search

rssnsj / openwrt-hc5x61

OpenWrt Patch for HiWiFi HC5661 / HC5761 / HC5861
http://rssn.cn/roms/
589 stars 174 forks source link

HC5761的USB能够使用么？ #13

Closed paradislover closed 9 years ago

paradislover commented 9 years ago

发现插入优盘或者FTDI设备，一点反应都没有？需要安装哪些模块？

paradislover commented 9 years ago
  1. U盘插入，重启路由器可以识别，热插拔不能识别
  2. FTDI设备不能识别

请问和DTS文件配置有关么？

paradislover commented 9 years ago

附上插入FTDI设备的LOG： [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is HiWiFi HC5761 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 802d4990, node_mem_map 81006600 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=0003b42a [ 0.000000] Readback ErrCtl register=0003b42a [ 0.000000] Memory: 126484k/131072k available (2396k kernel code, 4588k reserved, 592k data, 208k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.050000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] pinctrl core: initialized pinctrl subsystem [ 0.070000] NET: Registered protocol family 16 [ 0.080000] rt2880-pinmux pinctrl.1: try to register 73 pins ... [ 0.080000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 52 (io52) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 53 (io53) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 54 (io54) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 55 (io55) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 56 (io56) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 57 (io57) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 58 (io58) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 59 (io59) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 60 (io60) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 61 (io61) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 62 (io62) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 63 (io63) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 64 (io64) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 65 (io65) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 66 (io66) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 67 (io67) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 68 (io68) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 69 (io69) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 70 (io70) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 71 (io71) on rt2880-pinmux [ 0.080000] pinctrl core: registered pin 72 (io72) on rt2880-pinmux [ 0.080000] pinctrl core: add 4 pinmux maps [ 0.080000] rt2880-pinmux pinctrl.1: found group selector 1 for uartf [ 0.080000] rt2880-pinmux pinctrl.1: found group selector 11 for wled [ 0.080000] rt2880-pinmux pinctrl.1: found group selector 9 for nd_sd [ 0.080000] rt2880-pinmux pinctrl.1: found group selector 13 for pa [ 0.080000] rt2880-pinmux pinctrl.1: request pin 7 (io7) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 8 (io8) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 9 (io9) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 10 (io10) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 11 (io11) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 12 (io12) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 13 (io13) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 14 (io14) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 72 (io72) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 45 (io45) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 46 (io46) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 47 (io47) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 48 (io48) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 49 (io49) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 50 (io50) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 51 (io51) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 52 (io52) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 53 (io53) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 54 (io54) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 55 (io55) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 56 (io56) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 57 (io57) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 58 (io58) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 59 (io59) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 18 (io18) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 19 (io19) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 20 (io20) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: request pin 21 (io21) for pinctrl.1 [ 0.080000] rt2880-pinmux pinctrl.1: failed to lookup the sleep state [ 0.520000] bio: create slab at 0 [ 0.530000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.530000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.540000] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.540000] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.550000] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.550000] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.560000] PCI host bridge to bus 0000:00 [ 0.560000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.570000] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff] [ 0.570000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.580000] pci 0000:00:00.0: [1814:0802] type 01 class 0x060400 [ 0.580000] pci 0000:00:00.0: reg 14: [mem 0x00000000-0x0000ffff] [ 0.580000] pci 0000:00:00.0: supports D1 [ 0.580000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.580000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.580000] pci 0000:01:00.0: [14c3:7650] type 00 class 0x028000 [ 0.580000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x000fffff] [ 0.580000] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.580000] pci 0000:01:00.1: [14c3:8650] type 00 class 0x0d1100 [ 0.580000] pci 0000:01:00.1: reg 10: [mem 0x00000000-0x000fffff] [ 0.580000] pci 0000:01:00.1: supports D1 [ 0.580000] pci 0000:01:00.1: PME# supported from D0 D1 D3hot D3cold [ 0.590000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.590000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.590000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] [ 0.590000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.600000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] [ 0.600000] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.610000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.610000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 0.620000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 0.620000] Switching to clocksource MIPS [ 0.630000] NET: Registered protocol family 2 [ 0.630000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.640000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.650000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.650000] TCP: reno registered [ 0.660000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.660000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.670000] NET: Registered protocol family 1 [ 0.670000] PCI: CLS 80 bytes, default 32 [ 0.670000] rt-timer 10000100.timer: maximum frequncy is 2441Hz [ 0.680000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT [ 0.700000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.700000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.710000] msgmni has been set to 247 [ 0.720000] io scheduler noop registered [ 0.720000] io scheduler deadline registered (default) [ 0.730000] rt2880-pinmux pinctrl.1: request pin 13 (io13) for pio:13 [ 0.730000] gpio-export gpio_export.6: 1 gpio(s) exported [ 0.730000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.740000] serial8250 serial8250: no of_node; not parsing pinctrl DT [ 0.740000] pinctrl core: add 1 pinmux maps [ 0.740000] rt2880-pinmux pinctrl.1: found group selector 3 for uartlite [ 0.740000] rt2880-pinmux pinctrl.1: request pin 15 (io15) for 10000c00.uartlite [ 0.740000] rt2880-pinmux pinctrl.1: request pin 16 (io16) for 10000c00.uartlite [ 0.740000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.750000] console [ttyS0] enabled, bootconsole disabled [ 0.760000] pinctrl core: add 1 pinmux maps [ 0.760000] rt2880-pinmux pinctrl.1: found group selector 2 for spi [ 0.760000] rt2880-pinmux pinctrl.1: request pin 3 (io3) for 10000b00.spi [ 0.760000] rt2880-pinmux pinctrl.1: request pin 4 (io4) for 10000b00.spi [ 0.760000] rt2880-pinmux pinctrl.1: request pin 5 (io5) for 10000b00.spi [ 0.760000] rt2880-pinmux pinctrl.1: request pin 6 (io6) for 10000b00.spi [ 0.760000] m25p80 spi32766.0: w25q128 (16384 Kbytes) [ 0.770000] 7 ofpart partitions found on MTD device spi32766.0 [ 0.770000] Creating 7 MTD partitions on "spi32766.0": [ 0.780000] 0x000000000000-0x000000030000 : "u-boot" [ 0.790000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.790000] 0x000000040000-0x000000050000 : "factory" [ 0.800000] 0x000000050000-0x000000fd0000 : "firmware" [ 0.810000] 0x0000001587c1-0x000000fd0000 : "rootfs" [ 0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.830000] mtd: device 4 (rootfs) set to be root filesystem [ 0.830000] mtd: partition "rootfs_data" created automatically, ofs=0x760000, len=0x870000 [ 0.840000] 0x000000760000-0x000000fd0000 : "rootfs_data" [ 0.850000] 0x000000fd0000-0x000000fe0000 : "hwf_config" [ 0.860000] 0x000000fe0000-0x000000ff0000 : "bdinfo" [ 0.860000] 0x000000ff0000-0x000001000000 : "backup" [ 0.870000] pinctrl core: add 1 pinmux maps [ 0.870000] pinctrl core: add 1 pinmux maps [ 0.870000] pinctrl core: add 1 pinmux maps [ 0.870000] rt2880-pinmux pinctrl.1: found group selector 6 for rgmii1 [ 0.870000] rt2880-pinmux pinctrl.1: found group selector 10 for rgmii2 [ 0.870000] rt2880-pinmux pinctrl.1: found group selector 5 for mdio [ 0.870000] rt2880-pinmux pinctrl.1: request pin 24 (io24) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 25 (io25) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 26 (io26) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 27 (io27) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 28 (io28) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 29 (io29) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 30 (io30) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 31 (io31) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 32 (io32) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 33 (io33) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 34 (io34) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 35 (io35) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 60 (io60) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 61 (io61) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 62 (io62) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 63 (io63) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 64 (io64) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 65 (io65) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 66 (io66) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 67 (io67) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 68 (io68) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 69 (io69) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 70 (io70) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 71 (io71) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 22 (io22) for 10100000.ethernet [ 0.870000] rt2880-pinmux pinctrl.1: request pin 23 (io23) for 10100000.ethernet [ 0.870000] gsw: setting port4 to ephy mode [ 0.880000] ralink_soc_eth 10100000.ethernet (unregistered net_device): port 0 link up (100Mbps/Full duplex) [ 0.890000] libphy: mdio: probed [ 0.890000] port: invalid port id 4 [ 0.900000] ralink_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=0000ffff, driver=Generic PHY] [ 0.910000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.920000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 0.920000] rt3xxx-usbphy usbphy.3: loaded [ 0.930000] rt2880_wdt 10000120.watchdog: Initialized [ 0.940000] TCP: cubic registered [ 0.940000] NET: Registered protocol family 17 [ 0.940000] 8021q: 802.1Q VLAN Support v1.8 [ 0.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.970000] Freeing unused kernel memory: 208K (802ec000 - 80320000) [ 6.820000] usbcore: registered new interface driver usbfs [ 6.820000] usbcore: registered new interface driver hub [ 6.830000] usbcore: registered new device driver usb [ 6.860000] rt2880-pinmux pinctrl.1: request pin 12 (io12) for pio:12 [ 6.870000] SCSI subsystem initialized [ 6.880000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.890000] ehci-platform: EHCI generic platform driver [ 7.100000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled [ 7.100000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz [ 7.110000] ehci-platform 101c0000.ehci: EHCI Host Controller [ 7.110000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 7.120000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 7.150000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 7.150000] usb usb1: no of_node; not parsing pinctrl DT [ 7.150000] hub 1-0:1.0: no of_node; not parsing pinctrl DT [ 7.150000] hub 1-0:1.0: USB hub found [ 7.160000] hub 1-0:1.0: 1 port detected [ 7.170000] leds-gpio gpio-leds.5: pins are not configured from the driver [ 7.170000] rt2880-pinmux pinctrl.1: request pin 9 (io9) for pio:9 [ 7.180000] rt2880-pinmux pinctrl.1: request pin 11 (io11) for pio:11 [ 7.180000] rt2880-pinmux pinctrl.1: request pin 72 (io72) for pio:72 [ 7.180000] rt2880-pinmux pinctrl.1: request pin 7 (io7) for pio:7 [ 7.190000] sdhci: Secure Digital Host Controller Interface driver [ 7.190000] sdhci: Copyright(c) Pierre Ossman [ 7.200000] MTK MSDC device init. [ 7.240000] mtk-sd: MediaTek MT6575 MSDC Driver [ 7.240000] sdhci-pltfm: SDHCI platform and OF driver helper [ 7.250000] usbcore: registered new interface driver usb-storage [ 7.440000] mmc0: new high speed SDHC card at address aaaa [ 7.460000] mmcblk mmc0:aaaa: no of_node; not parsing pinctrl DT [ 7.460000] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 7.470000] mmcblk0: p1 p2 [ 8.060000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 9.130000] ralink_soc_eth 10100000.ethernet eth0: port 5 link up (10Mbps/Half duplex) [ 12.300000] jffs2: notice: (357) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 15 of xref (0 dead, 2 orphan) found. [ 12.500000] jffs2: notice: (354) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 15 of xref (0 dead, 2 orphan) found. [ 13.130000] ralink_soc_eth 10100000.ethernet eth0: port 5 link down [ 14.970000] NET: Registered protocol family 10 [ 15.030000] RPC: Registered named UNIX socket transport module. [ 15.030000] RPC: Registered udp transport module. [ 15.040000] RPC: Registered tcp transport module. [ 15.040000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 15.060000] NTFS driver 2.1.30 [Flags: R/O MODULE]. [ 15.080000] tun: Universal TUN/TAP device driver, 1.6 [ 15.080000] tun: (C) 1999-2004 Max Krasnyansky maxk@qualcomm.com [ 15.100000] ipip: IPv4 over IPv4 tunneling driver [ 15.120000] l2tp_core: L2TP core driver, V2.0 [ 15.130000] l2tp_netlink: L2TP netlink interface [ 15.130000] sit: IPv6 over IPv4 tunneling driver [ 15.150000] gre: GRE over IPv4 demultiplexor driver [ 15.150000] ip_gre: GRE over IPv4 tunneling driver [ 15.240000] nf_conntrack version 0.5.0 (1979 buckets, 7916 max) [ 15.270000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 15.340000] Netfilter messages via NETLINK v0.30. [ 15.360000] ip_set: protocol 6 [ 15.420000] u32 classifier [ 15.430000] input device check on [ 15.430000] Actions configured [ 15.450000] Mirror/redirect action on [ 15.470000] fuse init (API version 7.22) [ 15.490000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 15.500000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 15.540000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.590000] usbcore: registered new interface driver usbserial [ 15.590000] usbcore: registered new interface driver usbserial_generic [ 15.600000] usbserial: USB Serial support registered for generic [ 15.670000] xt_time: kernel timezone is -0000 [ 15.740000] cfg80211: Calling CRDA to update world regulatory domain [ 15.740000] cfg80211: World regulatory domain updated: [ 15.750000] cfg80211: DFS Master region: unset [ 15.750000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 15.760000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 15.770000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 15.780000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 15.790000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A) [ 15.800000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 15.800000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 15.810000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 15.820000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 15.830000] usbcore: registered new interface driver ftdi_sio [ 15.850000] usbserial: USB Serial support registered for FTDI USB Serial Device [ 15.910000] PPP generic driver version 2.4.2 [ 15.920000] PPP MPPE Compression module registered [ 15.930000] NET: Registered protocol family 24 [ 15.940000] PPTP driver version 0.8.5 [ 15.970000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 16.010000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected [ 16.020000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 16.030000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 23.420000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 23.440000] device eth0.1 entered promiscuous mode [ 23.440000] device eth0 entered promiscuous mode [ 23.460000] br-lan: port 1(eth0.1) entered forwarding state [ 23.470000] br-lan: port 1(eth0.1) entered forwarding state [ 24.210000] cfg80211: Calling CRDA for country: US [ 24.250000] cfg80211: Regulatory domain changed to country: US [ 24.250000] cfg80211: DFS Master region: FCC [ 24.260000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 24.270000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 24.270000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A) [ 24.280000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s) [ 24.290000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 24.300000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 24.410000] ralink_soc_eth 10100000.ethernet eth0: port 5 link up (10Mbps/Half duplex) [ 25.470000] br-lan: port 1(eth0.1) entered forwarding state [ 26.480000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 26.480000] device wlan0 entered promiscuous mode [ 26.490000] br-lan: port 2(wlan0) entered forwarding state [ 26.500000] br-lan: port 2(wlan0) entered forwarding state [ 26.500000] br-lan: port 2(wlan0) entered disabled state [ 34.960000] br-lan: port 2(wlan0) entered forwarding state [ 34.960000] br-lan: port 2(wlan0) entered forwarding state [ 34.970000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 36.960000] br-lan: port 2(wlan0) entered forwarding state

rssnsj commented 9 years ago

USB驱动已经完善，极2 USB能用。

Sent from my iPhone

On Feb 10, 2015, at 10:57, paradislover notifications@github.com wrote:

发现插入优盘或者FTDI设备，一点反应都没有？需要安装哪些模块？

— Reply to this email directly or view it on GitHub.

paradislover commented 9 years ago

多谢，已解决，编译时：

CONFIG_PACKAGE_kmod-usb-ohci=y 即可

MARK