When burning a bootloader using PlatformIO, the bootloader script are mistakenly adding -P usb as the Avrdude upload port, even though the serialupdi programmer is a serial device. This is not a problem in the fuses.py script, so I simply copied the logic from there.
@valeros it would be great if you could give this a review!
platformio.ini file
```ini
[env]
platform = atmelmegaavr
framework = arduino
board = ATmega4809
; Clock frequency in [Hz]
board_build.f_cpu = 4000000L
; Oscillator type (internal or external)
board_hardware.oscillator = internal
; Arduino pinout variant
board_build.variant = 40pin-standard
; Monitor port is auto detected. Override here
;monitor_port =
monitor_speed = 9600
monitor_dtr = 0
; Run the following command to upload with this environment
; pio run -t upload
[env:Upload_UPDI]
; Upload protocol for UPDI upload
upload_protocol = serialupdi
upload_port = /dev/cu.usbserial-1410
; COM1 or COM3
upload_speed = 115200
upload_flags =
-xrtsdtr=high
; run the following command to set fuses
; pio run -e fuses_bootloader -t fuses
; run the following command to set fuses + burn bootloader
; pio run -e fuses_bootloader -t bootloader -F -v
[env:fuses_bootloader]
; Inherit upload settings from the Upload_UPDI environment
extends = env:Upload_UPDI
; Hardware settings
board_hardware.bod = 2.6v
board_hardware.eesave = yes
board_hardware.uart = uart0
board_hardware.rstpin = reset
```
pio run -t bootloader -e fuses_bootloader -v
Processing fuses_bootloader (extends: env:Upload_UPDI; board_hardware.bod: 2.6v; board_hardware.eesave: yes; board_hardware.uart: uart0; board_hardware.rstpin: reset; upload_protocol: serialupdi; upload_port: /dev/cu.usbserial-1410; upload_speed: 115200; upload_flags: -xrtsdtr=high; platform: atmelmegaavr; framework: arduino; board: ATmega4809; board_build.f_cpu: 4000000L; board_hardware.oscillator: internal; board_build.variant: 40pin-standard; monitor_speed: 9600; monitor_dtr: 0)
--------------------------------------------------------------------------------------------------------------------------------------------------
CONFIGURATION: https://docs.platformio.org/page/boards/atmelmegaavr/ATmega4809.html
PLATFORM: Atmel megaAVR (1.9.0) > ATmega4809
HARDWARE: ATMEGA4809 4MHz, 6KB RAM, 48KB Flash
PACKAGES:
- framework-arduino-megaavr-megacorex @ 1.1.2
- tool-avrdude @ 1.70100.0 (7.1.0)
- toolchain-atmelavr @ 1.70300.191015 (7.3.0)
LDF: Library Dependency Finder -> https://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 11 compatible libraries
Scanning dependencies...
No dependencies
Building in release mode
TARGET CONFIGURATION:
-------------------------
Target = atmega4809
Clock speed = 4000000L
Oscillator = internal
BOD level = 2.6v
Save EEPROM = yes
Reset pin mode = reset
-------------------------
Using manually specified: /dev/cu.usbserial-1410
Selected fuses:
-------------------------
[fuse0 / wdtcfg = 0x00]
[fuse1 / bodcfg = 0x54]
[fuse2 / osccfg = 0x01]
[fuse4 / tcd0cfg = 0x00]
[fuse5 / syscfg0 = 0xC9]
[fuse6 / syscfg1 = 0x06]
[fuse7 / append = 0x00]
[fuse8 / bootend = 0x02]
[lock / lockbit = 0xC5]
-------------------------
avrdude -p atmega4809 -C /Users/hans/.platformio/packages/tool-avrdude/avrdude.conf -v -P "/dev/cu.usbserial-1410" -c serialupdi -xrtsdtr=high -Ufuse0:w:0x00:m -Ufuse1:w:0x54:m -Ufuse2:w:0x01:m -Ufuse4:w:0x00:m -Ufuse5:w:0xC9:m -Ufuse6:w:0x06:m -Ufuse7:w:0x00:m -Ufuse8:w:0x02:m -Ulock:w:0xC5:m
avrdude: Version 7.1-arduino.1
Copyright the AVRDUDE authors;
see https://github.com/avrdudes/avrdude/blob/main/AUTHORS
System wide configuration file is /Users/hans/.platformio/packages/tool-avrdude/avrdude.conf
User configuration file is /Users/hans/.avrduderc
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/cu.usbserial-1410
Using Programmer : serialupdi
AVR Part : ATmega4809
RESET disposition : dedicated
RETRY pulse : SCK
Serial program mode : yes
Parallel program mode : yes
Memory Detail :
Block Poll Page Polled
Memory Type Alias Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- -------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
fuse0 wdtcfg 0 0 0 0 no 1 1 0 0 0 0x00 0x00
fuse1 bodcfg 0 0 0 0 no 1 1 0 0 0 0x00 0x00
fuse2 osccfg 0 0 0 0 no 1 1 0 0 0 0x00 0x00
fuse4 tcd0cfg 0 0 0 0 no 1 1 0 0 0 0x00 0x00
fuse5 syscfg0 0 0 0 0 no 1 1 0 0 0 0x00 0x00
fuse6 syscfg1 0 0 0 0 no 1 1 0 0 0 0x00 0x00
fuse7 append 0 0 0 0 no 1 1 0 0 0 0x00 0x00
fuse8 bootend 0 0 0 0 no 1 1 0 0 0 0x00 0x00
fuses 0 0 0 0 no 9 10 0 0 0 0x00 0x00
lock 0 0 0 0 no 1 1 0 0 0 0x00 0x00
tempsense 0 0 0 0 no 2 1 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 1 0 0 0 0x00 0x00
prodsig 0 0 0 0 no 61 61 0 0 0 0x00 0x00
sernum 0 0 0 0 no 10 1 0 0 0 0x00 0x00
osccal16 0 0 0 0 no 2 1 0 0 0 0x00 0x00
osccal20 0 0 0 0 no 2 1 0 0 0 0x00 0x00
osc16err 0 0 0 0 no 2 1 0 0 0 0x00 0x00
osc20err 0 0 0 0 no 2 1 0 0 0 0x00 0x00
data 0 0 0 0 no 0 1 0 0 0 0x00 0x00
userrow usersig 0 0 0 0 no 64 64 0 0 0 0x00 0x00
eeprom 0 0 0 0 no 256 64 0 0 0 0x00 0x00
flash 0 0 0 0 no 49152 128 0 0 0 0x00 0x00
Programmer Type : serialupdi
Description : SerialUPDI
avrdude serialupdi_initialize() warning: forcing serial DTR/RTS handshake lines HIGH
avrdude: NVM type 0: 16-bit, page oriented write
avrdude: entering NVM programming mode
avrdude: AVR device initialized and ready to accept instructions
avrdude: device signature = 0x1e9651 (probably m4809)
avrdude: reading input file 0x00 for fuse0/wdtcfg
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte fuse0/wdtcfg ...
avrdude: 1 byte of fuse0/wdtcfg written
avrdude: verifying fuse0/wdtcfg memory against 0x00
avrdude: 1 byte of fuse0/wdtcfg verified
avrdude: reading input file 0x54 for fuse1/bodcfg
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte fuse1/bodcfg ...
avrdude: 1 byte of fuse1/bodcfg written
avrdude: verifying fuse1/bodcfg memory against 0x54
avrdude: 1 byte of fuse1/bodcfg verified
avrdude: reading input file 0x01 for fuse2/osccfg
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte fuse2/osccfg ...
avrdude: 1 byte of fuse2/osccfg written
avrdude: verifying fuse2/osccfg memory against 0x01
avrdude: 1 byte of fuse2/osccfg verified
avrdude: reading input file 0x00 for fuse4/tcd0cfg
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte fuse4/tcd0cfg ...
avrdude: 1 byte of fuse4/tcd0cfg written
avrdude: verifying fuse4/tcd0cfg memory against 0x00
avrdude: 1 byte of fuse4/tcd0cfg verified
avrdude: reading input file 0xC9 for fuse5/syscfg0
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte fuse5/syscfg0 ...
avrdude: 1 byte of fuse5/syscfg0 written
avrdude: verifying fuse5/syscfg0 memory against 0xC9
avrdude: 1 byte of fuse5/syscfg0 verified
avrdude: reading input file 0x06 for fuse6/syscfg1
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte fuse6/syscfg1 ...
avrdude: 1 byte of fuse6/syscfg1 written
avrdude: verifying fuse6/syscfg1 memory against 0x06
avrdude: 1 byte of fuse6/syscfg1 verified
avrdude: reading input file 0x00 for fuse7/append
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte fuse7/append ...
avrdude: 1 byte of fuse7/append written
avrdude: verifying fuse7/append memory against 0x00
avrdude: 1 byte of fuse7/append verified
avrdude: reading input file 0x02 for fuse8/bootend
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte fuse8/bootend ...
avrdude: 1 byte of fuse8/bootend written
avrdude: verifying fuse8/bootend memory against 0x02
avrdude: 1 byte of fuse8/bootend verified
avrdude: reading input file 0xC5 for lock
with 1 byte in 1 section within [0, 0]
avrdude: writing 1 byte lock ...
avrdude: 1 byte of lock written
avrdude: verifying lock memory against 0xC5
avrdude: 1 byte of lock verified
avrdude: leaving NVM programming mode
avrdude serialupdi_close() warning: releasing DTR/RTS handshake lines
avrdude done. Thank you.
avrdude -p atmega4809 -C /Users/hans/.platformio/packages/tool-avrdude/avrdude.conf -P usb -c serialupdi -xrtsdtr=high -U flash:w:/Users/hans/.platformio/packages/framework-arduino-megaavr-megacorex/bootloaders/optiboot/bootloaders/mega0/115200/Optiboot_mega0_UART0_DEF_115200_A7.hex:i
avrdude OS error: cannot open port usb: No such file or directory
avrdude error: unable to open programmer serialupdi on port usb
avrdude done. Thank you.
*** [bootloader] Error 1
valeros
commented
9 months ago
First reported here: https://github.com/MCUdude/MegaCoreX/issues/193
When burning a bootloader using PlatformIO, the bootloader script are mistakenly adding
-P usbas the Avrdude upload port, even though the serialupdi programmer is a serial device. This is not a problem in the fuses.py script, so I simply copied the logic from there.@valeros it would be great if you could give this a review!
platformio.ini file
```ini [env] platform = atmelmegaavr framework = arduino board = ATmega4809 ; Clock frequency in [Hz] board_build.f_cpu = 4000000L ; Oscillator type (internal or external) board_hardware.oscillator = internal ; Arduino pinout variant board_build.variant = 40pin-standard ; Monitor port is auto detected. Override here ;monitor_port = monitor_speed = 9600 monitor_dtr = 0 ; Run the following command to upload with this environment ; pio run -t upload [env:Upload_UPDI] ; Upload protocol for UPDI upload upload_protocol = serialupdi upload_port = /dev/cu.usbserial-1410 ; COM1 or COM3 upload_speed = 115200 upload_flags = -xrtsdtr=high ; run the following command to set fuses ; pio run -e fuses_bootloader -t fuses ; run the following command to set fuses + burn bootloader ; pio run -e fuses_bootloader -t bootloader -F -v [env:fuses_bootloader] ; Inherit upload settings from the Upload_UPDI environment extends = env:Upload_UPDI ; Hardware settings board_hardware.bod = 2.6v board_hardware.eesave = yes board_hardware.uart = uart0 board_hardware.rstpin = reset ```