Can't get correct display

paulopilot / arducam-osd

Automatically exported from code.google.com/p/arducam-osd

0 stars 0 forks source link

Can't get correct display #29

Closed GoogleCodeExporter closed 8 years ago

GoogleCodeExporter commented 8 years ago

I updated the latest firmware and charset. I put the elements on my panel and 
saving. 
Then I'm connecting minimOSD to ardupilot and I'm powering up both boards. 
MinimOSD it's not working until I push reset button or wait 20 seconds to power 
minimOSD after powering Ardupilot (like someone have mentioned). 
Then I only see Artificial Horizon (working properly) and not the other 
elements. 
I tried to use another Charset and I got more elements but still it's not 
working properly.

Please let me know if you need screenshot or if it's known issue I'd be glad to 
know how to solve.

Original issue reported on code.google.com by i...@coolmodels.gr on 27 Sep 2012 at 4:36

GoogleCodeExporter commented 8 years ago

Last time someone reported us that error it was relative to bad char update.
Please, there is a note on wiki's MinimOSD/troubleshot: "Video overlay 
presenting fuzzy and not well formed chars".

Original comment by sbeni...@gmail.com on 27 Sep 2012 at 6:56

GoogleCodeExporter commented 8 years ago

Was the wikipage MinimOSD/troubleshot helpful?
Did you solve the issue by following the instructions?

Original comment by sbeni...@gmail.com on 1 Oct 2012 at 10:27

GoogleCodeExporter commented 8 years ago

I'm sorry but I don't have any success...
I've tried with external feeding, nothing. Then, I've tried another computer 
but still not working.
I believe my miniosd may be defective. 
Can I do anything else or can I send it somewhere for a technical inspection?

Thank you very much.

Original comment by i...@coolmodels.gr on 2 Oct 2012 at 4:26

GoogleCodeExporter commented 8 years ago

What firmware is on your APM ArduPlane or ArduCopter?
Now I think that a screenshot would help.

Original comment by sbeni...@gmail.com on 2 Oct 2012 at 5:12

GoogleCodeExporter commented 8 years ago

I had v12 and yesterday tested with v13.
I can't send you a screenshot right now because I gave Ardupilot to a friend to 
fly with. I can only tell you that I used OSD Config v0.5.4425.14358 and 
firmware MinimOSD_19_MAV10.hex with charset MinimOSD_19.mcm and OSD_SA_v5.mcm 
and I only got an artificial horizon which was not showing well even that 
(blurring and disappearing when moving the ardupilot).

Original comment by i...@coolmodels.gr on 3 Oct 2012 at 8:05

GoogleCodeExporter commented 8 years ago

I think we did everything around the basic. The next step would be using an AVR 
programmer to: erase the chip, reload the bootloader and check/set the fuses. 
After that you would re-upload the firmware and try it. If you are no 
experienced on this, please contact the 3DR technical support.

Original comment by sbeni...@gmail.com on 12 Oct 2012 at 11:16

GoogleCodeExporter commented 8 years ago

Thanks for your support!
I'm not really sure how to do that...
Can you tell me how to find a way to contact 3DR Support?
I'm willing to send this OSD for technical inspection and repair if needed.

Thanks Again!

Original comment by i...@coolmodels.gr on 12 Oct 2012 at 4:19

GoogleCodeExporter commented 8 years ago

Here goes the info from 3DR store:
"For further hardware support or technical questions please email us at: 
help@3drobotics.com".

Original comment by sbeni...@gmail.com on 13 Oct 2012 at 1:38

Changed state: Done