R1plus使用闪迪ultraTF卡无法正常启动

[LCW0NJUPT]

一、问题描述：无法启动该镜像

硬件：R1Plus 固件版本： 2021-04-21 r1p-with-docker.img.gz TF卡：闪迪ultra16GB 测试了官方的openwrt镜像是可以正常启动运行的，排除了硬件故障的可能，因此来这里反馈

很想知道是不是固件兼容性的问题

二、 以下为串口打印的开机日志

DDR version 1.16 20190528
ID:0x805 N
In
DDR4
333MHz
Bus Width=32 Col=10 Bank=4 Bank Group=2 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
ddrconfig:14
OUT
Boot1 Release Time: May 13 2019 17:34:36, version: 2.50
ChipType = 0x11, 248
mmc2:cmd1,20
emmc reinit
mmc2:cmd1,20
emmc reinit
mmc2:cmd1,20
SdmmcInit=2 1
mmc0:cmd5,20
SdmmcInit=0 0
BootCapSize=0
UserCapSize=15193MB
FwPartOffset=2000 , 0
StorageInit ok = 33223
Raw SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT 0x337a9f0 signature is wrong
recovery gpt...
GPT 0x337a9f0 signature is wrong
recovery gpt fail!
LoadTrust Addr:0x4000
No find bl30.bin
No find bl32.bin
Load uboot, ReadLba = 2000
hdr 000000000337a3b0 + 0x0:0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

Load OK, addr=0x200000, size=0xa5958
RunBL31 0x40000
INFO:    Preloader serial: 2
NOTICE:  BL31: v1.3(debug):403e0b816
NOTICE:  BL31: Built : 14:13:08, Aug 11 2020
NOTICE:  BL31:Rockchip release version: v1.3
INFO:    ARM GICv2 driver initialized
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 1
INFO:    plat_rockchip_pmu_init: pd status 0xe
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK

ERROR:   Error initializing runtime service opteed_fast

INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9

U-Boot 2021.01 (Apr 07 2021 - 15:20:37 +0000) OpenWrt

Model: Xunlong Orange Pi R1 Plus
DRAM:  1022 MiB
PMIC:  RK8050 (on=0x10, off=0x00)
MMC:   mmc@ff500000: 1
Loading Environment from MMC... MMC Device 0 not found

*** Warning - No MMC card found, using default environment

In:    serial@ff130000
Out:   serial@ff130000
Err:   serial@ff130000
Model: Xunlong Orange Pi R1 Plus
Net:   eth0: ethernet@ff540000
Hit any key to stop autoboot:  0
MMC Device 0 not found
no mmc device at slot 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot.scr
352 bytes read in 2 ms (171.9 KiB/s)
## Executing script at 00500000
46966 bytes read in 6 ms (7.5 MiB/s)
13142024 bytes read in 573 ms (21.9 MiB/s)
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Device Tree to 000000003df25000, end 000000003df33775 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.4.113 (runner@fv-az294-362) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r9530-b5a3340a9)) #0 SMP PREEMPT Sun Apr 18 15:52:56 2021
[    0.000000] Machine model: Xunlong Orange Pi R1 Plus
[    0.000000] earlycon: uart8250 at MMIO32 0x00000000ff130000 (options '')
[    0.000000] printk: bootconsole [uart8250] enabled
[    0.000000] cma: Reserved 8 MiB at 0x000000003f800000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 21 pages/cpu s46104 r8192 d31720 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 257544
[    0.000000] Kernel command line: console=ttyS2,1500000 earlycon=uart8250,mmio32,0xff130000 root=PARTUUID=5452574f-02 rw rootwait
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1004152K/1046528K available (7934K kernel code, 546K rwdata, 2572K rodata, 1728K init, 730K bss, 34184K reserved, 8192K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] random: get_random_bytes called from start_kernel+0x29c/0x398 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000010] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001570] Console: colour dummy device 80x25
[    0.002032] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.002963] pid_max: default: 32768 minimum: 301
[    0.003665] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.004344] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.007310] ASID allocator initialised with 32768 entries
[    0.007941] rcu: Hierarchical SRCU implementation.
[    0.009649] smp: Bringing up secondary CPUs ...
[    0.010793] Detected VIPT I-cache on CPU1
[    0.010878] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.011672] Detected VIPT I-cache on CPU2
[    0.011735] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.012468] Detected VIPT I-cache on CPU3
[    0.012525] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.012639] smp: Brought up 1 node, 4 CPUs
[    0.015939] SMP: Total of 4 processors activated.
[    0.016373] CPU features: detected: 32-bit EL0 Support
[    0.016842] CPU features: detected: CRC32 instructions
[    0.024921] CPU: All CPU(s) started at EL2
[    0.025359] alternatives: patching kernel code
[    0.041533] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.042494] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.043741] pinctrl core: initialized pinctrl subsystem
[    0.045291] NET: Registered protocol family 16
[    0.048448] DMA: preallocated 2048 KiB pool for atomic allocations
[    0.050276] cpuidle: using governor menu
[    0.051011] Serial: AMBA PL011 UART driver
[    0.082431] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.083055] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.083665] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.084271] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.089005] sdmmc-regulator GPIO handle specifies active low - ignored
[    0.091705] iommu: Default domain type: Translated
[    0.093456] SCSI subsystem initialized
[    0.094131] usbcore: registered new interface driver usbfs
[    0.094692] usbcore: registered new interface driver hub
[    0.095280] usbcore: registered new device driver usb
[    0.096708] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.098682] clocksource: Switched to clocksource arch_sys_counter
[    0.099501] VFS: Disk quotas dquot_6.6.0
[    0.099944] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.106701] thermal_sys: Registered thermal governor 'step_wise'
[    0.106710] thermal_sys: Registered thermal governor 'power_allocator'
[    0.107917] NET: Registered protocol family 2
[    0.109815] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.110604] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.111455] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.112298] TCP: Hash tables configured (established 8192 bind 8192)
[    0.113074] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.113719] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.114646] NET: Registered protocol family 1
[    0.115125] PCI: CLS 0 bytes, default 64
[    0.117135] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    0.128090] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.128633] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.157394] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.158076] io scheduler mq-deadline registered
[    0.165800] dma-pl330 ff1f0000.dmac: Loaded driver for PL330 DMAC-241330
[    0.166426] dma-pl330 ff1f0000.dmac:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    0.170076] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.172832] ff120000.serial: ttyS1 at MMIO 0xff120000 (irq = 12, base_baud = 1500000) is a 16550A
[    0.174564] ff130000.serial: ttyS2 at MMIO 0xff130000 (irq = 13, base_baud = 1500000) is a 16550A
[    0.175522] printk: console [ttyS2] enabled
[    0.175522] printk: console [ttyS2] enabled
[    0.176275] printk: bootconsole [uart8250] disabled
[    0.176275] printk: bootconsole [uart8250] disabled

[    0.179888] rockchip-drm display-subsystem: [drm:rockchip_drm_platform_probe] *ERROR* No available vop found for display-subsystem.

[    0.181472] lima ff300000.gpu: IRQ pmu not found
[    0.182100] lima ff300000.gpu: IRQ ppmmu2 not found
[    0.182540] lima ff300000.gpu: IRQ ppmmu3 not found
[    0.183022] lima ff300000.gpu: IRQ ppmmu4 not found
[    0.183464] lima ff300000.gpu: IRQ ppmmu5 not found
[    0.183907] lima ff300000.gpu: IRQ ppmmu6 not found
[    0.184349] lima ff300000.gpu: IRQ ppmmu7 not found
[    0.184806] lima ff300000.gpu: gp - mali450 version major 0 minor 0
[    0.185432] lima ff300000.gpu: pp0 - mali450 version major 0 minor 0
[    0.186052] lima ff300000.gpu: pp1 - mali450 version major 0 minor 0
[    0.186676] lima ff300000.gpu: IRQ pp2 not found
[    0.187093] lima ff300000.gpu: IRQ pp3 not found
[    0.187511] lima ff300000.gpu: IRQ pp4 not found
[    0.187928] lima ff300000.gpu: IRQ pp5 not found
[    0.188343] lima ff300000.gpu: IRQ pp6 not found
[    0.188763] lima ff300000.gpu: IRQ pp7 not found
[    0.189183] lima ff300000.gpu: l2 cache 8K, 4-way, 64byte cache line, 128bit external bus
[    0.189909] lima ff300000.gpu: l2 cache 64K, 4-way, 64byte cache line, 128bit external bus
[    0.191412] lima ff300000.gpu: bus rate = 163840000
[    0.191857] lima ff300000.gpu: mod rate = 163840000
[    0.192599] [drm] Initialized lima 1.0.0 20190217 for ff300000.gpu on minor 0
[    0.201944] loop: module loaded
[    0.202243] mtip32xx Version 1.3.1
[    0.206196] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[    0.212403] libphy: Fixed MDIO Bus: probed
[    0.214195] rk_gmac-dwmac ff540000.ethernet: IRQ eth_wake_irq not found
[    0.214884] rk_gmac-dwmac ff540000.ethernet: IRQ eth_lpi not found
[    0.215605] rk_gmac-dwmac ff540000.ethernet: PTP uses main clock
[    0.216181] rk_gmac-dwmac ff540000.ethernet: phy regulator is not available yet, deferred probing
[    0.218837] dwc3 ff600000.dwc3: Failed to get clk 'ref': -2
[    0.219958] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.220538] ehci-pci: EHCI PCI platform driver
[    0.221004] ehci-platform: EHCI generic platform driver
[    0.223916] ehci-platform ff5c0000.usb: EHCI Host Controller
[    0.224449] ehci-platform ff5c0000.usb: new USB bus registered, assigned bus number 1
[    0.225303] ehci-platform ff5c0000.usb: irq 31, io mem 0xff5c0000
[    0.238725] ehci-platform ff5c0000.usb: USB 2.0 started, EHCI 1.00
[    0.239997] hub 1-0:1.0: USB hub found
[    0.240378] hub 1-0:1.0: 1 port detected
[    0.241304] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.241891] ohci-platform: OHCI generic platform driver
[    0.242798] ohci-platform ff5d0000.usb: Generic Platform OHCI controller
[    0.243417] ohci-platform ff5d0000.usb: new USB bus registered, assigned bus number 2
[    0.244261] ohci-platform ff5d0000.usb: irq 32, io mem 0xff5d0000
[    0.307463] hub 2-0:1.0: USB hub found
[    0.307846] hub 2-0:1.0: 1 port detected
[    0.309457] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    0.309974] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3
[    0.310934] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[    0.311843] xhci-hcd xhci-hcd.0.auto: irq 166, io mem 0xff600000
[    0.313369] hub 3-0:1.0: USB hub found
[    0.313753] hub 3-0:1.0: 1 port detected
[    0.314539] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    0.315106] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4
[    0.315799] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    0.316467] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    0.317815] hub 4-0:1.0: USB hub found
[    0.318192] hub 4-0:1.0: 1 port detected
[    0.319256] usbcore: registered new interface driver usb-storage
[    0.319996] i2c /dev entries driver
[    0.323094] rk808 1-0018: chip id: 0x8050
[    0.331791] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    0.332377] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    0.335514] vdd_log: supplied by vdd_5v
[    0.337514] vdd_arm: supplied by vdd_5v
[    0.338131] vcc_ddr: supplied by vdd_5v
[    0.339714] vcc_io_33: supplied by vdd_5v
[    0.343125] vcc_18: supplied by vcc_io_33
[    0.346578] vcc18_emmc: supplied by vcc_io_33
[    0.350097] vdd_10: supplied by vdd_5v
[    0.359530] rk808-rtc rk808-rtc: registered as rtc0
[    0.366932] energy_model: pd0: hertz/watts ratio non-monotonically decreasing: em_cap_state 1 >= em_cap_state0
[    0.370075] sdhci: Secure Digital Host Controller Interface driver
[    0.370629] sdhci: Copyright(c) Pierre Ossman
[    0.371048] Synopsys Designware Multimedia Card Interface Driver
[    0.372221] dwmmc_rockchip ff500000.dwmmc: IDMAC supports 32-bit address mode.
[    0.372884] dwmmc_rockchip ff500000.dwmmc: Using internal DMA controller.
[    0.373485] dwmmc_rockchip ff500000.dwmmc: Version ID is 270a
[    0.374051] dwmmc_rockchip ff500000.dwmmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
[    0.374983] vcc_sd: supplied by vcc_io_33
[    0.393404] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    0.407096] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.409167] ledtrig-cpu: registered to indicate activity on CPUs
[    0.410109] usbcore: registered new interface driver usbhid
[    0.410636] usbhid: USB HID core driver
[    0.413011] NET: Registered protocol family 10
[    0.414519] Segment Routing with IPv6
[    0.415027] NET: Registered protocol family 17
[    0.415504] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.416687] 8021q: 802.1Q VLAN Support v1.8
[    0.433356] rk_gmac-dwmac ff540000.ethernet: IRQ eth_wake_irq not found
[    0.433953] rk_gmac-dwmac ff540000.ethernet: IRQ eth_lpi not found
[    0.434598] rk_gmac-dwmac ff540000.ethernet: PTP uses main clock
[    0.435379] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input).
[    0.436003] rk_gmac-dwmac ff540000.ethernet: TX delay(0x24).
[    0.436503] rk_gmac-dwmac ff540000.ethernet: RX delay(0x18).
[    0.437009] rk_gmac-dwmac ff540000.ethernet: integrated PHY? (no).
[    0.437590] rk_gmac-dwmac ff540000.ethernet: cannot get clock clk_mac_speed
[    0.438199] rk_gmac-dwmac ff540000.ethernet: clock input from PHY
[    0.443764] rk_gmac-dwmac ff540000.ethernet: init for RGMII
[    0.444582] rk_gmac-dwmac ff540000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[    0.445226] rk_gmac-dwmac ff540000.ethernet:         DWMAC1000
[    0.445688] rk_gmac-dwmac ff540000.ethernet: DMA HW capability register supported
[    0.446343] rk_gmac-dwmac ff540000.ethernet: RX Checksum Offload Engine supported
[    0.447050] rk_gmac-dwmac ff540000.ethernet: COE Type 2
[    0.447510] rk_gmac-dwmac ff540000.ethernet: TX Checksum insertion supported
[    0.448123] rk_gmac-dwmac ff540000.ethernet: Wake-Up On Lan supported
[    0.448691] rk_gmac-dwmac ff540000.ethernet: Normal descriptors
[    0.449210] rk_gmac-dwmac ff540000.ethernet: Ring mode enabled
[    0.449719] rk_gmac-dwmac ff540000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    0.450598] libphy: stmmac: probed
[    0.511038] random: fast init done
[    0.516597] rk3328-dmc-freq dmc: current ATF version 0x101
[    0.654735] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[    0.992927] dwmmc_rockchip ff500000.dwmmc: Busy; trying anyway
[    1.493461] mmc_host mmc0: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    1.496289] rk808-rtc rk808-rtc: setting system clock to 2016-01-21T08:52:11 UTC (1453366331)
[    1.498392] Waiting for root device PARTUUID=5452574f-02...

[    1.530456] mmc0: error -110 whilst initialising SD card

[    2.031822] dwmmc_rockchip ff500000.dwmmc: Busy; trying anyway
[    2.532353] mmc_host mmc0: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    2.546995] mmc_host mmc0: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[    3.076233] dwmmc_rockchip ff500000.dwmmc: Busy; trying anyway
[    3.576766] mmc_host mmc0: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    3.591248] mmc_host mmc0: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[    4.128713] dwmmc_rockchip ff500000.dwmmc: Busy; trying anyway
[    4.629248] mmc_host mmc0: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    4.642729] mmc_host mmc0: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
[    5.200313] dwmmc_rockchip ff500000.dwmmc: Busy; trying anyway
[    5.700844] mmc_host mmc0: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[   31.714760] vcc_sd: disabling

三、猜测

看上述报错信息，似乎是TF卡没有被正确加载，进而怀疑是RK3328不兼容该TF卡。但随后测试的orangepi官方openwrt以及debain均能正常boot进入系统和正常工作，因此此项怀疑不成立，那么是镜像自身的兼容性问题吗？

欢迎大家讨论！

[Engrtao]

问题解决了，我也是这样的情况

[LCW0NJUPT]

问题解决了，我也是这样的情况

请问您是如何解决的呢？我昨晚尝试了24号的版本，依然是这个报错的。

[lituo666]

我也是遇到这个问题了，请问大佬们怎么解决呢？

[LCW0NJUPT]

我也是遇到这个问题了，请问大佬们怎么解决呢？

我更换了凯侠的TF卡就行了，这个固件似乎和闪迪的卡不兼容。

[lituo666]

我也是遇到这个问题了，请问大佬们怎么解决呢？

我更换了凯侠的TF卡就行了，这个固件似乎和闪迪的卡不兼容。 谢谢，我试试

[lituo666]

我试了 夏科 的TF卡，可以使用

[LCW0NJUPT]

我试了 夏科 的TF卡，可以使用

请问你用的是哪款设备呢，我用的是orangepi R1plus，不兼容的现象很有趣，想看一下是不是只有这一款设备出现这种情况

[lituo666]

我试了 夏科 的TF卡，可以使用

请问你用的是哪款设备呢，我用的是orangepi R1plus，不兼容的现象很有趣，想看一下是不是只有这一款设备出现这种情况

也是orangepi R1 plus ，我之前用到Lean的固件使用闪迪tf卡，夏科的卡就不行。现在换这个固件就只能用夏科的tf卡，用闪迪的tf卡和你的情况是一样的。

[Pearlfish-H]

我试了 夏科 的TF卡，可以使用

请问你用的是哪款设备呢，我用的是orangepi R1plus，不兼容的现象很有趣，想看一下是不是只有这一款设备出现这种情况

我也是 R1 Plus。我测试了两款闪迪卡：Ultra 32GB 和 Industrial 8GB，都无法正常启动。看了你的评论，我打算换凯侠试试。

[isyekong]

同样的问题，闪迪卡无法启动