search

pianyu / 0xdroid

Automatically exported from code.google.com/p/0xdroid
0 stars 0 forks source link

modifying devkit8000_defconfig file causing problem #179

Open GoogleCodeExporter opened 9 years ago

GoogleCodeExporter commented 9 years ago 
My intentions is to do mux config on 40pin IO expander, turning one of the MMC2 
pin to become a GPIO that I wanted to control.

Is this ok to let the beagle stuffs inside the devkit8000_defconfig file or I 
need to disable it? My concern it will make the MUX not working.

Currently, without care the android os able to load I able to latch the IO that 
I preferred to use seeing from scope, by proceed the following to be mention 
step 1 & step2.

What steps will reproduce the problem?
1.commented/disable CONFIG_MACH_OMAP3_BEAGLE=y & 
CONFIG_SND_OMAP_SOC_OMAP3_BEAGLE=y. Even though it is a devkit8000_defconfig 
files somehow beagle feature is there!
2.or enable CONFIG_OMAP_MUX=y

What is the image version having this issue? You can see that from
"/version.txt" in the image.
Version:linux-2.6.32.9

What is the date of your image built?
Date:today

What is the expected output? What do you see instead?
after proceed with step 1 & step 2. Manage to compile kernel image without 
error. then load it to devkit8000. once done restarts, devkit8000 will load 
until the words "android". Stuck there forever.

What version of the product are you using? On what operating system?
beagle-eclair

Please provide any additional information below.

terminal printout:
Texas Instruments X-Loader 1.41
Starting OS Bootloader...

U-Boot 2009.11-00423-gb5f90cf-dirty (Mar 19 2010 - 19:16:52)

OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 DevKit8000 + LPDDR/NAND
I2C:   ready
DRAM:  128 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Die ID #7fb800040000000004036ac003007006
Net:   dm9000
Hit any key to stop autoboot:  0
No MMC card found
Unknown command 'mmcinit' - try 'help'
Booting from nand ...

NAND read: device 0 offset 0x280000, size 0x400000
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-2.6.32.9-g4fbb0d4-dirty
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2732048 Bytes =  2.6 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.32.9-g4fbb0d4-dirty (root@weichons-laptop) (gcc version 4.4.0 
(GCC) ) #14 Thu Feb 2 18:03:25 MYT 2012
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 Devkit8000
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS2,115200n8 vram=12M omapdss.def_disp=lcd 
omapfb.mode=lcd:800x480 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs init=/init 
rw rootwait
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 111360KB available (4820K code, 996K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/266/500 MHz
Reprogramming SDRC clock to 266000000 Hz
dpll3_m2_clk rate change failed: -22
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
devkit8000_twl_gpio_setup:319
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 217
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
loop: module loaded
omap2-nand driver initializing
omap2-nand: irqstatus set on cmd entry ff
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xb1 (Micron NAND 128MiB 1,8V 
16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000680000 : "Kernel"
0x000000680000-0x000008000000 : "File System"
UBI: attaching mtd4 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd4 to ubi0
UBI: MTD device name:            "File System"
UBI: MTD device size:            121 MiB
UBI: number of good PEBs:        971
UBI: number of bad PEBs:         1
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 971
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 73/38
UBI: image sequence number: 1966967770
dm9000 Ethernet Driver, V1.31
UBI: background thread "ubi_bgt0d" started, PID 431
eth0: dm9000a at c88b6000,c88ba400 IRQ 185 MAC: 02:c0:03:00:70:06 (platform 
data)
usbcore: registered new interface driver cdc_ether
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: ?
usb usb1: Manufacturer: ?
usb usb1: SerialNumber: ?
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
android init
android_probe pdata: c0512b54
android_bind
android_usb gadget: android_usb ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: ?
usb usb2: Manufacturer: ?
usb usb2: SerialNumber: ?
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
f_adb init
android_register_function adb
f_mass_storage init
android_register_function usb_mass_storage
adb_bind_config
mass_storage_bind_config
android_usb gadget: Number of LUNs=1
mice: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
ads7846 spi2.0: touchscreen, irq 187
input: ADS7846 Touchscreen as 
/devices/platform/omap2_mcspi.2/spi2.0/input/input1
input: twl4030_pwrbutton as 
/devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input2
using rtc device, twl4030_rtc, for alarms
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
twl4030_rtc twl4030_rtc: Power up reset detected.
twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
i2c /dev entries driver
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
logger: created 64K log 'log_system'
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
  No soundcards found.
oprofile: using arm/armv7
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
Console: switching to colour frame buffer device 100x30
regulator_init_complete: incomplete constraints, leaving VDAC on
twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC 
(946684800)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   122185728 bytes (119322 KiB, 116 MiB, 947 LEBs)
UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:13.
Freeing init memory: 140K
Warning: unable to open an initial console.
# enabling adb
adb_open
warning: `rild' uses 32-bit capabilities (legacy support in use)
eth0: link down
init: sys_prop: mis-match msg size recieved: -1 expected: 128

Original issue reported on code.google.com by dennisdo...@gmail.com on 2 Feb 2012 at 10:51

GoogleCodeExporter commented 9 years ago 
just tried to use back the default devkit8000_defconfig(). able to latch IO 
that I have configure. so far problem solved. but still worry about having two 
type of board beagle & devkit8000 enable in the config file, or there is 
nothing to worry about?

Original comment by dennisdo...@gmail.com on 2 Feb 2012 at 11:46