rusefi uaefi issues - Githubissues

rusefi / uaefi

6 stars 10 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

improve "real hot" explanation

#65 rusefillc opened 1 month ago
0
happypath REV C ordering wrong orientation elements

#64 ggurov closed 1 month ago
1
alternative/nicer connector + enclosure combo

#63 rusefillc opened 2 months ago
2
BT module silk

#62 rusefillc opened 2 months ago
0
Wbo FW something about dfferent versions

#61 rusefillc opened 2 months ago
0
hold on we forgot about SPI for TLE9201?

#60 rusefillc opened 2 months ago
0
certain UAEFI boards do not initialize 5VP below certain 12v input voltage when they should totally do so cause vehicle batteries can drain lower than that

#59 ggurov opened 3 months ago
9
2.54mm spacing inside the molex connector is only 2.54 within the group not relative to another one

#58 ggurov opened 3 months ago
0
pad for resistor between VR lines

#57 rusefillc closed 3 months ago
3
Add "hall mode" silkscreen note next to R1

#56 rusefillc closed 3 months ago
1
WBO stm32f042 has died

#55 rusefillc closed 4 months ago
2
make on-board MAP sensor pinout more obvious

#54 rusefillc closed 3 months ago
4
Add EGT passives into BOM

#53 rusefillc closed 3 months ago
3
IGN output comment

#52 rusefillc closed 3 months ago
1
silkscreen on UAEFI mislabels B9 as LSW3, it should be LSW1

#51 ggurov closed 3 months ago
1
rename VR networks

#50 rusefillc closed 3 months ago
2
can H/L silk top vs bottom

#49 rusefillc closed 3 months ago
1
document "ac-request input, button2, d10, is that 12v tollerant ?"

#48 rusefillc opened 4 months ago
0
rename VR1 to VR1_DISCRETE

#47 rusefillc closed 4 months ago
0
fab B U107 orientation

#46 rusefillc opened 4 months ago
2
HOWTO dual WBO?

#45 rusefillc opened 5 months ago
0
no current limit on uln2003

#44 rusefillc closed 5 months ago
1
.

#43 rusefillc closed 5 months ago
0
ign x6 fuse official work-around

#42 rusefillc closed 5 months ago
0
самые простые группы 2x2 0.1"

#41 rusefillc closed 5 months ago
0
cost reduction ideas - а нужен ли вообще усилитель на аналоговых входах?

#40 rusefillc opened 5 months ago
0
via for dc2 control lines

#39 rusefillc closed 5 months ago
1
recommended pinout part 2

#38 rusefillc closed 5 months ago
4
подписать рекомендованные назначения пинов синим

#37 rusefillc closed 5 months ago
3
physically larger pulldown 4.7k-10k on button lines

#36 rusefillc closed 5 months ago
5
cost reduction ideas

#35 rusefillc closed 5 months ago
5
Add 2.54mm header while not changing board size

#34 rusefillc closed 5 months ago
3
bump version to rev B

#33 rusefillc closed 5 months ago
1
C117, C123 fix again

#32 rusefillc closed 5 months ago
3
how about VNL5160 for Qx

#31 rusefillc closed 5 months ago
3
ISL9V3040 status

#30 rusefillc closed 5 months ago
1
"COMMUNITY SUPPORT ECU" silk on both sides

#29 rusefillc closed 5 months ago
3
with wideband warming up sensor batter V reports +5v

#28 rusefillc closed 6 months ago
1
proto area G/3/5/12 silk on back side

#27 rusefillc closed 5 months ago
1
knock headphones pins

#26 rusefillc opened 6 months ago
1
rev A testing

#25 rusefillc opened 6 months ago
1
bundle logo

#24 rusefillc opened 6 months ago
0
confirm pin compatibility STM32F429VIT6

#23 rusefillc closed 5 months ago
1
molex 3D

#22 rusefillc closed 5 months ago
2
review fab files

#21 rusefillc closed 7 months ago
0
диагностика КЗ 5в

#20 rusefillc closed 7 months ago
2
скруглить углы?

#19 rusefillc closed 7 months ago
1
шёлк и наверху тоже

#18 rusefillc closed 7 months ago
1
дефект рендера или?

#17 rusefillc opened 7 months ago
2
J6 part number

#16 rusefillc closed 7 months ago
0