no boot on S905X3

[samcux]

Device Information | 设备信息

• SOC: S905x3
• Model H96 Max X3 / 64GB

Armbian Version | 系统版本

• Version: bullseye_6.1.66_server_2023.12.08.img

Does not boot from SD/USB.

Any ideas? What can I do?

Here the serial output:

SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;CHK:22;READ:0;0.0;CHK:0;
bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0001 - pwm id 0x00
bl2_stage_init 0xc0
bl2_stage_init 0x02

L0:00000000
L1:00000703
L2:00008067
L3:15000020
S1:00000000
B2:20282000
B1:a0f83180

TE: 182641

BL2 Built : 20:29:41, Jun 18 2019. g12a ga659aac - luan.yuan@droid15-sz

Board ID = 1
Set cpu clk to 24M
Set clk81 to 24M
Use GP1_pll as DSU clk.
DSU clk: 1200 Mhz
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 1
sw8 s
DDR driver_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:37
board id: 1
Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 1
fw parse done
Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 1
Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 1
PIEI prepare done
fastboot data load
00000000
emmc switch 2 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
verify result: 0
enable_fast_boot
dmc_margin_rx==12 dmc_margin_tx==12 steps
DDR3 probe
ddr clk to 672MHz
Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 1
00000000
emmc switch 1 ok

dmc_version 0001
Check phy result
INFO : End of initialization
INFO : Training has run successfully!
aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:43
DDR cs0 size: 3928MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 0000002dDDR size: 3928MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 448
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
BL2: rpmb counter: 0x000025f1
00000000
emmc switch 1 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 1
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d0000, part: 1
bl2z: ptr: 05129330, size: 00001e40
0.0;M3 CHK:0;cm4_sp_mode 0
MVN_1=0x00000000
MVN_2=0x00000000
[Image: g12a_v1.1.3389-92241b5 2019-07-02 17:22:49 luan.yuan@droid15-sz]
OPS=0x10
ring efuse init
2b 0c 10 00 01 32 1d 00 00 10 32 37 30 52 30 50
[0.017354 Inits done]
secure task start!
high task start!
low task start!
run into bl31
NOTICE:  BL31: v1.3(release):4fc40b1
NOTICE:  BL31: Built : 15:57:33, May 22 2019
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast

U-Boot 2015.01-gd0bec9fb67-dirty (Feb 08 2023 - 21:10:56)

U-Boot code: 01000000 -> 0111F028  BSS: -> 0119F660
DRAM:  Monitor len: 0019F660
Ram size: 40000000
Ram top: D8000000
TLB table from d7ff0000 to d8000000
Reserving 1661k for U-Boot at: d7e50000
Reserving 65600k for malloc() at: d3e40000
Reserving 152 Bytes for Board Info at: d3e3ff68
Reserving 320 Bytes for Global Data at: d3e3fe28

RAM Configuration:
***Bank #0: 00000000 3.7 GiB

DRAM:  3.8 GiB
New Stack Pointer is: d3e3fe10
Relocation Offset is: d6e50000
Relocation Offset is: d6e50000
Relocating to d7e50000, new gd at d3e3fe28, sp at d3e3fe10
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 00000000d7f3e770
NAND:  get_sys_clk_rate_mtd() 290, clock setting 200!
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 290, clock setting 200!
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x00000000d3e40a70
aml_priv->desc_buf = 0x00000000d3e42db0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x162000
[mmc_startup] mmc refix success
init_part() 282: PART_TYPE_DOS
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      Cannot find legal dtb!
start dts,buffer=00000000d3e45620,dt_addr=00000000d3e45620
check_valid_dts: FDT_ERR_BADMAGIC
get_partition_from_dts() 91: ret -9
get_partition_from_dts() 94: ret -9
get_ptbl_from_dtb()-272: get partition table from dts faild
mmc_device_init()-1254: get partition table from dtb failed
get_ptbl_rsv()-494: magic faild MPT,
mmc_device_init()-1281: dtb&rsv are not exist, no LPT source
get partition info failed !!
Using default environment

In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3406: calc 0, store 0
update_dtb_info()-3514: cpy 1 is not valid
_verify_dtb_checksum()-3406: calc 0, store 0
update_dtb_info()-3514: cpy 0 is not valid
dtb_read()-3623: total valid 0
emmc - EMMC sub system

Usage:
emmc dtb_read addr size
emmc dtb_write addr size
emmc erase dtb
emmc erase key
emmc fastboot_read addr size
emmc fastboot_write addr size

      Amlogic multi-dtb tool
      Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L368:Fail in fdt check header
board_late_init(): [store dtb read $dtb_mem_addr] fail
load dtb to 1000000
[store]To run cmd[emmc dtb_read 1000000 0x40000]
_verify_dtb_checksum()-3406: calc 0, store 0
update_dtb_info()-3514: cpy 1 is not valid
_verify_dtb_checksum()-3406: calc 0, store 0
update_dtb_info()-3514: cpy 0 is not valid
dtb_read()-3623: total valid 0
emmc - EMMC sub system

Usage:
emmc dtb_read addr size
emmc dtb_write addr size
emmc erase dtb
emmc erase key
emmc fastboot_read addr size
emmc fastboot_write addr size

      Amlogic multi-dtb tool
      Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L368:Fail in fdt check header
board_late_init(): store dtb read 1000000 fail
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: vpu_power_on
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
cvbs: cpuid:0x2b
Net:   dwmac.ff3f0000[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
MACADDR:02:00:00:1d:32:01(from chipid)

CONFIG_AVB2: null
Start read misc partition datas!
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb

[burnup]Err:store_read_ops,L84:cmd failed, ret=1, [store  read misc 0xd3e3f090  0x0  0x820]
failed to store read misc.
info->magic =
info->version_major = 0
info->version_minor = 0
info->slots[0].priority = 0
info->slots[0].tries_remaining = 0
info->slots[0].successful_boot = 0
info->slots[1].priority = 0
info->slots[1].tries_remaining = 0
info->slots[1].successful_boot = 0
info->crc32 = 0
Magic  is incorrect.
boot-info is invalid. Resetting.
save boot-info
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb

[burnup]Err:store_write_ops,L148:cmd [store  write misc 0xd3e3f090  0x0  0x820] failed active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=0
reboot_mode:::: cold_boot
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
hpd_state=1
edid preferred_mode is 720p60hz[4]
hdr mode is 0
dv  mode is ver:0  len: 0
hdr10+ mode is 0
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]set initrd_high: 0x3d800000
[OSD]fb_addr for logo: 0x3d800000
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=3840, height=2160
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb

[burnup]Err:store_read_ops,L84:cmd failed, ret=1, [store  read logo 0x1080000  0x0  0x2000]
Err imgread(L537):Fail to read 0x2000B from part[logo] at offset 0
There is no valid bmp file at the given address
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[1080p60hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 16
config HPLL = 5940000 frac_rate = 1
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 6  vid_clk_div = 1
hdmitx: set enc for VIC: 16
hdmitx phy setting done
enc_vpu_bridge_reset[1245]
rx version is 1.4 or below  div=10
vpp: sdr_mode = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
usblinked
InUsbBurn
noSof
sof timeout, reset usb phy tuning
card out
[MSG]mmcinfo failed!
card out
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 3000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... init_part() 282: PART_TYPE_DOS
1 Storage Device(s) found
reading aml_autoscript
709 bytes read in 27 ms (25.4 KiB/s)
## Executing script at 01080000
## Error: "bootfromsd" not defined
Saving Environment to aml-storage...
get partition info failed !!
reboot use default mode: normal
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd  1.
SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;CHK:22;READ:0;0.0;CHK:0;
bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0001 - pwm id 0x00
bl2_stage_init 0xc0
bl2_stage_init 0x02

L0:00000000
L1:00000703
L2:00008067
L3:15000020
S1:00000000
B2:20282000
B1:a0f83180

TE: 179180

BL2 Built : 20:29:41, Jun 18 2019. g12a ga659aac - luan.yuan@droid15-sz

Board ID = 1
Set cpu clk to 24M
Set clk81 to 24M
Use GP1_pll as DSU clk.
DSU clk: 1200 Mhz
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 1
sw8 s
DDR driver_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:37
board id: 1
Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 1
fw parse done
Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 1
Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 1
PIEI prepare done
fastboot data load
00000000
emmc switch 2 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
verify result: 0
enable_fast_boot
dmc_margin_rx==12 dmc_margin_tx==12 steps
DDR3 probe
ddr clk to 672MHz
Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 1
00000000
emmc switch 1 ok

dmc_version 0001
Check phy result
INFO : End of initialization
INFO : Training has run successfully!
aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:43
DDR cs0 size: 3928MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 0000002dDDR size: 3928MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 442
result report
boot times 1Enable ddr reg access
00000000
emmc switch 3 ok
BL2: rpmb counter: 0x000025f1
00000000
emmc switch 1 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 1
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d0000, part: 1
bl2z: ptr: 05129330, size: 00001e40
0.0;M3 CHK:0;cm4_sp_mode 0
MVN_1=0x00000000
MVN_2=0x00000000
[Image: g12a_v1.1.3389-92241b5 2019-07-02 17:22:49 luan.yuan@droid15-sz]
OPS=0x10
ring efuse init
2b 0c 10 00 01 32 1d 00 00 10 32 37 30 52 30 50
[0.696973 Inits done]
secure task start!
high task start!
low task start!
run into bl31
NOTICE:  BL31: v1.3(release):4fc40b1
NOTICE:  BL31: Built : 15:57:33, May 22 2019
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast

U-Boot 2015.01-gd0bec9fb67-dirty (Feb 08 2023 - 21:10:56)

U-Boot code: 01000000 -> 0111F028  BSS: -> 0119F660
DRAM:  Monitor len: 0019F660
Ram size: 40000000
Ram top: D8000000
TLB table from d7ff0000 to d8000000
Reserving 1661k for U-Boot at: d7e50000
Reserving 65600k for malloc() at: d3e40000
Reserving 152 Bytes for Board Info at: d3e3ff68
Reserving 320 Bytes for Global Data at: d3e3fe28

RAM Configuration:
***Bank #0: 00000000 3.7 GiB

DRAM:  3.8 GiB
New Stack Pointer is: d3e3fe10
Relocation Offset is: d6e50000
Relocation Offset is: d6e50000
Relocating to d7e50000, new gd at d3e3fe28, sp at d3e3fe10
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 00000000d7f3e770
NAND:  get_sys_clk_rate_mtd() 290, clock setting 200!
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 290, clock setting 200!
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x00000000d3e40a70
aml_priv->desc_buf = 0x00000000d3e42db0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x162000
[mmc_startup] mmc refix success
init_part() 282: PART_TYPE_DOS
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      Cannot find legal dtb!
start dts,buffer=00000000d3e45620,dt_addr=00000000d3e45620
check_valid_dts: FDT_ERR_BADMAGIC
get_partition_from_dts() 91: ret -9
get_partition_from_dts() 94: ret -9
get_ptbl_from_dtb()-272: get partition table from dts faild
mmc_device_init()-1254: get partition table from dtb failed
get_ptbl_rsv()-494: magic faild MPT,
mmc_device_init()-1281: dtb&rsv are not exist, no LPT source
get partition info failed !!
Using default environment

In:    serial
Out:   serial
Err:   serial
reboot_mode=normal
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3406: calc 0, store 0
update_dtb_info()-3514: cpy 1 is not valid
_verify_dtb_checksum()-3406: calc 0, store 0
update_dtb_info()-3514: cpy 0 is not valid
dtb_read()-3623: total valid 0
emmc - EMMC sub system

Usage:
emmc dtb_read addr size
emmc dtb_write addr size
emmc erase dtb
emmc erase key
emmc fastboot_read addr size
emmc fastboot_write addr size

      Amlogic multi-dtb tool
      Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L368:Fail in fdt check header
board_late_init(): [store dtb read $dtb_mem_addr] fail
load dtb to 1000000
[store]To run cmd[emmc dtb_read 1000000 0x40000]
_verify_dtb_checksum()-3406: calc 0, store 0
update_dtb_info()-3514: cpy 1 is not valid
_verify_dtb_checksum()-3406: calc 0, store 0
update_dtb_info()-3514: cpy 0 is not valid
dtb_read()-3623: total valid 0
emmc - EMMC sub system

Usage:
emmc dtb_read addr size
emmc dtb_write addr size
emmc erase dtb
emmc erase key
emmc fastboot_read addr size
emmc fastboot_write addr size

      Amlogic multi-dtb tool
      Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L368:Fail in fdt check header
board_late_init(): store dtb read 1000000 fail
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: vpu_power_on
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
cvbs: cpuid:0x2b
Net:   dwmac.ff3f0000[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
MACADDR:02:00:00:1d:32:01(from chipid)

CONFIG_AVB2: null
Start read misc partition datas!
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb

[burnup]Err:store_read_ops,L84:cmd failed, ret=1, [store  read misc 0xd3e3f090  0x0  0x820]
failed to store read misc.
info->magic =
info->version_major = 0
info->version_minor = 0
info->slots[0].priority = 0
info->slots[0].tries_remaining = 0
info->slots[0].successful_boot = 0
info->slots[1].priority = 0
info->slots[1].tries_remaining = 0
info->slots[1].successful_boot = 0
info->crc32 = 0
Magic  is incorrect.
boot-info is invalid. Resetting.
save boot-info
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb

[burnup]Err:store_write_ops,L148:cmd [store  write misc 0xd3e3f090  0x0  0x820] failed active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=0
reboot_mode:::: normal
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
hpd_state=1
edid preferred_mode is 720p60hz[4]
hdr mode is 0
dv  mode is ver:0  len: 0
hdr10+ mode is 0
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]set initrd_high: 0x3d800000
[OSD]fb_addr for logo: 0x3d800000
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=3840, height=2160
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb

[burnup]Err:store_read_ops,L84:cmd failed, ret=1, [store  read logo 0x1080000  0x0  0x2000]
Err imgread(L537):Fail to read 0x2000B from part[logo] at offset 0
There is no valid bmp file at the given address
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[1080p60hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 16
config HPLL = 5940000 frac_rate = 1
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 6  vid_clk_div = 1
hdmitx: set enc for VIC: 16
hdmitx phy setting done
enc_vpu_bridge_reset[1245]
rx version is 1.4 or below  div=10
vpp: sdr_mode = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
usblinked
InUsbBurn
noSof
sof timeout, reset usb phy tuning
card out
[MSG]mmcinfo failed!
card out
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 3000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices...

[andarezta]

edit uenv.txt use h96max x3 dtb or go to folder extlinux,rename extlinux.conf.bak ->extlinux.conf and change dtb to h96max x3 dtb in text make duplicate u-boot-x96maxplus.bin,and rename to u-boot.ext