search

retro98boy / tn3399-v3-linux

18 stars 3 forks source link

写入EMMC之后不能启动 #1

Closed dicsonpan closed 2 years ago

dicsonpan commented 2 years ago

你好，通过数据线，在MaskRom下把img写入到tn3399_v3这个板子的EMMC中，但启动之后一直黑屏，不知道我是不是操作有误？我的操作是

  1. 按着Recovery键上电，数据线连接电脑，输入rkdeveltool ld，确认板子已经进入MaskRom模式
  2. 运行 rkdeveloptool db ./rk3399_loader_v1.24.126.bin 刷入BootLoader
  3. 运行 rkdeveloptool wl 0x0 ./Manjaro-ARM-minimal-tn3399_v3-22.02.img 刷入ROM
  4. 重启，一直黑屏
retro98boy commented 2 years ago

你好，通过数据线，在MaskRom下把img写入到tn3399_v3这个板子的EMMC中，但启动之后一直黑屏，不知道我是不是操作有误？我的操作是

  1. 按着Recovery键上电，数据线连接电脑，输入rkdeveltool ld，确认板子已经进入MaskRom模式
  2. 运行 rkdeveloptool db ./rk3399_loader_v1.24.126.bin 刷入BootLoader
  3. 运行 rkdeveloptool wl 0x0 ./Manjaro-ARM-minimal-tn3399_v3-22.02.img 刷入ROM
  4. 重启，一直黑屏

有usb转uart线吗？能不能看下串口的打印消息？

dicsonpan commented 2 years ago

测试了一下，发现只要一开机，就自动进入MaskRom模式，进入MaskRom模式的话，串口是没有消息显示的。是不是rk3399_loader_v1.24.126.bin这个文件不合适？

retro98boy commented 2 years ago

测试了一下，发现只要一开机，就自动进入MaskRom模式，进入MaskRom模式的话，串口是没有消息显示的。是不是rk3399_loader_v1.24.126.bin这个文件不合适？

测试了一下，发现只要一开机，就自动进入MaskRom模式，进入MaskRom模式的话，串口是没有消息显示的。是不是rk3399_loader_v1.24.126.bin这个文件不合适？

应该不会，不过我上传了我用的mini loader blob，你可以试试。 开机就maskrom，那说明cpu没从eMMC或TF卡找到u-boot，难不成上传的镜像没烧录u-boot？你可以去我另一个库下载编译好的u-boot，再烧录到manjaro的img试试，sudo dd if=xxxx of=xxxx seek=64 conv=notrunc

retro98boy commented 2 years ago

测试了一下，发现只要一开机，就自动进入MaskRom模式，进入MaskRom模式的话，串口是没有消息显示的。是不是rk3399_loader_v1.24.126.bin这个文件不合适？

手上有TF卡没，有的话，直接把img刻录到TF卡上，插上板子开机看看？

dicsonpan commented 2 years ago

用etcher刻录了tf卡，然后插到板子上开机，依然是进入MaskRom模式

retro98boy commented 2 years ago

用etcher刻录了tf卡，然后插到板子上开机，依然是进入MaskRom模式

被隔离中没板子无法测试镜像，你把u-boot刻录到TF卡上，再插上开机试试？看还会不会直接进maskrom模式。https://github.com/retro98boy/u-boot-bin-tn3399_v3

dicsonpan commented 2 years ago

测试了一下，发现只要一开机，就自动进入MaskRom模式，进入MaskRom模式的话，串口是没有消息显示的。是不是rk3399_loader_v1.24.126.bin这个文件不合适？

测试了一下，发现只要一开机，就自动进入MaskRom模式，进入MaskRom模式的话，串口是没有消息显示的。是不是rk3399_loader_v1.24.126.bin这个文件不合适？

应该不会，不过我上传了我用的mini loader blob，你可以试试。 开机就maskrom，那说明cpu没从eMMC或TF卡找到u-boot，难不成上传的镜像没烧录u-boot？你可以去我另一个库下载编译好的u-boot，再烧录到manjaro的img试试，sudo dd if=xxxx of=xxxx seek=64 conv=notrunc

上传你的mini loader blob的时候，出现 Error: failed to stat config.ini, err=2 这个错误，上传rk3399_loader_v1.24.126.bin的时候也有，只是之前没有留意。估计还是BootLoader的问题

dicsonpan commented 2 years ago

用etcher刻录了tf卡，然后插到板子上开机，依然是进入MaskRom模式

被隔离中没板子无法测试镜像，你把u-boot刻录到TF卡上，再插上开机试试？看还会不会直接进maskrom模式。https://github.com/retro98boy/u-boot-bin-tn3399_v3 你在上海是吧？Me too

retro98boy commented 2 years ago

那个rk3399_loaderxxxx只是maskrom模式下临时用来升级固件的，不是bootloader。刷好系统后每次开机执行的不是它，u-boot才是每次开机执行的bootloader

retro98boy commented 2 years ago

测试了一下，发现只要一开机，就自动进入MaskRom模式，进入MaskRom模式的话，串口是没有消息显示的。是不是rk3399_loader_v1.24.126.bin这个文件不合适？

测试了一下，发现只要一开机，就自动进入MaskRom模式，进入MaskRom模式的话，串口是没有消息显示的。是不是rk3399_loader_v1.24.126.bin这个文件不合适？

应该不会，不过我上传了我用的mini loader blob，你可以试试。 开机就maskrom，那说明cpu没从eMMC或TF卡找到u-boot，难不成上传的镜像没烧录u-boot？你可以去我另一个库下载编译好的u-boot，再烧录到manjaro的img试试，sudo dd if=xxxx of=xxxx seek=64 conv=notrunc

上传你的mini loader blob的时候，出现 Error: failed to stat config.ini, err=2 这个错误，上传rk3399_loader_v1.24.126.bin的时候也有，只是之前没有留意。估计还是BootLoader的问题

那个rk3399_loaderxxxx只是maskrom模式下临时用来升级固件的，不是bootloader。刷好系统后每次开机执行的不是它，u-boot才是每次开机执行的bootloader

dicsonpan commented 2 years ago

用etcher刻录了tf卡，然后插到板子上开机，依然是进入MaskRom模式

被隔离中没板子无法测试镜像，你把u-boot刻录到TF卡上，再插上开机试试？看还会不会直接进maskrom模式。https://github.com/retro98boy/u-boot-bin-tn3399_v3

只是单独把这个u-boot刻录到tf卡上再插上去开机，还是会直接进入MaskRom模式。。

retro98boy commented 2 years ago

？？？？刻录命令？

retro98boy commented 2 years ago

用etcher刻录了tf卡，然后插到板子上开机，依然是进入MaskRom模式

被隔离中没板子无法测试镜像，你把u-boot刻录到TF卡上，再插上开机试试？看还会不会直接进maskrom模式。https://github.com/retro98boy/u-boot-bin-tn3399_v3

只是单独把这个u-boot刻录到tf卡上再插上去开机，还是会直接进入MaskRom模式。。

？？？？刻录命令？

dicsonpan commented 2 years ago

用etcher刻录了tf卡，然后插到板子上开机，依然是进入MaskRom模式

被隔离中没板子无法测试镜像，你把u-boot刻录到TF卡上，再插上开机试试？看还会不会直接进maskrom模式。https://github.com/retro98boy/u-boot-bin-tn3399_v3

只是单独把这个u-boot刻录到tf卡上再插上去开机，还是会直接进入MaskRom模式。。

？？？？刻录命令？

我用etcher直接把 u-boot-tn3399_v3.bin 刻录到tf卡的。。我不清楚怎么把这个u-boot烧录到Manjaro-ARM-minimal-tn3399_v3-22.02.img文件里边

retro98boy commented 2 years ago

用etcher刻录了tf卡，然后插到板子上开机，依然是进入MaskRom模式

被隔离中没板子无法测试镜像，你把u-boot刻录到TF卡上，再插上开机试试？看还会不会直接进maskrom模式。https://github.com/retro98boy/u-boot-bin-tn3399_v3

只是单独把这个u-boot刻录到tf卡上再插上去开机，还是会直接进入MaskRom模式。。

？？？？刻录命令？

我用etcher直接把 u-boot-tn3399_v3.bin 刻录到tf卡的。。我不清楚怎么把这个u-boot烧录到Manjaro-ARM-minimal-tn3399_v3-22.02.img文件里边

那当然不行了，cpu会在emmc或者tf卡的32k偏移处寻找uboot，先不管那个img文件，先把uboot直接烧录到tf卡上看会不会被加载试试，把tf卡用读卡器查到电脑上 sudo dd if=./u-boot-tn3399_v3.bin of=/dev/sdb bs=1k seek=32 这里if后面接的是uboot的位置，of后面是tf卡的设备节点

如果真的是img镜像没带uboot的话，修复img镜像也很简单，img镜像就是硬盘的克隆，把img镜像当做一个虚拟的存储设备就行了，甚至还能用parted给img分区的。 sudo dd if=./u-boot-tn3399_v3.bin of=img镜像的位置 bs=1k seek=32 conv=notrunc，这样就把uboot烧录到img镜像中了，后面可以用etcher把img烧录到tf卡上开机，也能直接maskrom下载到emmc开机

dicsonpan commented 2 years ago

把 u-boot 刻录进 img 之后，再通过 rkdeveloptool 把 img 刻录进 emmc，就可以开机。但还是黑屏，串口输出一堆错误如下： U-Boot 2022.01 (Feb 16 2022 - 15:58:47 +0800)

SoC: Rockchip rk3399 Reset cause: POR Model: TN3399_V3 Board DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe310000: 2, mmc@fe320000: 1, mmc@fe330000: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment

In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: TN3399_V3 Board Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 2 ... 1 ... 0 Card did not respond to voltage select! : -110 Card did not respond to voltage select! : -110

Device 0: unknown device starting USB... Bus usb@fe380000: ehci_generic usb@fe380000: failed to get usb phy Port not available. Bus usb@fe3c0000: ehci_generic usb@fe3c0000: failed to get usb phy Port not available. Bus usb@fe800000: Failed to get PHY0 for usb@fe800000 Port not available. Bus usb@fe900000: Failed to get PHY0 for usb@fe900000 Port not available. USB is stopped. Please issue 'usb start' first. starting USB... Bus usb@fe380000: ehci_generic usb@fe380000: failed to get usb phy Port not available. Bus usb@fe3c0000: ehci_generic usb@fe3c0000: failed to get usb phy Port not available. Bus usb@fe800000: Failed to get PHY0 for usb@fe800000 Port not available. Bus usb@fe900000: Failed to get PHY0 for usb@fe900000 Port not available. ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 missing environment variable: pxeuuid Retrieving file: pxelinux.cfg/01-ca-0d-79-a9-85-6b ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/00000000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/0000000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/000000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/00000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/0000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/00 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/0 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/default-arm-rk3399-evb_rk3399 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/default-arm-rk3399 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/default-arm ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/default ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Config file not found starting USB... Bus usb@fe380000: ehci_generic usb@fe380000: failed to get usb phy Port not available. Bus usb@fe3c0000: ehci_generic usb@fe3c0000: failed to get usb phy Port not available. Bus usb@fe800000: Failed to get PHY0 for usb@fe800000 Port not available. Bus usb@fe900000: Failed to get PHY0 for usb@fe900000 Port not available. ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Invalid bus 0 (err=-19) Failed to initialize SPI flash at 0:0 (error -19) =>

先睡，明天再研究。感谢这么晚还在指导！我也在上海，解封之后请你喝酒

retro98boy commented 2 years ago

把 u-boot 刻录进 img 之后，再通过 rkdeveloptool 把 img 刻录进 emmc，就可以开机。但还是黑屏，串口输出一堆错误如下： U-Boot 2022.01 (Feb 16 2022 - 15:58:47 +0800)

SoC: Rockchip rk3399 Reset cause: POR Model: TN3399_V3 Board DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe310000: 2, mmc@fe320000: 1, mmc@fe330000: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment

In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: TN3399_V3 Board Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 2 ... 1 ... 0 Card did not respond to voltage select! : -110 Card did not respond to voltage select! : -110

Device 0: unknown device starting USB... Bus usb@fe380000: ehci_generic usb@fe380000: failed to get usb phy Port not available. Bus usb@fe3c0000: ehci_generic usb@fe3c0000: failed to get usb phy Port not available. Bus usb@fe800000: Failed to get PHY0 for usb@fe800000 Port not available. Bus usb@fe900000: Failed to get PHY0 for usb@fe900000 Port not available. USB is stopped. Please issue 'usb start' first. starting USB... Bus usb@fe380000: ehci_generic usb@fe380000: failed to get usb phy Port not available. Bus usb@fe3c0000: ehci_generic usb@fe3c0000: failed to get usb phy Port not available. Bus usb@fe800000: Failed to get PHY0 for usb@fe800000 Port not available. Bus usb@fe900000: Failed to get PHY0 for usb@fe900000 Port not available. ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 missing environment variable: pxeuuid Retrieving file: pxelinux.cfg/01-ca-0d-79-a9-85-6b ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/00000000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/0000000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/000000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/00000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/0000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/00 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/0 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/default-arm-rk3399-evb_rk3399 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/default-arm-rk3399 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/default-arm ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Retrieving file: pxelinux.cfg/default ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Config file not found starting USB... Bus usb@fe380000: ehci_generic usb@fe380000: failed to get usb phy Port not available. Bus usb@fe3c0000: ehci_generic usb@fe3c0000: failed to get usb phy Port not available. Bus usb@fe800000: Failed to get PHY0 for usb@fe800000 Port not available. Bus usb@fe900000: Failed to get PHY0 for usb@fe900000 Port not available. ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! Could not initialize PHY ethernet@fe300000 Invalid bus 0 (err=-19) Failed to initialize SPI flash at 0:0 (error -19) =>

先睡，明天再研究。感谢这么晚还在指导！我也在上海，解封之后请你喝酒

这个板子是tn3399 v3吗？tn3399好像有几个版本 要不你刷下我适配的另一个库里的batocera模拟器游戏系统？那个镜像是绝对可以用的 把那个img用etcher刻录到tf卡上就可以。 为了保证cpu从tf卡启动，而不是emmc，可以在不插tf卡的前提下开机，串口按enter进入uboot命令行，输入 mmc erase 0 100 reset 把emmc上的uboot破坏掉

dicsonpan commented 2 years ago

使用 batocera 模拟器是可以正常进入系统，并正常使用

dicsonpan commented 2 years ago

我使用的是tn3399_v3, 4G RAM + 16G EMMC

retro98boy commented 2 years ago

我使用的是tn3399_v3, 4G RAM + 16G EMMC

用的是emmc还是tf卡？要不把那个manjaro的镜像刻录到tf卡上，不下到emmc试试？

retro98boy commented 2 years ago

我使用的是tn3399_v3, 4G RAM + 16G EMMC

我把镜像下载下来重新打包下看看

dicsonpan commented 2 years ago

我使用的是tn3399_v3, 4G RAM + 16G EMMC

用的是emmc还是tf卡？要不把那个manjaro的镜像刻录到tf卡上，不下到emmc试试？

把 manjaro 镜像刻录到tf卡上的话，是可以正常进入的，难不成是我写入emmc的方法不对？ 我是这么操作的 rkdeveloptool db ./rk3399_loader_v1.24.126.bin rkdeveloptool wl 0x0 ./Manjaro-ARM-minimal-tn3399_v3-22.02.img

retro98boy commented 2 years ago

我使用的是tn3399_v3, 4G RAM + 16G EMMC

用的是emmc还是tf卡？要不把那个manjaro的镜像刻录到tf卡上，不下到emmc试试？

把 manjaro 镜像刻录到tf卡上的话，是可以正常进入的，难不成是我写入emmc的方法不对？ 我是这么操作的 rkdeveloptool db ./rk3399_loader_v1.24.126.bin rkdeveloptool wl 0x0 ./Manjaro-ARM-minimal-tn3399_v3-22.02.img

rkdeveloptool我没用过，我用的是windows平台下的androidtool，我等会把androidtool，maskrom驱动和androidtool下载时的分区cfg文件传上去，你用windows试试？ 估计和rkdeveloptool没关系，好像是我编译的uboot有问题，在emmc上就不能使用，之前好像解决了这个问题，现在也没法调试。 你去这里下载lanseyujie编译的uboot https://github.com/lanseyujie/tn3399_v3/releases tar.gz压缩包里有三个文件idbloader trust uboot，把他刻录到img上，再下载到emmc试试 dd if=idbloader.img of=manjaroimg seek=64 conv=notrunc dd if=uboot.img of=manjaroimg seek=16384 conv=notrunc dd if=trust.img of=manjaroimg seek=24576 conv=notrunc

dicsonpan commented 2 years ago

我使用的是tn3399_v3, 4G RAM + 16G EMMC

用的是emmc还是tf卡？要不把那个manjaro的镜像刻录到tf卡上，不下到emmc试试？

把 manjaro 镜像刻录到tf卡上的话，是可以正常进入的，难不成是我写入emmc的方法不对？ 我是这么操作的 rkdeveloptool db ./rk3399_loader_v1.24.126.bin rkdeveloptool wl 0x0 ./Manjaro-ARM-minimal-tn3399_v3-22.02.img

rkdeveloptool我没用过，我用的是windows平台下的androidtool，我等会把androidtool，maskrom驱动和androidtool下载时的分区cfg文件传上去，你用windows试试？ 估计和rkdeveloptool没关系，好像是我编译的uboot有问题，在emmc上就不能使用，之前好像解决了这个问题，现在也没法调试。 你去这里下载lanseyujie编译的uboot https://github.com/lanseyujie/tn3399_v3/releases tar.gz压缩包里有三个文件idbloader trust uboot，把他刻录到img上，再下载到emmc试试 dd if=idbloader.img of=manjaroimg seek=64 conv=notrunc dd if=uboot.img of=manjaroimg seek=16384 conv=notrunc dd if=trust.img of=manjaroimg seek=24576 conv=notrunc

这样就可以了~感谢 还有另外一个关于AX210驱动的问题，我另开一个issue