search

pcengines / coreboot

github mirror of coreboot.org's master repository
http://www.coreboot.org/
GNU General Public License v2.0
73 stars 11 forks source link

apu2 v4.8.0.4 breaks WLE200NX wifi cards #206

Closed muzy closed 5 years ago

muzy commented 6 years ago

Hi,

I just found out that by flashing the apu2 v4.8.0.4 bios to my APU2C4, my Compex WLE200NX wifi cards did no longer broadcast any SSID. Unfortunately there is no error in the kernel log or the hostapd debug messages.

When switching to apu2 v4.6.9 bios, the wifi cards did work again.

Any ideas on how to debug this?

pietrushnic commented 6 years ago

@muzy sounds quite weird. I assume you tested that couple times and this is reproducible?

IIRC we have WLE200NX on board so we can test your scenario and see if this happen on our side. @miczyg1 let's try to address that in v4.8.0.6 iteration

miczyg1 commented 6 years ago

@muzy what operating system are You using? It would be better to stick to Your configuration as close as possible. Which slot was the card plugged in, mPCIe 1 or mPCIe 2?

muzy commented 6 years ago

I was finally able to debug a more and conducted the following test matrix on multiple APU2C4 devices with two Compex WLE200NX in mPCIe 1 and mPCIe2, booted from SD card:

Coreboot Debian 9.5 OpenWRT 18.06.1
4.8.0.4 not working working
4.6.10 working working

Software Versions are as follows: Debian 9.5: hostapd 2.4 OpenWRT 18.06.1: hostapd 2.7

Output of lspci for wifi cards:

01:00.0 Network controller: Qualcomm Atheros AR928X Wireless Network Adapter (PCI-Express) (rev 01)
05:00.0 Network controller: Qualcomm Atheros AR928X Wireless Network Adapter (PCI-Express) (rev 01)

While conducting the tests I noted a difference in the hostapd debug output on the Debian 9.5. The only thing changed between tests is Coreboot version. The hostapd configuration for reproducing the test result is as follows:

beacon_int=100
ssid=TEST
interface=wlp5s0
driver=nl80211
channel=6
ctrl_interface=/var/run/hostapd_wlp5s0
ctrl_interface_group=0
ignore_broadcast_ssid=0
ap_isolate=0
hw_mode=g
ieee80211n=1
ht_capab=[HT20]
wpa=2
wpa_passphrase=testtest123
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP CCMP
rsn_pairwise=CCMP
bridge=br0

This is the output from both test runs on Debian 9.5 (Click to toggle output). It appears that hostapd stops with the 4.8.0.4 Coreboot while waiting for some sort of command.

**hostapd with 4.8.0.4**

``` random: Trying to read entropy from /dev/random Configuration file: hostapd.conf ctrl_interface_group=0 rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0 nl80211: TDLS supported nl80211: TDLS external setup nl80211: Supported cipher 00-0f-ac:1 nl80211: Supported cipher 00-0f-ac:5 nl80211: Supported cipher 00-0f-ac:2 nl80211: Supported cipher 00-0f-ac:4 nl80211: Supported cipher 00-0f-ac:10 nl80211: Supported cipher 00-0f-ac:8 nl80211: Supported cipher 00-0f-ac:9 nl80211: Supported cipher 00-0f-ac:6 nl80211: Supported cipher 00-0f-ac:13 nl80211: Supported cipher 00-0f-ac:11 nl80211: Supported cipher 00-0f-ac:12 nl80211: Using driver-based off-channel TX nl80211: Use separate P2P group interface (driver advertised support) nl80211: interface wlp5s0 in phy phy1 nl80211: Set mode ifindex 6 iftype 3 (AP) nl80211: Setup AP(wlp5s0) - device_ap_sme=0 use_monitor=0 nl80211: Subscribe to mgmt frames with AP handle 0x562da657b0e0 nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x562da657b0e0 match= nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ) nl_handle=0x562da657b0e0 match= nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ) nl_handle=0x562da657b0e0 match= nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC) nl_handle=0x562da657b0e0 match= nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH) nl_handle=0x562da657b0e0 match= nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x562da657b0e0 match= nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x562da657b0e0 match= nl80211: Add own interface ifindex 7 nl80211: if_indices[16]: 7 nl80211: Add own interface ifindex 6 nl80211: if_indices[16]: 7 6 nl80211: Adding interface wlp5s0 into bridge br0 phy: phy1 BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) nl80211: Regulatory information - country=US (DFS-FCC) nl80211: 2402-2472 @ 40 MHz 30 mBm nl80211: 5170-5250 @ 80 MHz 23 mBm nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS) nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS) nl80211: 5735-5835 @ 80 MHz 30 mBm nl80211: 57240-63720 @ 2160 MHz 40 mBm nl80211: Added 802.11b mode based on 802.11g information hw vht capab: 0x0, conf vht capab: 0x0 Completing interface initialization Mode: IEEE 802.11g Channel: 6 Frequency: 2437 MHz DFS 0 channels required radar detection nl80211: Set freq 2437 (ht_enabled=1, vht_enabled=0, bandwidth=20 MHz, cf1=2437 MHz, cf2=0 MHz) * freq=2437 * vht_enabled=0 * ht_enabled=1 * sec_channel_offset=0 * channel_type=1 RATE[0] rate=10 flags=0x1 RATE[1] rate=20 flags=0x1 RATE[2] rate=55 flags=0x1 RATE[3] rate=110 flags=0x1 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 hostapd_setup_bss(hapd=0x562da657b900 (wlp5s0), first=1) wlp5s0: Flushing old station entries nl80211: flush -> DEL_STATION wlp5s0 (all) wlp5s0: Deauthenticate all stations nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2437 wait=0) wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0 Using interface wlp5s0 with hwaddr 04:f0:21:3b:39:67 and ssid "TEST" Deriving WPA PSK based on passphrase SSID - hexdump_ascii(len=4): 54 45 53 54 TEST PSK (ASCII passphrase) - hexdump_ascii(len=11): [REMOVED] PSK (from passphrase) - hexdump(len=32): [REMOVED] random: Got 20/20 bytes from /dev/random GMK - hexdump(len=32): [REMOVED] Key Counter - hexdump(len=32): [REMOVED] WPA: Delay group state machine start until Beacon frames have been configured nl80211: Set beacon (beacon_set=0) nl80211: Beacon head - hexdump(len=55): 80 00 00 00 ff ff ff ff ff ff 04 f0 21 3b 39 67 04 f0 21 3b 39 67 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 04 54 45 53 54 01 08 82 84 8b 96 0c 12 18 24 03 01 06 nl80211: Beacon tail - hexdump(len=119): 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 0c 00 2d 1a 0c 00 1b ff ff 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 3d 16 06 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7f 08 00 00 00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 00 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 nl80211: ifindex=6 nl80211: beacon_int=100 nl80211: dtim_period=2 nl80211: ssid - hexdump_ascii(len=4): 54 45 53 54 TEST * beacon_int=100 nl80211: hidden SSID not in use nl80211: privacy=1 nl80211: auth_algs=0x3 nl80211: wpa_version=0x2 nl80211: key_mgmt_suites=0x2 nl80211: pairwise_ciphers=0x18 nl80211: group_cipher=0x10 nl80211: SMPS mode - off nl80211: beacon_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40 nl80211: proberesp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40 nl80211: assocresp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40 WPA: Start group state machine to set initial keys WPA: group state machine entering state GTK_INIT (VLAN-ID 0) GTK - hexdump(len=16): [REMOVED] WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=3 addr=0x562da5c02231 key_idx=1 set_tx=1 seq_len=0 key_len=16 nl80211: KEY_DATA - hexdump(len=16): [REMOVED] broadcast key nl80211: Set wlp5s0 operstate 0->1 (UP) netlink: Operstate: ifindex=6 linkmode=-1 (no change), operstate=6 (IF_OPER_UP) wlp5s0: interface state UNINITIALIZED->ENABLED wlp5s0: AP-ENABLED wlp5s0: Setup of interface done. ctrl_iface not configured! RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=2 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=2 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=2 linkmode=0 master=7 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=2 linkmode=0 master=7 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=2 ifi_family=7 ifi_flags=0x1003 ([UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=6 linkmode=0 master=7 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) RTM_NEWLINK: ifi_index=7 ifname=br0 operstate=6 linkmode=0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) wlp5s0: Event INTERFACE_STATUS (5) received Unknown event 5 VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) VLAN: RTM_NEWLINK: ifi_index=7 ifname=br0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(br0) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) ```

**hostapd with 4.6.10**

``` random: Trying to read entropy from /dev/random Configuration file: hostapd.conf ctrl_interface_group=0 rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0 nl80211: TDLS supported nl80211: TDLS external setup nl80211: Supported cipher 00-0f-ac:1 nl80211: Supported cipher 00-0f-ac:5 nl80211: Supported cipher 00-0f-ac:2 nl80211: Supported cipher 00-0f-ac:4 nl80211: Supported cipher 00-0f-ac:10 nl80211: Supported cipher 00-0f-ac:8 nl80211: Supported cipher 00-0f-ac:9 nl80211: Supported cipher 00-0f-ac:6 nl80211: Supported cipher 00-0f-ac:13 nl80211: Supported cipher 00-0f-ac:11 nl80211: Supported cipher 00-0f-ac:12 nl80211: Using driver-based off-channel TX nl80211: Use separate P2P group interface (driver advertised support) nl80211: interface wlp5s0 in phy phy1 nl80211: Set mode ifindex 6 iftype 3 (AP) nl80211: Setup AP(wlp5s0) - device_ap_sme=0 use_monitor=0 nl80211: Subscribe to mgmt frames with AP handle 0x5632292b10e0 nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x5632292b10e0 match= nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ) nl_handle=0x5632292b10e0 match= nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ) nl_handle=0x5632292b10e0 match= nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC) nl_handle=0x5632292b10e0 match= nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH) nl_handle=0x5632292b10e0 match= nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5632292b10e0 match= nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x5632292b10e0 match= nl80211: Add own interface ifindex 7 nl80211: if_indices[16]: 7 nl80211: Add own interface ifindex 6 nl80211: if_indices[16]: 7 6 nl80211: Adding interface wlp5s0 into bridge br0 phy: phy1 BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) nl80211: Regulatory information - country=US (DFS-FCC) nl80211: 2402-2472 @ 40 MHz 30 mBm nl80211: 5170-5250 @ 80 MHz 23 mBm nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS) nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS) nl80211: 5735-5835 @ 80 MHz 30 mBm nl80211: 57240-63720 @ 2160 MHz 40 mBm nl80211: Added 802.11b mode based on 802.11g information hw vht capab: 0x0, conf vht capab: 0x0 Completing interface initialization Mode: IEEE 802.11g Channel: 6 Frequency: 2437 MHz DFS 0 channels required radar detection nl80211: Set freq 2437 (ht_enabled=1, vht_enabled=0, bandwidth=20 MHz, cf1=2437 MHz, cf2=0 MHz) * freq=2437 * vht_enabled=0 * ht_enabled=1 * sec_channel_offset=0 * channel_type=1 RATE[0] rate=10 flags=0x1 RATE[1] rate=20 flags=0x1 RATE[2] rate=55 flags=0x1 RATE[3] rate=110 flags=0x1 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 hostapd_setup_bss(hapd=0x5632292b1900 (wlp5s0), first=1) wlp5s0: Flushing old station entries nl80211: flush -> DEL_STATION wlp5s0 (all) wlp5s0: Deauthenticate all stations nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2437 wait=0) wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0 Using interface wlp5s0 with hwaddr 04:f0:21:3b:39:67 and ssid "TEST" Deriving WPA PSK based on passphrase SSID - hexdump_ascii(len=4): 54 45 53 54 TEST PSK (ASCII passphrase) - hexdump_ascii(len=11): [REMOVED] PSK (from passphrase) - hexdump(len=32): [REMOVED] random: Got 20/20 bytes from /dev/random GMK - hexdump(len=32): [REMOVED] Key Counter - hexdump(len=32): [REMOVED] WPA: Delay group state machine start until Beacon frames have been configured nl80211: Set beacon (beacon_set=0) nl80211: Beacon head - hexdump(len=55): 80 00 00 00 ff ff ff ff ff ff 04 f0 21 3b 39 67 04 f0 21 3b 39 67 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 04 54 45 53 54 01 08 82 84 8b 96 0c 12 18 24 03 01 06 nl80211: Beacon tail - hexdump(len=119): 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 0c 00 2d 1a 0c 00 1b ff ff 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 3d 16 06 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7f 08 00 00 00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 00 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 nl80211: ifindex=6 nl80211: beacon_int=100 nl80211: dtim_period=2 nl80211: ssid - hexdump_ascii(len=4): 54 45 53 54 TEST * beacon_int=100 nl80211: hidden SSID not in use nl80211: privacy=1 nl80211: auth_algs=0x3 nl80211: wpa_version=0x2 nl80211: key_mgmt_suites=0x2 nl80211: pairwise_ciphers=0x18 nl80211: group_cipher=0x10 nl80211: SMPS mode - off nl80211: beacon_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40 nl80211: proberesp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40 nl80211: assocresp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40 WPA: Start group state machine to set initial keys WPA: group state machine entering state GTK_INIT (VLAN-ID 0) GTK - hexdump(len=16): [REMOVED] WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) wpa_driver_nl80211_set_key: ifindex=6 (wlp5s0) alg=3 addr=0x563228af1231 key_idx=1 set_tx=1 seq_len=0 key_len=16 nl80211: KEY_DATA - hexdump(len=16): [REMOVED] broadcast key nl80211: Set wlp5s0 operstate 0->1 (UP) netlink: Operstate: ifindex=6 linkmode=-1 (no change), operstate=6 (IF_OPER_UP) wlp5s0: interface state UNINITIALIZED->ENABLED wlp5s0: AP-ENABLED wlp5s0: Setup of interface done. ctrl_iface not configured! RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=2 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=2 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=2 linkmode=0 master=7 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=2 linkmode=0 master=7 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=2 ifi_family=7 ifi_flags=0x1003 ([UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 operstate=6 linkmode=0 master=7 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) RTM_NEWLINK: ifi_index=7 ifname=br0 operstate=6 linkmode=0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) wlp5s0: Event INTERFACE_STATUS (5) received Unknown event 5 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=94:9f:3e:1b:6c:4d freq=2412 ssi_signal=-41 fc=0x40 seq_ctrl=0x2cd0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=125 STA 94:9f:3e:1b:6c:4d sent probe request without SSID or supported rates element VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) VLAN: RTM_NEWLINK: ifi_index=7 ifname=br0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(br0) nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-67 fc=0x40 seq_ctrl=0x6730 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-61 fc=0x40 seq_ctrl=0x6740 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-62 fc=0x40 seq_ctrl=0x6750 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-64 fc=0x40 seq_ctrl=0x6760 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-28 fc=0x40 seq_ctrl=0x6800 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-29 fc=0x40 seq_ctrl=0x6810 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-29 fc=0x40 seq_ctrl=0x6820 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-29 fc=0x40 seq_ctrl=0x6830 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-29 fc=0x40 seq_ctrl=0x6840 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-29 fc=0x40 seq_ctrl=0x6850 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-30 fc=0x40 seq_ctrl=0x6860 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-29 fc=0x40 seq_ctrl=0x6870 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-29 fc=0x40 seq_ctrl=0x6880 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-28 fc=0x40 seq_ctrl=0x6890 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-28 fc=0x40 seq_ctrl=0x68a0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-28 fc=0x40 seq_ctrl=0x68b0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-61 fc=0x40 seq_ctrl=0x6950 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-62 fc=0x40 seq_ctrl=0x6990 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=51 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=78:11:dc:ed:01:fb freq=2437 ssi_signal=-62 fc=0x40 seq_ctrl=0x69a0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=42 nl80211: send_mlme - da= 78:11:dc:ed:01:fb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=ea:0e:14:21:d3:cb freq=2437 ssi_signal=-81 fc=0x40 seq_ctrl=0x1d40 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=105 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=ea:0e:14:21:d3:cb freq=2437 ssi_signal=-76 fc=0x40 seq_ctrl=0x1d60 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=105 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=48:d6:d5:1d:a1:d2 freq=2437 ssi_signal=-82 fc=0x40 seq_ctrl=0x1ec0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=97 nl80211: send_mlme - da= 48:d6:d5:1d:a1:d2 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x2f60 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=5 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x2f70 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=5 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-37 fc=0x40 seq_ctrl=0x2f80 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=5 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-39 fc=0x40 seq_ctrl=0x2f90 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:68:a7:e5 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-39 fc=0x40 seq_ctrl=0x2fa0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:68:a7:e5 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x2fb0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:68:a7:e5 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x2fc0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:68:a7:e5 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x2fd0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:68:a7:e5 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-37 fc=0x40 seq_ctrl=0x2fe0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=7 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-37 fc=0x40 seq_ctrl=0x2ff0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=7 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:68:a7:e5 freq=2437 ssi_signal=-37 fc=0x40 seq_ctrl=0x3000 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=7 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=ea:0e:14:21:d3:cb freq=2437 ssi_signal=-75 fc=0x40 seq_ctrl=0x2090 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=94 nl80211: send_mlme - da= ea:0e:14:21:d3:cb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=ea:0e:14:21:d3:cb freq=2437 ssi_signal=-76 fc=0x40 seq_ctrl=0x20a0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=105 RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 master=7 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) nl80211: Add ifindex 7 for bridge br0 nl80211: Add own interface ifindex 7 nl80211: ifindex 7 already in the list VLAN: RTM_NEWLINK: ifi_index=6 ifname=wlp5s0 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) VLAN: vlan_newlink(wlp5s0) nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=ea:0e:14:21:d3:cb freq=2437 ssi_signal=-74 fc=0x40 seq_ctrl=0x23c0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=105 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=a0:88:b4:60:44:c0 freq=2437 ssi_signal=-53 fc=0x40 seq_ctrl=0x2c50 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=70 nl80211: send_mlme - da= a0:88:b4:60:44:c0 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=a0:88:b4:60:44:c0 freq=2437 ssi_signal=-41 fc=0x40 seq_ctrl=0x2c60 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=70 nl80211: send_mlme - da= a0:88:b4:60:44:c0 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=a0:88:b4:60:44:c0 freq=2437 ssi_signal=-14 fc=0x40 seq_ctrl=0x2c90 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=70 nl80211: send_mlme - da= a0:88:b4:60:44:c0 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=a0:88:b4:60:44:c0 freq=2437 ssi_signal=-15 fc=0x40 seq_ctrl=0x2cb0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=70 nl80211: send_mlme - da= a0:88:b4:60:44:c0 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=a0:88:b4:60:44:c0 freq=2437 ssi_signal=-48 fc=0x40 seq_ctrl=0x2cf0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=70 nl80211: send_mlme - da= a0:88:b4:60:44:c0 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-37 fc=0x40 seq_ctrl=0x32e0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=5 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-36 fc=0x40 seq_ctrl=0x32f0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=5 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-37 fc=0x40 seq_ctrl=0x3300 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=5 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x3310 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:81:5b:5e noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-39 fc=0x40 seq_ctrl=0x3320 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:81:5b:5e noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x3330 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:81:5b:5e noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x3340 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:81:5b:5e noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-39 fc=0x40 seq_ctrl=0x3350 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 nl80211: send_mlme - da= da:a1:19:81:5b:5e noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-37 fc=0x40 seq_ctrl=0x3360 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=7 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x3370 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=7 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=da:a1:19:81:5b:5e freq=2437 ssi_signal=-38 fc=0x40 seq_ctrl=0x3380 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=82 Ignore Probe Request due to DS Params mismatch: chan=6 != ds.chan=7 nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 nl80211: RX frame sa=ea:0e:14:21:d3:cb freq=2437 ssi_signal=-76 fc=0x40 seq_ctrl=0x2710 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=94 nl80211: send_mlme - da= ea:0e:14:21:d3:cb noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2437 nl80211: send_frame -> send_frame_cmd nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlp5s0 ```

If I can be of any assistance while debugging please let me know. I'd be happy to help.

pietrushnic commented 6 years ago

@miczyg1 does it sound like clock related stuff?

@muzy can you play with m Force mPCIe2 slot CLK (GPP3 PCIe) described in sortbootorder here? Let's try to change only that option on not working firmware and see if it fix things.

miczyg1 commented 6 years ago

@pietrushnic it looks so. @muzy try the mPCIe2 CLK quirk in sortbootorder. We will try to figure something out on our side too.

muzy commented 6 years ago

@miczyg1 @pietrushnic I tried the mPCIe2 CLK option and left everything else as it was before (Debian 9.5, hostapd config). The observable effects are the same (the log file output from hostapd is the same).

pietrushnic commented 6 years ago

@muzy we have to reproduce that on our side any simple guide or maybe ready to use system images that we can use? @miczyg1 I'm not sure what would be best approach here, but maybe some debug build with spew logging and then trying to compare 2 boots?

muzy commented 6 years ago

@pietrushnic I've uploaded a copy of the image here: https://ufile.io/2mmjv

You need to unzip the image with gzip/gunzip and then copy the image to an SD card with at least 16GB using the dd utility.

SHA1 hash of the image (unzipped): 4182a222f302dddef2bf81601a9567cf69cfc68e
User/PW: root/test123
pietrushnic commented 6 years ago

@miczyg1 let's try that next week.

miczyg1 commented 6 years ago

@muzy I have finally found some free cycles to look into the issue. I have burned Your image onto SD card, but I face little problems from the start:

I would appreciate any advices since I am not aware of all modifications and settings You have made to the system.

muzy commented 6 years ago

@miczyg1 what you see is very unexpected. I'll check and reach out. The bridges should have no influence as they are used for docker only.

miczyg1 commented 6 years ago

@muzy I will try preparing a fresh installation with hostapd only and copy Your configs. Hope to get some results.

miczyg1 commented 6 years ago

@muzy I guess I have found the issue with non-existing interface. The wireless interface is not going up automatically after boot. I have to explicitly call ifconfig wlpXsX up. I will workaround lack of second wifi card somehow. Could You please tell me how the bridges are created (which interfaces are bridged)? I would like to reproduce Your configuration to make it as close to Yours as possible.

miczyg1 commented 6 years ago

@muzy I managed to get SSID broadcasted on WLE200NX with v4.8.0.4 and v4.6.10. It looks like AMD IOMMU causes some malfunctions, it was introduced in v4.8.0.3. As a mere workaround You can add amd_iommu=off to kernel cmdline to turn it off. After that my phone started to discover the TEST wifi network on v4.8.0.4.

Please note that IOMMU is quite fresh feature on PC Engines platforms and may not yet be perfectly initialized.

miczyg1 commented 6 years ago

Related issue: https://github.com/pcengines/coreboot/issues/200

miczyg1 commented 5 years ago

@muzy did the amd_iommu=off help?

miczyg1 commented 5 years ago

@muzy if the quirk did not help for You, feel free to reopen the issue. Closing it for now.

thillux commented 5 years ago

intremap=off helped me. I assume the ath9k driver isn't using the IOMMU correctly.

chr0mag commented 5 years ago

I'm not sure this merits reopening (or even if it's something fixable by PC Engines) but after adding amd_iommu=off to workaround this issue, I see the following stack trace in dmesg on boot.

My device recovers and boots normally and turning off iommu does allow me to see my WLE200NX SSID again.

WARNING: CPU: 0 PID: 0 at kernel/workqueue.c:2771 flush_workqueue+0x3ca/0x420
Jul 10 20:49:39 apu2c4 kernel: Modules linked in:
Jul 10 20:49:39 apu2c4 kernel: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.1.16-arch1-1-ARCH #1
Jul 10 20:49:39 apu2c4 kernel: Hardware name: PC Engines apu2/apu2, BIOS v4.9.0.5 05/09/2019
Jul 10 20:49:39 apu2c4 kernel: RIP: 0010:flush_workqueue+0x3ca/0x420
Jul 10 20:49:39 apu2c4 kernel: Code: ff ff ff 4c 89 e7 48 89 0c 24 e8 51 f1 ff ff 41 8b 44 24 44 41 8b 74 24 40 48 8b 0c 24 e9 f8 fe ff ff 4c 89 fb e9 77 fe ff ff <0f> >
Jul 10 20:49:39 apu2c4 kernel: RSP: 0000:ffffffffac003d60 EFLAGS: 00010246
Jul 10 20:49:39 apu2c4 kernel: RAX: ffffffffac003d98 RBX: ffff8cdeea439980 RCX: 0000000000000000
Jul 10 20:49:39 apu2c4 kernel: RDX: ffffffffac67bc48 RSI: ffffffffabe98042 RDI: ffffffffac003d90
Jul 10 20:49:39 apu2c4 kernel: RBP: ffffffffac003de0 R08: 0000000000000000 R09: 0000000000000000
Jul 10 20:49:39 apu2c4 kernel: R10: ffffebc1c4a95608 R11: 0000000000000000 R12: 0000000000000000
Jul 10 20:49:39 apu2c4 kernel: R13: ffffffffac003d70 R14: 0000000000000501 R15: 0000000000010c01
Jul 10 20:49:39 apu2c4 kernel: FS:  0000000000000000(0000) GS:ffff8cdeeaa00000(0000) knlGS:0000000000000000
Jul 10 20:49:39 apu2c4 kernel: CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Jul 10 20:49:39 apu2c4 kernel: CR2: ffff8cdeeefff000 CR3: 000000003420e000 CR4: 00000000000406b0
Jul 10 20:49:39 apu2c4 kernel: Call Trace:
Jul 10 20:49:39 apu2c4 kernel:  kmem_cache_destroy+0x5b/0x200
Jul 10 20:49:39 apu2c4 kernel:  ? __free_pages_ok+0x156/0x2c0
Jul 10 20:49:39 apu2c4 kernel:  free_iommu_resources+0x5a/0x191
Jul 10 20:49:39 apu2c4 kernel:  iommu_go_to_state+0xafd/0x12ef
Jul 10 20:49:39 apu2c4 kernel:  amd_iommu_prepare+0x16/0x2a
Jul 10 20:49:39 apu2c4 kernel:  irq_remapping_prepare+0x36/0x5f
Jul 10 20:49:39 apu2c4 kernel:  enable_IR_x2apic+0x21/0x188
Jul 10 20:49:39 apu2c4 kernel:  default_setup_apic_routing+0x12/0x6f
Jul 10 20:49:39 apu2c4 kernel:  apic_intr_mode_init+0x15c/0x197
Jul 10 20:49:39 apu2c4 kernel:  x86_late_time_init+0x17/0x1c
Jul 10 20:49:39 apu2c4 kernel:  start_kernel+0x47c/0x530
Jul 10 20:49:39 apu2c4 kernel:  secondary_startup_64+0xa4/0xb0
Jul 10 20:49:39 apu2c4 kernel: ---[ end trace 1d30ed0ae73a58ff ]---
miczyg1 commented 5 years ago

@chr0mag I saw similar issues on different AMD platform running coreboot and kernel >= 4.19.x. It rather qualifies for a new issue so I would prefer You open a new one. Also provide some more detailed infornation: platform name, BIOS version, operating system version, extensuon cards used, which slots are occupied, the boot medium type (USB, SATA...) etc.

chr0mag commented 5 years ago

I've opened issue #323 for this.