DRAM: 64 MiB
Check Flash Memory Controller v100 ... Found
SPI Nor(cs 0) ID: 0xc2 0x20 0x18
Block:64KB Chip:16MB Name:"MX25L128XX"
SPI Nor total size: 16MB
MMC:
EMMC/MMC/SD controller initialization.
MMC/SD Card:
MID: 0x3
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7580M Bytes (High Capacity)
Name: "SL08G"
Chip Type: SD
Version: 2.0
Speed: 50000000Hz
Bus Width: 4bit
Boot Addr: 0 Bytes
In: serial
Out: serial
Err: serial
device name mmc!
Interface: MMC
Device 0: Vendor: Man 035344 Snr 8564417a Rev: 8.0 Prod: SL08G
Type: Removable Hard Disk
Capacity: 7580.0 MB = 7.4 GB (15523840 x 512)
Partition 1: Filesystem: FAT32 "NO NAME "
reading ezviz.dav
Find 1 packet
file_pos is 0x81000098
app.img checksum is fail
checksum is 682704412, but file original checksum is 681896039
update file startOffset = 152
update file len = 5300224
update_single_file fail
Net: No ethernet found.
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit Ctrl+u to stop autoboot: 0
load kernel to 0x80007fc0 ...
check backup upgrade flag
Done!
Booting kernel from Legacy Image at 80007fc0 ...
Image Name: Linux-3.4.35
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2445872 Bytes = 2.3 MiB
Load Address: 80008000
Entry Point: 80008000
XIP Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
init started: BusyBox v1.22.1 (2017-08-04 12:25:23 CST)
ifconfig: SIOCGIFFLAGS: No such device
mount: mounting /dev/mtdblock5 on /mnt failed: Invalid argument
APP partition is broken!
cp: can't stat '/mnt/initrun.sh': No such file or directory
No initrun.sh on flash!
umount: can't umount /mnt: Invalid argument
Not find initrun.sh!
/ #
See in bold below:
System startup
U-Boot 2010.06-19073 (Jun 15 2017 - 14:11:13)
DRAM: 64 MiB Check Flash Memory Controller v100 ... Found SPI Nor(cs 0) ID: 0xc2 0x20 0x18 Block:64KB Chip:16MB Name:"MX25L128XX" SPI Nor total size: 16MB MMC: EMMC/MMC/SD controller initialization. MMC/SD Card: MID: 0x3 Read Block: 512 Bytes Write Block: 512 Bytes Chip Size: 7580M Bytes (High Capacity) Name: "SL08G" Chip Type: SD Version: 2.0 Speed: 50000000Hz Bus Width: 4bit Boot Addr: 0 Bytes In: serial Out: serial Err: serial device name mmc! Interface: MMC Device 0: Vendor: Man 035344 Snr 8564417a Rev: 8.0 Prod: SL08G Type: Removable Hard Disk Capacity: 7580.0 MB = 7.4 GB (15523840 x 512) Partition 1: Filesystem: FAT32 "NO NAME " reading ezviz.dav Find 1 packet file_pos is 0x81000098 app.img checksum is fail checksum is 682704412, but file original checksum is 681896039 update file startOffset = 152 update file len = 5300224 update_single_file fail Net: No ethernet found. (Re)start USB... USB: scanning bus for devices... 1 USB Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit Ctrl+u to stop autoboot: 0 load kernel to 0x80007fc0 ... check backup upgrade flag Done! Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.4.35 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2445872 Bytes = 2.3 MiB Load Address: 80008000 Entry Point: 80008000 XIP Kernel Image ... OK OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel. init started: BusyBox v1.22.1 (2017-08-04 12:25:23 CST) ifconfig: SIOCGIFFLAGS: No such device mount: mounting /dev/mtdblock5 on /mnt failed: Invalid argument APP partition is broken! cp: can't stat '/mnt/initrun.sh': No such file or directory No initrun.sh on flash! umount: can't umount /mnt: Invalid argument Not find initrun.sh! / #