issues
search
pellcorp
/
creality
25
stars
4
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
remove octoeverywhere from service list
#165
pellcorp
opened
2 days ago
0
BIQU Microprobe Mounting
#164
MrmysteryV
opened
5 days ago
1
if a user chooses to switch to an alternate klipper version do not fo…
#163
pellcorp
closed
1 week ago
0
if a print is cannceled and set velocity limits are not reset before …
#162
pellcorp
closed
1 week ago
0
allow passing in a cartographer model via start print
#161
pellcorp
closed
1 week ago
0
Mainline klipper?
#160
MrmysteryV
closed
1 week ago
2
don't need to stop and start the camera for cartotouch anymore
#159
pellcorp
closed
2 weeks ago
0
Add filament sensor control into start and end print macro
#158
TrainAss
closed
2 weeks ago
5
Option '__action__' is not valid in section 'filament_switch_sensor filament_sensor_2' after update
#157
TrainAss
closed
2 weeks ago
4
consider doing fractions of bed warping if bed is already above 60c
#156
pellcorp
closed
3 weeks ago
0
thanks to Zero for investigating using adaptive webcam
#155
pellcorp
closed
3 weeks ago
0
remove pellcorp from Moonraker.conf
#154
pellcorp
closed
3 weeks ago
0
use adaptive mode for camera
#153
pellcorp
closed
3 weeks ago
0
make it possible to use carto 5.0.0 firmware for scan rather than touch
#152
pellcorp
closed
3 weeks ago
0
Thanks to Zero for bed stabilisation feature
#151
pellcorp
closed
3 weeks ago
0
support adding additional fans to fan_control.cfg
#150
pellcorp
closed
3 weeks ago
0
allow fan_control.cfg limited overrides
#149
pellcorp
closed
3 weeks ago
0
make sure moonraker secrets is not version controlled
#148
pellcorp
closed
4 weeks ago
0
add a cleanup macro for printer cfg backups
#147
pellcorp
closed
4 weeks ago
0
remove square corner velocity from being overriden
#146
pellcorp
closed
1 month ago
0
play around with set velocity limits
#145
pellcorp
closed
1 month ago
0
optimize timeout to turn off heaters if not paused
#144
pellcorp
closed
3 weeks ago
0
simplify probe installation and configure the max position y offsets …
#143
pellcorp
closed
1 month ago
0
do a bit of cleanup of start end macros
#142
pellcorp
closed
1 month ago
0
klipper_tmc_autotune
#141
000AXR
opened
1 month ago
8
Will not home after Print
#140
Face-WASPS
opened
1 month ago
0
fix up the force move issue and also move nozzle to middle of bed aft…
#139
pellcorp
closed
1 month ago
0
tweaks to sensorless to move bed away on first home
#138
pellcorp
closed
1 month ago
0
make update just do config files rather than introducing new update-c…
#137
pellcorp
closed
1 month ago
0
make it possible to switch klipper repos from installer.sh
#136
pellcorp
closed
1 month ago
0
Suggestion for new End Print macro
#135
TrainAss
opened
1 month ago
2
add support for update-config mode
#134
pellcorp
closed
1 month ago
0
made a start for m600 command
#133
pellcorp
closed
1 month ago
0
force the use of k1-carto-klipper when using either a cartographer or…
#132
pellcorp
closed
1 month ago
0
Jp cleanup cartotouch config
#131
pellcorp
closed
1 month ago
1
set the btt eddy zoffset in printer.cfg
#130
pellcorp
closed
1 month ago
0
Force bed move when homing to prevent damage
#129
TrainAss
closed
1 month ago
3
Fan Controls
#128
TrainAss
closed
3 weeks ago
1
add a beep command yo
#127
pellcorp
closed
1 month ago
0
Make switch-default-ui.sh survice a new --install, --reinstall or --update
#126
pellcorp
opened
1 month ago
0
M600 and Filament Management
#125
TrainAss
opened
1 month ago
6
add carto touch support
#124
pellcorp
closed
1 month ago
0
Carto Touch support
#123
pellcorp
closed
1 month ago
1
fan monitoring
#122
pellcorp
opened
1 month ago
0
add fan feedback for MCU and heat break fan thanks to Dylwad
#121
pellcorp
closed
1 month ago
0
increase timeout of MCU controller fan
#120
pellcorp
closed
1 month ago
0
mjpeg_streamer very often black screen in fluid
#119
Sekilsgs2
closed
1 month ago
4
Config overrides do not support applying new sections to printer.cfg
#118
pellcorp
closed
1 month ago
1
basic support for adding overrides into a target after a specified ex…
#117
pellcorp
closed
1 month ago
0
Jp config override ignore core files
#116
pellcorp
closed
2 months ago
0
Next