _ ____
   / \   _ __ ___ | | / ___|/ _ \ / _ \| ___|| |___ \
  / _ \ | '_ ` _ \| | \___ \ (_) | | | |___ \| | __) |
 / ___ \| | | | | | |  ___) \__, | |_| |___) | |/ __/
/_/   \_\_| |_| |_|_| |____/  /_/ \___/|____/|_|_____|

Welcome to Armbian 23.02.0-trunk Jammy with Linux 5.15.95-flippy-82+o

System load:   2%               Up time:       6 min
Memory usage:  14% of 803M      IP:
CPU temp:      34°C             Usage of /:    70% of 2.4G
storage/:      41% of 252M
RX today:      0 B

[ General system configuration (beta): armbian-config ]

Last login: Sat Feb 25 16:52:24 CST 2023 on tty1
root@armbian:~# ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether 9e:61:c2:a1:7a:aa  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 29

eth0:avahi: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 169.254.13.137  netmask 255.255.0.0  broadcast 169.254.255.255
        ether 9e:61:c2:a1:7a:aa  txqueuelen 1000  (Ethernet)
        device interrupt 29

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 32  bytes 2984 (2.9 KB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 32  bytes 2984 (2.9 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

root@armbian:~# armbian-config
Warning: Configuration cannot work properly without a working internet connection.      Press CTRL C to stop or any key to ignore and continue.
ophub / amlogic-s9xxx-armbian

MGV2000有线网口无法使用 #1108
