Good evening.
It's me again.
After several tests I can now say that the chargen font is not displayed on the PI1541 RPi2b.
TrackDisplay and Temperature do not work either.
The same options.txt in the RPi3 works fine.
`// Sample options.txt configuration file for Pi1541
// If you would like to change the drive number then specify it here (8 is the default)
deviceID = 9
// If you are using the split line hardware option (ie Option B) then you need to specify this option
splitIECLines = 1
// If you are using some type of hardware that requires the lines to be inverted then specify these options here
//invertIECInputs = 1
//If you are using a 7407
//invertIECOutputs = 0
// If you are using the Pi's composite video out then these options allow you to experiment with the display resolution
//ScreenWidth = 512
//ScreenHeight = 384
// By default Pi1541 will search the root of the SD card for a ROM file and use this for ROM1.
// The first file found with either of the following names will be used; d1541.rom, dos1541, d1541II, Jiffy.bin
// You can override the default ROM1 by specifying it here
//ROM1 = YourDefaultRom
// You can specify additional ROMS here (up to 7)
// You can then use the function keys (F1-F7) on the keyboard to change which one you would like to use (only in browse mode and not in emulation mode)
// You can also use the buttons to swap ROMs by holding down button 1 and pressing one other buttons 2-5
// .LST files can also specify one of these ROMS that will automatically be selected when the LST file is loaded.
//ROM2 = Jiffy.bin
//ROM3 = d1541II
// Reference you 1581 ROM here
//ROM1581 = 1581-rom.318045-02.bin
//ROM1581 = JiffyDOS_1581.bin
// The rate (in seconds) a long selection is scrolled
scrollHighlightRate = 0.09
// If using CBMFileBrowser then it is best to specify this option. When the computer resets the Pi will always revert back to the root folder ready to load CBMFileBrowser again.
OnResetChangeToStartingFolder = 1
// If you use FB64 (CBMFileBrowser) and want to use a fast loader cartridge (AR6, EFL, FC3) to load it then use this option to automatically mount it.
//AutoMountImage = fb.d64 // You MUST have a disk image in \1541 with this filename
// If you use FB64 (CBMFileBrowser) and want Pi1541 to send all file names as lower case.
//LowercaseBrowseModeFilenames = 1
// If you are using a FB128 in 128 mode you can get FB128 to auto boot using this option
//AutoBootFB128 = 1
// If you are using a 128 you can auto boot anything using this option
// This over-rides AutoBootFB128
//128BootSectorName = bootsect.128
// If you would ever like to disable browse mode completely you can do so here
//DisableSD2IECCommands = 1
// This option displays the IEC bus activity on the bottom of the Pi's screen
GraphIEC = 1
// If you have hardware with a peizo buzzer (the type without a generator) then you can use this option to hear the head step
SoundOnGPIO = 1
SoundOnGPIODuration = 100 // Length of buzz in micro seconds
SoundOnGPIOFreq = 200 // Frequency of buzz in Hz
// You can create 320x200 PNG files with the same name as your disk images. With this option turned on they will be displayed on the Pi's screen.
//DisplayPNGIcons = 1
// If you would like to specify what file will be loaded by LOAD"*" in browse mode then specify it here
//StarFileName = somefile
// Alt-N creates a new disk image.
// Names are formed automatically as autoname001.d64, autoname002.d64 etc...
// change the base of the filename here
//AutoBaseName = autoname
// By default Alt-N creates a new D64 disk image.
// If you rather it create a G64 then use this option.
//NewDiskType = g64
// If you are using a LCD screen then specify it here
LCDName = ssd1306_128x64
//LCDName = ssd1306_128x32
//LCDName = sh1106_128x64
// If you are using a LCD screen and you would like PageUp and PageDown keys to work with it (rather than the HDMI screen) then specify this option
//KeyboardBrowseLCDScreen = 1
// change startup logo on oled - 1541ii or 1541classic
//LcdLogoName = 1541ii
//LcdLogoName = 1541classic
//LcdLogoName = customfile.raw
// If you are using I2C LCD you can optionally change what pins it is connected to.
// (defaults to 0 for non-split lines (Option A) or 1 for split lines (Option B))
//i2cBusMaster = 0 //SDA - pin 27 SCL - pin 28
i2cBusMaster = 1 //SDA - pin 3 SCL - pin 5
//i2cLcdAddress = 60 // I2C display address in decimal and shifted. 60 == 0x78, 61 == 0x7A
//i2cLcdFlip = 1 // Rotate i2c LCD screen 180 degrees
//i2cLcdOnContrast = 127 // Allows you to adjust the contrast on your i2c LCD screen
//i2cScan = 1 // scan i2c bus and display addresses on screen
i2cLcdUseCBMChar = 1 // set it to 1 to use CBM font on LCD. Small but fun !
//QuickBoot = 0 // faster startup
//ShowOptions = 0 // display some options on startup screen
//IgnoreReset = 0
// You can remap the physical button functions
// numbers correspond to the standard board layout
//buttonEnter = 1
//buttonUp = 2
//buttonDown = 3
//buttonBack = 4
//buttonInsert = 5
//ROTARY:
//
// KY-040 Rotary Encoder Support
//
// If you would like to use a KY-040 Rotary Encoder for browse menu up/down
// and select, you can enable it here. Connect as follows:
//
// GPIO 22 - Menu up - Encoder pin A (CLK)
// GPIO 23 - Menu down - Encoder pin B (DT)
// GPIO 27 - Enter/Select - Encoder pushbutton (SW)
//
// Using an encoder is incompatible with the button remapping. You must
// use the default values of Enter=1, Up=2, Down=3, Back=4 and Insert=5.
//
// This has only been tested using a Raspberry Pi 3. Earlier models may
// or may not work as expected!
//
// Please see dmRotary.h for full implementation details.
//
// Updated to address issue #185 and allow for inversion of rotary operation
// for certain encoders. - 08/13/2020 by Geo...
//
//RotaryEncoderEnable = 1
//RotaryEncoderInvert = 1
// This option will display the temperature of the Pi's CPU.
// It should be about 52 C anything above 65 C is bad and there is something wrong with your hardware
DisplayTemperature = 1
// Displays a visualization of the data of a disk image on the Pi
DisplayTracks = 1`
Good evening. It's me again. After several tests I can now say that the chargen font is not displayed on the PI1541 RPi2b. TrackDisplay and Temperature do not work either. The same options.txt in the RPi3 works fine.
`// Sample options.txt configuration file for Pi1541
// If you would like to change the drive number then specify it here (8 is the default) deviceID = 9
// If you are using the split line hardware option (ie Option B) then you need to specify this option splitIECLines = 1 // If you are using some type of hardware that requires the lines to be inverted then specify these options here //invertIECInputs = 1 //If you are using a 7407 //invertIECOutputs = 0
// If you are using the Pi's composite video out then these options allow you to experiment with the display resolution //ScreenWidth = 512 //ScreenHeight = 384
// By default Pi1541 will search the root of the SD card for a ROM file and use this for ROM1. // The first file found with either of the following names will be used; d1541.rom, dos1541, d1541II, Jiffy.bin // You can override the default ROM1 by specifying it here //ROM1 = YourDefaultRom // You can specify additional ROMS here (up to 7) // You can then use the function keys (F1-F7) on the keyboard to change which one you would like to use (only in browse mode and not in emulation mode) // You can also use the buttons to swap ROMs by holding down button 1 and pressing one other buttons 2-5 // .LST files can also specify one of these ROMS that will automatically be selected when the LST file is loaded. //ROM2 = Jiffy.bin //ROM3 = d1541II
// Reference you 1581 ROM here //ROM1581 = 1581-rom.318045-02.bin //ROM1581 = JiffyDOS_1581.bin
// The rate (in seconds) a long selection is scrolled scrollHighlightRate = 0.09
// Enable RAMBoard emulation - 8k drive RAM expansion at 0x8000 //RAMBOard = 1
ChargenFont = chargen // 8 bit font file
// If using CBMFileBrowser then it is best to specify this option. When the computer resets the Pi will always revert back to the root folder ready to load CBMFileBrowser again. OnResetChangeToStartingFolder = 1
// If you use FB64 (CBMFileBrowser) and want to use a fast loader cartridge (AR6, EFL, FC3) to load it then use this option to automatically mount it. //AutoMountImage = fb.d64 // You MUST have a disk image in \1541 with this filename // If you use FB64 (CBMFileBrowser) and want Pi1541 to send all file names as lower case. //LowercaseBrowseModeFilenames = 1
// If you are using a FB128 in 128 mode you can get FB128 to auto boot using this option //AutoBootFB128 = 1
// If you are using a 128 you can auto boot anything using this option // This over-rides AutoBootFB128 //128BootSectorName = bootsect.128
// If you would ever like to disable browse mode completely you can do so here //DisableSD2IECCommands = 1
// This option displays the IEC bus activity on the bottom of the Pi's screen GraphIEC = 1
// If you have hardware with a peizo buzzer (the type without a generator) then you can use this option to hear the head step SoundOnGPIO = 1 SoundOnGPIODuration = 100 // Length of buzz in micro seconds SoundOnGPIOFreq = 200 // Frequency of buzz in Hz
// You can create 320x200 PNG files with the same name as your disk images. With this option turned on they will be displayed on the Pi's screen. //DisplayPNGIcons = 1
// If you would like to specify what file will be loaded by LOAD"*" in browse mode then specify it here //StarFileName = somefile
// Alt-N creates a new disk image. // Names are formed automatically as autoname001.d64, autoname002.d64 etc... // change the base of the filename here //AutoBaseName = autoname // By default Alt-N creates a new D64 disk image. // If you rather it create a G64 then use this option. //NewDiskType = g64
// If you are using a LCD screen then specify it here LCDName = ssd1306_128x64 //LCDName = ssd1306_128x32 //LCDName = sh1106_128x64 // If you are using a LCD screen and you would like PageUp and PageDown keys to work with it (rather than the HDMI screen) then specify this option //KeyboardBrowseLCDScreen = 1
// change startup logo on oled - 1541ii or 1541classic //LcdLogoName = 1541ii //LcdLogoName = 1541classic //LcdLogoName = customfile.raw
// If you are using I2C LCD you can optionally change what pins it is connected to. // (defaults to 0 for non-split lines (Option A) or 1 for split lines (Option B)) //i2cBusMaster = 0 //SDA - pin 27 SCL - pin 28 i2cBusMaster = 1 //SDA - pin 3 SCL - pin 5 //i2cLcdAddress = 60 // I2C display address in decimal and shifted. 60 == 0x78, 61 == 0x7A //i2cLcdFlip = 1 // Rotate i2c LCD screen 180 degrees //i2cLcdOnContrast = 127 // Allows you to adjust the contrast on your i2c LCD screen //i2cScan = 1 // scan i2c bus and display addresses on screen i2cLcdUseCBMChar = 1 // set it to 1 to use CBM font on LCD. Small but fun !
//QuickBoot = 0 // faster startup //ShowOptions = 0 // display some options on startup screen //IgnoreReset = 0
// You can remap the physical button functions // numbers correspond to the standard board layout //buttonEnter = 1 //buttonUp = 2 //buttonDown = 3 //buttonBack = 4 //buttonInsert = 5
//ROTARY: // // KY-040 Rotary Encoder Support // // If you would like to use a KY-040 Rotary Encoder for browse menu up/down // and select, you can enable it here. Connect as follows: // // GPIO 22 - Menu up - Encoder pin A (CLK) // GPIO 23 - Menu down - Encoder pin B (DT) // GPIO 27 - Enter/Select - Encoder pushbutton (SW) // // Using an encoder is incompatible with the button remapping. You must // use the default values of Enter=1, Up=2, Down=3, Back=4 and Insert=5. // // This has only been tested using a Raspberry Pi 3. Earlier models may // or may not work as expected! // // Please see dmRotary.h for full implementation details. // // Updated to address issue #185 and allow for inversion of rotary operation // for certain encoders. - 08/13/2020 by Geo... // //RotaryEncoderEnable = 1 //RotaryEncoderInvert = 1
// This option will display the temperature of the Pi's CPU. // It should be about 52 C anything above 65 C is bad and there is something wrong with your hardware DisplayTemperature = 1
// Displays a visualization of the data of a disk image on the Pi DisplayTracks = 1`