search

sthetix / DIAGRAM

The Diagram
300 stars 22 forks source link

Oled chip #7

Open smashthony opened 2 years ago

smashthony commented 2 years ago

Hi I just finished installed my oled chip but when I press on it blinks like a greenish yellow 3 times and on the 3rd in it’s longer then it flashes red once then the same process over and over help pls

sthetix commented 2 years ago

Most of the time it is doe to the dat0 losing connection.. Please check it again

On Tue, May 17, 2022, 09:06 smashthony @.***> wrote:

Hi I just finished installed my oled chip but when I press on it blinks like a greenish yellow 3 times and on the 3rd in it’s longer then it flashes red once then the same process over and over help pls

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D2OLCDUTDVLAHRBJMLVKL5KBANCNFSM5WDKK5DA . You are receiving this because you are subscribed to this thread.Message ID: @.***>

smashthony commented 2 years ago

How do I fix that I need help please

sthetix commented 2 years ago

Better wait for my upcoming short video today.

On Tue, May 17, 2022, 09:40 smashthony @.***> wrote:

How do I fix that I need help please

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128340562, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D2A2ZH2T4BMHNQTO2LVKMBKVANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

How long until its comes out in trying to get this done before I go to bed 😭😭😭

sthetix commented 2 years ago

Today means in several hours upto 12 hours. It's 9.45 am here. I mean time u need to check the soldering points diode values. Just like I did in the installation video

On Tue, May 17, 2022, 09:45 smashthony @.***> wrote:

How long until its comes out in trying to get this done before I go to bed 😭😭😭

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128342745, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D7VGCX2LKZMC4455UTVKMB2ZANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

Also the RST point shows 0 on my multimeter

sthetix commented 2 years ago

Rst 0 is ok.. Dat0 (C) should not be 0.

On Tue, May 17, 2022, 09:47 smashthony @.***> wrote:

Also the RST point shows 0 on my multimeter

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128348385, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D7Z256DO5WDPS6U4VDVKMCDVANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

Just checked all the points it was the A point it had a 0

sthetix commented 2 years ago

That is causing the issue. Maybe the resistor of that A point is damaged. Please check that

On Tue, May 17, 2022, 10:23 smashthony @.***> wrote:

Just checked all the points it was the A point it had a 0

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128365760, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23DZTIF7IJYOMJ76WYHLVKMGKVANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

It's showing a value now but I'm still having the light problem

sthetix commented 2 years ago

The resistor should be 4.7k ohm..remove the chip wires (3.3v, rst, and gnd), and see if you can boot ur console normally

On Tue, May 17, 2022, 10:26 smashthony @.***> wrote:

It's showing a value now but I'm still having the light problem

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128367099, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D7Y3RQ24GLRILLETBTVKMGVLANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

Just checked I can boot

sthetix commented 2 years ago

Then u need to recheck the dat0 connection or the cpu flex ribbon pads

On Tue, May 17, 2022, 10:32 smashthony @.***> wrote:

Just checked I can boot

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128370191, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D2OQMUYRQOVZS4ACSTVKMHMHANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

I cant*

sthetix commented 2 years ago

No boot? Check the résistance value on the A point. It should have 4.7k.ohm. If more than that, u need to replace the resistor.

On Tue, May 17, 2022, 10:33 smashthony @.***> wrote:

I cant*

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128370808, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D7EI4IWIABP3PEIN3DVKMHQZANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

It's not work

smashthony commented 2 years ago

What resistor do I need and how do I do this I wish I could send it to you😭😭😭

sthetix commented 2 years ago

U better find someone near you to fix the console issue. It could be many things.

On Tue, May 17, 2022, 10:57 smashthony @.***> wrote:

It's not work

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128381481, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D375X5UUGNEBAJMSBTVKMKMJANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

sthetix commented 2 years ago

If u are in USA, try contacting @., if u are in Europe, contact @.

On Tue, May 17, 2022, 10:58 smashthony @.***> wrote:

What resistor do I need and how do I do this I wish I could send it to you 😭😭😭

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128381830, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D3DY36TQI2PXV34XALVKMKPTANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

The email is blank

sthetix commented 2 years ago

Ask them or contact them using Twitter

@ModzvilleUSA or @zzattack

Fyi I am in indonesia, it's too far to send the console to me

On Tue, May 17, 2022, 11:01 smashthony @.***> wrote:

The email is blank

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1128382849, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D5WBVZKOCFJEOU6UB3VKMKYNANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

Thank you also what resistor is that where to I get the price to replace it?

sthetix commented 2 years ago

4.7k ohm resistor on point A.. 0201 size. You can find it anywhere

On Sun, May 22, 2022, 01:41 smashthony @.***> wrote:

Thank you also what resistor is that where to I get the price to replace it?

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1133750037, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D4JCCM6C4EV2LPKABLVLEU7FANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>

smashthony commented 2 years ago

https://www.ebay.com/itm/143468459224

Is that ok?

sthetix commented 2 years ago

Yes! you can use that

On Sun, 22 May 2022 at 16:22, smashthony @.***> wrote:

https://www.ebay.com/itm/143468459224

Is that ok?

— Reply to this email directly, view it on GitHub https://github.com/sthetix/DIAGRAM/issues/7#issuecomment-1133854225, or unsubscribe https://github.com/notifications/unsubscribe-auth/AFJ23D7MP7BR4EU2HSV2LJTVLH4GBANCNFSM5WDKK5DA . You are receiving this because you commented.Message ID: @.***>