USB support for "Sonoff Zigbee 3.0 USB Dongle Plus V2" & geminilake DSM 7.2

[steph54000]

Hi, I'm new to home automation and Linux... I have a Synology DS220+ geminilake DSM 7.2-64570. I bought : “Sonoff Zigbee 3.0 USB Dongle Plus V2” model "ZBDongle-E"

• Chip : CH9102/CH343 (not CC2652P)
• Silicon Labs EFR32MG21
• EmberZNet (EZSP v8)
• pre-flashing with coordinator EmberZNet 6.10.3 firmware

I followed your explanations here : https://github.com/robertklep/dsm7-usb-serial-drivers/issues/98

to sum up : Access with PuTTY sudo su

modprobe usbserial modprobe ftdi_sio modprobe cdc-acm

cd /lib/modules/

sudo wget https://github.com/robertklep/dsm7-usb-serial-drivers/raw/main/modules/geminilake/dsm-7.2/ch341.ko sudo insmod /lib/modules/ch341.ko sudo wget https://github.com/robertklep/dsm7-usb-serial-drivers/raw/main/modules/geminilake/dsm-7.2/cp210x.ko sudo insmod /lib/modules/cp210x.ko sudo wget https://github.com/robertklep/dsm7-usb-serial-drivers/raw/main/modules/geminilake/dsm-7.2/pl2303.ko sudo insmod /lib/modules/pl2303.ko sudo wget https://github.com/robertklep/dsm7-usb-serial-drivers/raw/main/modules/geminilake/dsm-7.2/ti_usb_3410_5052.ko sudo insmod /lib/modules/ti_usb_3410_5052.ko

cd /usr/local/etc/rc.d/ sudo wget https://raw.githubusercontent.com/robertklep/dsm7-usb-serial-drivers/main/usb-serial-drivers.sh sudo chmod 755 usb-serial-drivers.sh

sudo /usr/local/etc/rc.d/usb-serial-drivers.sh start

And finaly $ /usr/syno/bin/lsusb -cui |usb1 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (Linux 4.4.302+ xhci-hcd xHCI Host Controller 0000:00:15.0) hub |1-4 f400:f400:0100 00 2.00 480MBit/s 200mA 1IF (Synology DiskStation 7F001154D4CC4585) 1-4:1.0 (IF) 08:06:50 2EPs () usb-storage host2 (synoboot)

I guess I don't have the good driver "CH9102.ko or CH343.ko" but I don't understand what to do here: https://github.com/WCHSoftGroup/ch343ser_linux

To be sure of the key, I flashed again in coordinator EmberZNet 6.10.3 firmware but it's the same.

Can anyone help me ? Thanks

[robertklep]

It should work with the ch341.ko driver. Are you sure it's loaded correctly? What does lsmod -a | grep serial show?

[robertklep]

Oh never mind, it looks like the Synology cannot even see your device, it should be shown in the output of lsusb but it isn't. This is independent of whether there's a driver installed or not, it should show as a USB device. Try removing it and plugging it back in again.

[steph54000]

Hi, dmesg | grep -i serial [ 0.000000] Command line: root=/dev/md0 intel_iommu=igfx_off netif_num=2 HddEnableDynamicPower=1 syno_hw_version=DS220+ vender_format_version=2 synoboot 2 sn=2290RLR7X4CAV macs=9009d030a827,9009d030a828 syno_ttyS0=pciserial,0x0:0x18.0x2,115200 syno_ttyS1=pciserial,0x0:0x18.0x0,115200 [ 0.000000] Kernel command line: root=/dev/md0 intel_iommu=igfx_off netif_num=2 HddEnableDynamicPower=1 syno_hw_version=DS220+ vender_format_version=2 s ynoboot2 sn=2290RLR7X4CAV macs=9009d030a827,9009d030a828 syno_ttyS0=pciserial,0x0:0x18.0x2,115200 syno_ttyS1=pciserial,0x0:0x18.0x0,115200 [ 0.000000] Serial Number: 2290RLR7X4CAV [ 5.017685] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 42.425537] systemd[1]: Created slice synokernel-usbserial's slice. [ 42.438651] systemd[1]: Starting synokernel-usbserial's slice. [ 43.186739] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 43.199874] systemd[1]: Starting system-serial\x2dgetty.slice. [ 68.178569] usbcore: registered new interface driver usbserial [ 68.210709] usbserial: USB Serial support registered for FTDI USB Serial Device [ 68.312563] usbserial: USB Serial support registered for cp210x [ 68.367815] usbserial: USB Serial support registered for ch341-uart [ 68.552545] usbserial: USB Serial support registered for pl2303 [ 68.826786] usbserial: USB Serial support registered for TI USB 3410 1 port adapter [ 68.835360] usbserial: USB Serial support registered for TI USB 5052 2 port adapter

[steph54000]

lsmod | grep serial

usbserial 22278 5 ch341,cp210x,ti_usb_3410_5052,pl2303,ftdi_sio usbcore 209065 17 uas,ch341,etxhci_hcd,usblp,uhci_hcd,usb_storage,cp210x,usbserial,ti_usb_3410_5052,ehci_hcd,ehci_pci,pl2303,usbhid,ftdi_sio,cdc_acm,xhci_hcd,xhci_pci

[steph54000]

unplug and plug not change the state

[robertklep]

The required modules are loaded, so this looks to be a hardware issue 😢 Do you have a PC or Mac that you can plug the Sonoff dongle in to to see if anything happens there?

[steph54000]

hi, on my PC :

And, to be sure, i I flashed it in coordinator EmberZNet 6.10.3 firmware but it's the same

[steph54000]

Maybe a CH343 pilot ? https://github.com/WCHSoftGroup/ch343ser_linux https://blog.csdn.net/WCH_TechGroup/article/details/132173723

I tested he firmware : Zigbee (EZSP) 7.3.1.0 build 176 but no change

[robertklep]

As I explained: your Synology doesn't even see the device is plugged in, otherwise it would have shown up in the output of lsusb. That's a hardware issue.

Try using a USB extension cord to see if that makes it show up.

[steph54000]

It’s miraculous, it works! The dongle plugged directly into the NAS is not recognized. I just added an USB extension, everything works. Many thanks my friend!

[robertklep]

Have fun!