Frsky vario/altimeter reset altitude

[GoogleCodeExporter]

With Frysky hub and vario attached. Absolute see level altitude show on display.

To measure relative altitude we need to reset to zero. The altitude 
programatically.

Best Regards
Tamas

PS FLD-02 has a same feature for this.

Original issue reported on code.google.com by tamasvar...@gmail.com on 7 Jan 2012 at 9:06

[GoogleCodeExporter]

This makes perfect sense. 

Bertrand ... I've assigned this to you because you understand the menu 
structures so much better than me. I think the simplest way to do it would be 
to make the ALT: field "editable" such that going to it and pressing [MENU] 
will reset it. (This is the came as the "Cal" field works on the TRAINER 
screen, for example.)

If you're too busy with more important stuff (by your own judgement of course) 
then please either assign it back to me to try and fix some time soon -- or 
just leave it until you have time. Thanks. 

Original comment by gru...@gmail.com on 8 Jan 2012 at 5:31

• Changed state: Accepted

[GoogleCodeExporter]

Yes, this one is for me. I remember asking to somebody to open it in the 
project page.
I had in mind a simple reset to 0 on the screnn, by pressing the [EXIT SHORT] 
button. Just as we do with timers, and min + max recordings in these telemetry 
screens.

Original comment by bson...@gmail.com on 9 Jan 2012 at 9:14

[GoogleCodeExporter]

Hi,

MAX record would be awesome!!! Also with reset together with altitude.

Best regards
Tamas

Also i have a few feature in my mind, for example, motor cut off on a certain 
altitude. And simple time limited motor cut off, these are would be very useful 
for ALES and LMR practicing or competition.

Original comment by tamasvar...@gmail.com on 9 Jan 2012 at 10:24

[GoogleCodeExporter]

Max: I will do
Virtual Switch based on all sensors results: will do
Simple time limited motor cut off: could you explain, it's dangerous, no?

Original comment by bson...@gmail.com on 9 Jan 2012 at 10:29

[GoogleCodeExporter]

Hi,

There are a quite lot LMR(limited motor run) glider competitions where 
programatically 
cut off the motor after a certain seconds ususally 30-45s. Then forbidden to 
restart the motor, just in emergency case, or you get 0 points.

Its interesing to make an option to use "one-shot" mixes. To active the mix 
only one time from timer/sensor values. :)

Best Regads 
Tamas

Original comment by tamasvar...@gmail.com on 9 Jan 2012 at 12:56

[GoogleCodeExporter]

Funny feature, I will do :)

Original comment by bson...@gmail.com on 9 Jan 2012 at 1:05

[GoogleCodeExporter]

E'hem! ... actually, good sir, perhaps you could discuss with the other team 
members before doing any of this? "Feature creep is our arch enemy!"

I do support it all in principal though -- especially the altitude part.

Original comment by gru...@gmail.com on 10 Jan 2012 at 12:12

[GoogleCodeExporter]

Hi,

Sorry i dont want to rush you, these are just ideas with very very nice to have 
feelings :)  

If you want i can write another nice to have feature req to keep in mind these.

One quesition, will it fit for the original hw?

Best Regards

Tamas

Original comment by tamasvar...@gmail.com on 10 Jan 2012 at 8:25

[GoogleCodeExporter]

Port done from open9x. Also all features described in this issue are 
implemented. Fully tested by Tamas himself. Let-me know if/when you would like 
them to happen in gruvin9x and I will do the port.

Original comment by bson...@gmail.com on 23 Feb 2012 at 1:40

• Changed state: Fixed