search

protonmaster / minimosd-extra

Automatically exported from code.google.com/p/minimosd-extra
0 stars 0 forks source link

OSD not displaying info without telemetry link with computer #108

Open GoogleCodeExporter opened 9 years ago

GoogleCodeExporter commented 9 years ago 
What steps will reproduce the problem?
1. If I plug in the OSD and copter without a link to APM Planner 2.0
2.
3.

What is the expected output? What do you see instead?
     I expect to see my location, battery, heading, etc...  If I establish a link everything works fine. I can even establish a link and then disconnect from the planner and the OSD works great. If I try to arm and use it without establishing a telemetry link for it will not work.

What version of the product are you using? On what operating system?

APM Planner 2.0
Current up to date copter firmware
MinimOSD extra 2.4 r702 firmware

Please provide any additional information below.

Original issue reported on code.google.com by twstee...@gmail.com on 4 Dec 2014 at 2:31

GoogleCodeExporter commented 9 years ago 
There is no interaction between MinimOsd and Mission or APM Planner. I can help 
if you tell me how you power your APM and connection between APM and MinimOSD. 
Do you have 3DR Telemetery?

Original comment by osiarbay...@gmail.com on 9 Dec 2014 at 4:24

GoogleCodeExporter commented 9 years ago 
I am powered the apm by the current sensor that came in the set. I am using 
telemetry radios and use the cable that came with the kit as well. 

It is plugged into the telemetry port on the flight controller and then y's off 
to the telemetry radio and osd. The osd is only connected with 3 cables, power, 
ground, and rx.

Original comment by twstee...@gmail.com on 10 Dec 2014 at 12:48

GoogleCodeExporter commented 9 years ago 
tried a bunch of stuff again tonight. if I arm the copter without the
telemetry radios hooked up...

-no gps coordinates

-no battery information

-no osd pannel switching via my channel 8

-no indication of number of satilites locked

-system warning messages of no GPS fix and battery low

The artificial horizon works as does the rssi, tilt degrees, and heading.

Just can't seem to figure out why some data displays but not all!

-Todd

Original comment by twstee...@gmail.com on 10 Dec 2014 at 5:55

GoogleCodeExporter commented 9 years ago 
Did you enable OSD from Mission Planner?

Original comment by osiarbay...@gmail.com on 10 Dec 2014 at 5:33

GoogleCodeExporter commented 9 years ago 
Yes, I have clicked that button countless times!

Original comment by twstee...@gmail.com on 10 Dec 2014 at 7:39

GoogleCodeExporter commented 9 years ago 
I think you should also connect the Tx wire between APM and minimOSD when 
telemetry is not connected. The 3-wire connection between minimOSD and APM is a 
"slave" connection in which the Tx is sent to the APM from the telemetry radio, 
when telemetry is connected.

Original comment by emanuel....@gmail.com on 10 Dec 2014 at 11:35

GoogleCodeExporter commented 9 years ago 
Do you mean the TX on the OSD and then connect that to the APM? So all 4
wires will be hooked up?

-Todd

Original comment by twstee...@gmail.com on 11 Dec 2014 at 2:38

GoogleCodeExporter commented 9 years ago 
I am using Bluetooth telemetry, and connected MinimOsd to UART0 header. 
Everything works fine, maybe this will help with your situation.

http://copter.ardupilot.com/wp-content/uploads/sites/2/2012/12/apm.jpg

Original comment by osiarbay...@gmail.com on 11 Dec 2014 at 5:34