Closed n1gp closed 8 months ago
I have another update for this PR, I'll get that in tomorrow. I intended on copying all of the filter bits and then overlay the TX ANT bits. I just overlayed the ANT bits which is enough for testing.
That should do it.
cheers Rick, no time to do any testing here unfortunately at the moment, but have merged this
Hi everyone
I’ve committed the new G2 firmware and P2app. These now correctly take the TX antenna from the new data bits in the protocol 2 high priority message, and RX antenna from the pre-existing bytes.
Tested with this temporary version of Thetis, that sets the new TX antenna bits.
When used with legacy version of Thetis, p2app detects that no TX bits are set and uses the “old” antenna bits (which at start of TX will begin on the RX setting, then change over).
I haven’t tested with the CW keyer yet but the message is being correctly decoded and processed through into the new firmware.
So from both an Orion mk 2 and Saturn perspective, the “CW leakage into RX antenna” should now be resolved.
Laurence Barker G8NJJ
@.***
From: Richie @.> Sent: Wednesday, January 10, 2024 3:42 AM To: ramdor/Thetis @.> Cc: Subscribed @.***> Subject: Re: [ramdor/Thetis] Adding fix for 'Investigate power (CW) appearing on rx only ports #228' (PR #381)
cheers Rick, no time to do any testing here unfortunately at the moment, but have merged this
— Reply to this email directly, view it on GitHub https://github.com/ramdor/Thetis/pull/381#issuecomment-1884141786 , or unsubscribe https://github.com/notifications/unsubscribe-auth/AEXTXZ54OIVEAKX27BIPULLYNYEYLAVCNFSM6AAAAABBRMIKM2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQOBUGE2DCNZYGY . You are receiving this because you are subscribed to this thread. https://github.com/notifications/beacon/AEXTXZYW3LPCXJ7YNGGLIOTYNYEYLA5CNFSM6AAAAABBRMIKM2WGG33NNVSW45C7OR4XAZNMJFZXG5LFINXW23LFNZ2KUY3PNVWWK3TUL5UWJTTQJW4NU.gif Message ID: @. @.> >
Committed it where?
All the Saturn firmware and software is in my github repository:
github.com/laurencebarker/Saturn
Laurence Barker G8NJJ
@.***
From: Michael Black @.> Sent: Wednesday, January 10, 2024 9:02 PM To: ramdor/Thetis @.> Cc: Laurence Barker @.>; Comment @.> Subject: Re: [ramdor/Thetis] Adding fix for 'Investigate power (CW) appearing on rx only ports #228' (PR #381)
Committed it where?
— Reply to this email directly, view it on GitHub https://github.com/ramdor/Thetis/pull/381#issuecomment-1885724636 , or unsubscribe https://github.com/notifications/unsubscribe-auth/AEXTXZ4TEEAGYR42UC5OEBTYN36TFAVCNFSM6AAAAABBRMIKM2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQOBVG4ZDINRTGY . You are receiving this because you commented. https://github.com/notifications/beacon/AEXTXZ53DULWSIXWMR4MOPDYN36TFA5CNFSM6AAAAABBRMIKM2WGG33NNVSW45C7OR4XAZNMJFZXG5LFINXW23LFNZ2KUY3PNVWWK3TUL5UWJTTQMXP5Y.gif Message ID: @. @.> >
this adds sending the selected ANT1-3 bits through the High Priority Packet. New SDR firmware will use this to decide which ANT to select BEFORE going into TX. Older SDR firmware will still operate the same selecting the ANT after going to TX.