search

pr0v3rbs / FirmAE

Towards Large-Scale Emulation of IoT Firmware for Dynamic Analysis
MIT License
667 stars 121 forks source link

Error:None false false -1 -1 #64

Open SaraWonder opened 1 year ago

SaraWonder commented 1 year ago

Hello. i Have problem emulate Firmware and access it web panel but i get this error

`[] 18NEW.tgz emulation start!!! [] extract done!!! [] get architecture done!!! mke2fs 1.44.1 (24-Mar-2018) mknod: /dev/null: File exists mknod: /dev/zero: File exists mknod: /dev/console: File exists e2fsck 1.44.1 (24-Mar-2018) [] infer network start!!!

[IID] 9 [MODE] run [+] Network reachable on 192.168.0.1! Creating TAP device tap9_0... Set 'tap9_0' persistent and owned by uid 0 Bringing up TAP device... Starting emulation of firmware... None false false -1 -1`

h00die-gr3y commented 1 year ago

@SaraWonder I have the same problem with another firmware and I found a fix for it. Just have a look if below works for you too.

First step, run you firmware with the debug option ./run.sh -d <brand> <firmware> Let it run until you reach the debug menu. This might take a while, but you can speed this up by setting the arbitrary option FIRMAE_ETC in firmae.config to false (however, not necessary to make below work).

[IID] 1
[MODE] debug
[+] Network reachable on 192.168.0.1!
[+] Run debug!
Creating TAP device tap1_0...
Set 'tap1_0' persistent and owned by uid 0
Bringing up TAP device...
Starting emulation of firmware... None false false -1 -1
/root/FirmAE/./debug.py:7: DeprecationWarning: 'telnetlib' is deprecated and slated for removal in Python 3.13
  import telnetlib
[*] firmware - X5000R_V9.1.0u.6118_B20201102
[*] IP - 192.168.0.1
[*] connecting to netcat (192.168.0.1:31337)
[-] failed to connect netcat
------------------------------
|       FirmAE Debugger      |
------------------------------
1. connect to socat
2. connect to shell
3. tcpdump
4. run gdbserver
5. file transfer
6. exit

Netcat will not work because your network is not properly configured, but you can use option 1. connect to socat to access your running firmware and run below commands to check your network configuration.

>1
/ # brctl show
brctl show
bridge name bridge id       STP enabled interfaces
br0     8000.525400123458   yes     eth2
/ # ifconfig -a
ifconfig -a
br0       Link encap:Ethernet  HWaddr 52:54:00:12:34:56
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 52:54:00:12:34:56
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth1      Link encap:Ethernet  HWaddr 52:54:00:12:34:57
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth2      Link encap:Ethernet  HWaddr 52:54:00:12:34:58
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:33 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:1980 (1.9 KiB)

eth3      Link encap:Ethernet  HWaddr 52:54:00:12:34:59
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

ip6tnl0   Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
          NOARP  MTU:1452  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

tunl0     Link encap:UNSPEC  HWaddr 00-00-00-00-D4-7F-2C-6A-00-00-00-00-00-00-00-00
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

/ #

In my case, there were two issues, first of all the bridge command showed eth2 instead eth0 and br0 did not have any IP configured. Your configuration might be a bit different. Sometimes you see a brtrunk interface instead of br0. Anyhow to fix this, run the following commands below and hopefully your firmware will be accessible from the host.

/ # brctl addif br0 eth0
brctl addif br0 eth0
/ # brctl show
brctl show
bridge name bridge id       STP enabled interfaces
br0     8000.525400123456   yes     eth2
                            eth0
/ # ifconfig eth0 up
ifconfig eth0 up
/ # ifconfig -a
ifconfig -a
br0       Link encap:Ethernet  HWaddr 52:54:00:12:34:56
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 52:54:00:12:34:56
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:151 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:9206 (8.9 KiB)  TX bytes:240 (240.0 B)

eth1      Link encap:Ethernet  HWaddr 52:54:00:12:34:57
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth2      Link encap:Ethernet  HWaddr 52:54:00:12:34:58
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:53 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:3180 (3.1 KiB)

eth3      Link encap:Ethernet  HWaddr 52:54:00:12:34:59
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

ip6tnl0   Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
          NOARP  MTU:1452  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

tunl0     Link encap:UNSPEC  HWaddr 00-00-00-00-E6-7F-FC-FF-00-00-00-00-00-00-00-00
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

/ # ifconfig br0 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255
ifconfig br0 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255
/ #

You should now be able to ping the network address 192.168.0.1 from your host and run a nmap command to check the services.


# ping 192.168.0.1
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=8.92 ms
64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=2.38 ms
^C
--- 192.168.0.1 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 2.384/5.650/8.916/3.266 ms
# nmap 192.168.0.1
Starting Nmap 7.94 ( https://nmap.org ) at 2023-09-12 17:44 UTC
Nmap scan report for 192.168.0.1
Host is up (0.011s latency).
Not shown: 997 closed tcp ports (reset)
PORT     STATE    SERVICE
23/tcp   filtered telnet
80/tcp   filtered http
8080/tcp filtered http-proxy
MAC Address: 52:54:00:12:34:56 (QEMU virtual NIC)

Nmap done: 1 IP address (1 host up) scanned in 1.78 seconds
pr0v3rbs commented 11 months ago

@SaraWonder It looks like the target firmware failed on emulation. We need to investigate the system.

@h00die-gr3y Thank you so much for your investigation, I hope your guide will help the @SaraWonder.