search

shalxmva / modxo

Xbox LPC Port modchip using a Raspberry Pi Pico
BSD 2-Clause "Simplified" License
320 stars 16 forks source link

Xbox not see rpi pico bios install on older version #1

Closed M007P closed 5 months ago

M007P commented 5 months ago

Can you update install guide for older version 1.0 to 1.5 with pic if posible .

I have Xbox OG 1.1( have more Xbox OG rev ) on witch i installed 2 pico zeros to test and not load Cerber bios logo just default bios animation. If need info instaled and no HDD, DVD instaled when testing.

Lifting bios leg on board is needed only for rev 1.6/1.6b ?

Thanks for support

yakaracolombia commented 5 months ago

you need to get Lframe from the mpcx, https://xboxdevwiki.net/LPC_Debug_Port

M007P commented 5 months ago

i found out in the morning D0 to GND :-), been tiered and missed. Found out that black rpi pico not working, picture below. do not buy this RPI PICO for modchip IMG_3644

Classic model works as should, new revisons of rpi pico not working.

M007P commented 5 months ago

i used 4 x 100ohm 0805 with pink RPI😂 Barbie style no problem. IMG_3645 IMG_3647

yakaracolombia commented 5 months ago

do you wire the Lframe from mpcx or just d0 to gnd?

davidxgames commented 5 months ago

@yakaracolombia

consoles 1.0 - 1.2 only D0 to gnd. consoles 1.3 - 1.5 D0 to gnd, and mpcx. 1.6 consoles rebuild LPC and lift Xyclops chip pin.

M007P commented 5 months ago

i have done one console rev 1.3 by date with ?? on wiki, needed Lframe from MPCX to work. On console info show rev 1.2. D0 to GND.

do you wire the Lframe from mpcx or just d0 to gnd?

It was rev 1.1 not needed.

shalxmva commented 5 months ago

i found out in the morning D0 to GND :-), been tiered and missed. Found out that black rpi pico not working, picture below. do not buy this RPI PICO for modchip IMG_3644

Classic model works as should, new revisons of rpi pico not working.

That version is working for me, but i tested other black models and a green clone that doesnt have any raspberry logos to no work.

Which size number your resistors are?

M007P commented 5 months ago

i found out in the morning D0 to GND :-), been tiered and missed. Found out that black rpi pico not working, picture below. do not buy this RPI PICO for modchip IMG_3644 Classic model works as should, new revisons of rpi pico not working.

That version is working for me, but i tested other black models and a green clone that doesnt have any raspberry logos to no work.

Which size number your resistors are?

its 0805 size (2mm x 1.25mm)i had only them

Androxilogin commented 5 months ago

Hah, I had two questions that were both answered here:

1) is this compatible with boards other than the v1.6? 2) Does the v1.6 require LPC rebuild?

Thanks for clearing this up by asking the same questions I had.

M007P commented 5 months ago

Hah, I had two questions that were both answered here:

  1. is this compatible with boards other than the v1.6?
  2. Does the v1.6 require LPC rebuild?

Thanks for clearing this up by asking the same questions I had.

  1. Yes i have done on 1.1 and 1.3
  2. You need to rebuild and D0 and MPCX as with other chips.
M007P commented 5 months ago

all solved