search

sui77 / rc-switch

Arduino lib to operate 433/315Mhz devices like power outlet sockets.
1.92k stars 663 forks source link

no code shows when remote is activated #423

Open schaffertown opened 3 years ago

schaffertown commented 3 years ago

I am using a nano and a 315 mhz receiver with 5 different remotes. I have used simple and advanced receive demos with no success. I have an antenna soldered on the board and have it wired to pin d2, power and ground. I bought a 5 pack of boards none have worked. What am I missing?

pierzogad commented 3 years ago

Are you sure that:

Try pulling my branch https://github.com/pierzogad/rc-switch/tree/receiving-patch/examples/ReceiveDemo_Advanced this will allow you to see nonstandard timing output.

schaffertown commented 3 years ago

Thank you for the response. I found that if I hold the 4 button 433mhz remote 1 inch or closer to the board without the antenna it will pick up 2 of the 4 buttons. None of my garage door openers pick up on any of my boards315 or 433 with or without antennas. I tried the code you have. I get error codes on these 2 lines. mySwitch.setReceiveUsingProtocolTiming(false);

mySwitch.setReceiveUnknownProtocol(true);

C:\Users\Michael\Documents\Arduino\sketch_may24a\sketch_may24a.ino: In function 'void setup()': sketch_may24a:20:12: error: 'class RCSwitch' has no member named 'setReceiveUsingProtocolTiming'; did you mean 'getReceivedProtocol'? mySwitch.setReceiveUsingProtocolTiming(false); ^~~~~~~~~ getReceivedProtocol sketch_may24a:22:12: error: 'class RCSwitch' has no member named 'setReceiveUnknownProtocol'; did you mean 'getReceivedProtocol'? mySwitch.setReceiveUnknownProtocol(true); ^~~~~~~~~ getReceivedProtocol C:\Users\Michael\Documents\Arduino\sketch_may24a\sketch_may24a.ino: In function 'void loop()': sketch_may24a:27:5: error: 'output' was not declared in this scope output(mySwitch.getReceivedValue(), mySwitch.getReceivedBitlength(), mySwitch.getReceivedDelay(), mySwitch.getReceivedRawdata(),mySwitch.getReceivedProtocol()); ^~ exit status 1 'class RCSwitch' has no member named 'setReceiveUsingProtocolTiming'; did you mean 'getReceivedProtocol'?

I am not sure what it is asking me to do. the original code loads fine. Is there a chance the rcswitch library did not install propperly from the library manager?

pierzogad commented 3 years ago

I was refering to my modified clone of original code https://github.com/pierzogad/rc-switch/tree/receiving-patch Unfortunatelly these changes are not part of "official" deployment yet.

To use this code you need to clone my repository into arduino's library directory using git.

Quick and dirty way to do it would also be:

  1. Find RCSwitch.cpp and RCSwitch.h files on your computer (My Documents -> Arduino -> libraries -> rc-switch)
  2. replace these files with https://github.com/pierzogad/rc-switch/blob/receiving-patch/RCSwitch.cpp and https://github.com/pierzogad/rc-switch/blob/receiving-patch/RCSwitch.h respectively.

Once you've finished your tests you may re-install library in library manager to revert to original.

schaffertown commented 3 years ago

Thank you. I was able to get all the signals to show up in serial monitor. The range is terrible. Without an antenna soldered on 1 inch range, with an antenna 18 inches range. The voltage from my computer's usb is 4.3 volts. If that is as good as it gets I will need to buy a Receiver made for 433 or 315 openers.