search

rizacelik / STM32F411CEU6_INAV_Firmware

STM32F411CEU6 Board Firmware
122 stars 32 forks source link

Motor 4 doesn't recieve signal after activation of gimbal #22

Closed Lalbabu2001 closed 8 months ago

Lalbabu2001 commented 8 months ago

As soon as i add s90 servo gimbal the flight controller cuts signal on m4 pin.

rizacelik commented 8 months ago

I did not do a gimbal test. Because I've never used it. Unfortunately I don't have it.

Which of the following firmware did you use? Firmware inav_6.1.1_STM32F411CE.zip OR Firmware inav_6.1.1_STM32F411CE_HEX.zip

How did you do your installation? Can you give a screenshot? Let me try to help.

Lalbabu2001 commented 8 months ago

I tested all but version 6.1.0 working great.

On Wed, Oct 25, 2023, 11:17 AM Rıza Çelik @.***> wrote:

I did not do a gimbal test. Because I've never used it. Unfortunately I don't have it.

Which of the following firmware did you use? Firmware inav_6.1.1_STM32F411CE.zip OR Firmware inav_6.1.1_STM32F411CE_HEX.zip

How did you do your installation? Can you give a screenshot? Let me try to help.

— Reply to this email directly, view it on GitHub https://github.com/rizacelik/STM32F411CEU6_INAV_Firmware/issues/22#issuecomment-1778555478, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6LQAIAZKKWAN6G7GXW5KWLYBCRWVAVCNFSM6AAAAAA6NUYYI2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTONZYGU2TKNBXHA . You are receiving this because you authored the thread.Message ID: @.***>

rizacelik commented 8 months ago

Did it work on these versions? Thank you for the feedback. Firmware inav_6.1.1_STM32F411CE.zip VEYA Firmware inav_6.1.1_STM32F411CE_HEX.zip

Lalbabu2001 commented 8 months ago

I didn't tested 6.1.1 because 6.1.0 is fine I am using mpu6500. Is there anything that activating servo on pin B10 and B1(as per your circuit diagram) changes the output pin of motor 4 ?

On Fri, Oct 27, 2023, 7:04 PM Rıza Çelik @.***> wrote:

Did it work on these versions? Thank you for the feedback. Firmware inav_6.1.1_STM32F411CE.zip VEYA Firmware inav_6.1.1_STM32F411CE_HEX.zip

— Reply to this email directly, view it on GitHub https://github.com/rizacelik/STM32F411CEU6_INAV_Firmware/issues/22#issuecomment-1782930133, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6LQAIEXGK3ZEMYDNNDRFIDYBOZ5XAVCNFSM6AAAAAA6NUYYI2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTOOBSHEZTAMJTGM . You are receiving this because you authored the thread.Message ID: @.***>

rizacelik commented 8 months ago

For INAV 6.10 and earlier the connections are different. Please see "Old version INAV Firmware Full wire connection" towards the bottom of the page. There is only 1 servo there. PB1 pin does not belong to servos. Look carefully. You need INAV version 6.1.1. Links are located at the top of the page. For multiple servos you should use this version.

Lalbabu2001 commented 8 months ago

Even if I use only one pin pb1 for servo it still no signal to motor 4.

Does inav 6.1.1 support ppm?

On Sat, Oct 28, 2023, 12:48 PM Rıza Çelik @.***> wrote:

For INAV 6.10 and earlier the connections are different. Please see "Old version INAV Firmware Full wire connection" towards the bottom of the page. There is only 1 servo there. PB1 pin does not belong to servos. Look carefully. You need INAV version 6.1.1. Links are located at the top of the page. For multiple servos you should use this version.

— Reply to this email directly, view it on GitHub https://github.com/rizacelik/STM32F411CEU6_INAV_Firmware/issues/22#issuecomment-1783730584, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6LQAIE7ZW462B74UXCYFSTYBSWUJAVCNFSM6AAAAAA6NUYYI2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTOOBTG4ZTANJYGQ . You are receiving this because you authored the thread.Message ID: @.***>

rizacelik commented 8 months ago

pin pb1 not servo

image

Yes. There is inav 6.1.1 ppm support.

Lalbabu2001 commented 8 months ago

Alright, if i want blackbox log can i connect micro sd card module because the flash chip is not available here .

On Sat, Oct 28, 2023, 6:58 PM Rıza Çelik @.***> wrote:

pin pb1 not servo

[image: image] https://user-images.githubusercontent.com/19993109/278816196-37e7789b-aac1-4db5-b912-ce1ee18ef87c.png

Yes. There is inav 6.1.1 ppm support.

— Reply to this email directly, view it on GitHub https://github.com/rizacelik/STM32F411CEU6_INAV_Firmware/issues/22#issuecomment-1783810543, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6LQAIDUUY573JUT2EKYFM3YBUCBXAVCNFSM6AAAAAA6NUYYI2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTOOBTHAYTANJUGM . You are receiving this because you authored the thread.Message ID: @.***>

rizacelik commented 8 months ago

Please see diagrams. All the information you need is available there. For Blackbox you will need one M25P16 chip. I'm closing the issue here. Enjoy your work.