Closed CAReeser closed 5 years ago
Guess it would help if I included this: ``tinyg [mm] ok> $$ [fb] firmware build 440.20 [fv] firmware version 0.97 [hp] hardware platform 1.00 [hv] hardware version 8.00 [id] TinyG ID 7W4698-3NE [ja] junction acceleration 100000 mm [ct] chordal tolerance 0.0100 mm [sl] soft limit enable 0 [st] switch type 0 [0=NO,1=NC] [mt] motor idle timeout 2.00 Sec [ej] enable json mode 0 [0=text,1=JSON] [jv] json verbosity 2 [0=silent,1=footer,2=messages,3=configs,4=linenum,5=verbose] [js] json serialize style 1 [0=relaxed,1=strict] [tv] text verbosity 1 [0=silent,1=verbose] [qv] queue report verbosity 0 [0=off,1=single,2=triple] [sv] status report verbosity 0 [0=off,1=filtered,2=verbose] [si] status interval 500 ms [ec] expand LF to CRLF on TX 0 [0=off,1=on] [ee] enable echo 0 [0=off,1=on] [ex] enable flow control 1 [0=off,1=XON/XOFF, 2=RTS/CTS] [baud] USB baud rate 5 [1=9600,2=19200,3=38400,4=57600,5=115200,6=230400] [net] network mode 0 [0=master] [gpl] default gcode plane 0 [0=G17,1=G18,2=G19] [gun] default gcode units mode 1 [0=G20,1=G21] [gco] default gcode coord system 1 [1-6 (G54-G59)] [gpa] default gcode path control 2 [0=G61,1=G61.1,2=G64] [gdi] default gcode distance mode 1 [0=G90,1=G91] [1ma] m1 map to axis 0 [0=X,1=Y,2=Z...] [1sa] m1 step angle 1.800 deg [1tr] m1 travel per revolution 2.0000 mm [1mi] m1 microsteps 8 [1,2,4,8] [1po] m1 polarity 0 [0=normal,1=reverse] [1pm] m1 power management 3 [0=disabled,1=always on,2=in cycle,3=when moving] [2ma] m2 map to axis 1 [0=X,1=Y,2=Z...] [2sa] m2 step angle 1.800 deg [2tr] m2 travel per revolution 2.0000 mm [2mi] m2 microsteps 8 [1,2,4,8] [2po] m2 polarity 0 [0=normal,1=reverse] [2pm] m2 power management 3 [0=disabled,1=always on,2=in cycle,3=when moving] [3ma] m3 map to axis 2 [0=X,1=Y,2=Z...] [3sa] m3 step angle 1.800 deg [3tr] m3 travel per revolution 2.0000 mm [3mi] m3 microsteps 8 [1,2,4,8] [3po] m3 polarity 0 [0=normal,1=reverse] [3pm] m3 power management 3 [0=disabled,1=always on,2=in cycle,3=when moving] [4ma] m4 map to axis 3 [0=X,1=Y,2=Z...] [4sa] m4 step angle 1.800 deg [4tr] m4 travel per revolution 2.0000 mm [4mi] m4 microsteps 8 [1,2,4,8] [4po] m4 polarity 0 [0=normal,1=reverse] [4pm] m4 power management 3 [0=disabled,1=always on,2=in cycle,3=when moving] [xam] x axis mode 1 [standard] [xvm] x velocity maximum 4000 mm/min [xfr] x feedrate maximum 4000 mm/min [xtn] x travel minimum 0.000 mm [xtm] x travel maximum 370.000 mm [xjm] x jerk maximum 1 mm/min^3 1 million [xjh] x jerk homing 1 mm/min^3 1 million [xjd] x junction deviation 0.0500 mm (larger is faster) [xsn] x switch min 1 [0=off,1=homing,2=limit,3=limit+homing] [xsx] x switch max 0 [0=off,1=homing,2=limit,3=limit+homing] [xsv] x search velocity 400 mm/min [xlv] x latch velocity 30 mm/min [xlb] x latch backoff 20.000 mm [xzb] x zero backoff 0.000 mm [yam] y axis mode 1 [standard] [yvm] y velocity maximum 4000 mm/min [yfr] y feedrate maximum 4000 mm/min [ytn] y travel minimum 0.000 mm [ytm] y travel maximum 370.000 mm [yjm] y jerk maximum 1 mm/min^3 1 million [yjh] y jerk homing 1 mm/min^3 1 million [yjd] y junction deviation 0.0500 mm (larger is faster) [ysn] y switch min 1 [0=off,1=homing,2=limit,3=limit+homing] [ysx] y switch max 0 [0=off,1=homing,2=limit,3=limit+homing] [ysv] y search velocity 400 mm/min [ylv] y latch velocity 30 mm/min [ylb] y latch backoff 20.000 mm [yzb] y zero backoff 0.000 mm [zam] z axis mode 1 [standard] [zvm] z velocity maximum 4000 mm/min [zfr] z feedrate maximum 4000 mm/min [ztn] z travel minimum 0.000 mm [ztm] z travel maximum 370.000 mm [zjm] z jerk maximum 1 mm/min^3 1 million [zjh] z jerk homing 1 mm/min^3 1 million [zjd] z junction deviation 0.0500 mm (larger is faster) [zsn] z switch min 1 [0=off,1=homing,2=limit,3=limit+homing] [zsx] z switch max 0 [0=off,1=homing,2=limit,3=limit+homing] [zsv] z search velocity 400 mm/min [zlv] z latch velocity 30 mm/min [zlb] z latch backoff 20.000 mm [zzb] z zero backoff 0.000 mm [aam] a axis mode 1 [standard] [avm] a velocity maximum 4000 deg/min [afr] a feedrate maximum 4000 deg/min [atn] a travel minimum 0.000 deg [atm] a travel maximum 370.000 deg [ajm] a jerk maximum 1 deg/min^3 1 million [ajh] a jerk homing 1 deg/min^3 1 million [ajd] a junction deviation 0.0500 deg (larger is faster) [ara] a radius value 0.1989 deg [asn] a switch min 1 [0=off,1=homing,2=limit,3=limit+homing] [asx] a switch max 0 [0=off,1=homing,2=limit,3=limit+homing] [asv] a search velocity 400 deg/min [alv] a latch velocity 30 deg/min [alb] a latch backoff 20.000 deg [azb] a zero backoff 0.000 deg [bam] b axis mode 0 [disabled] [bvm] b velocity maximum 3600 deg/min [bfr] b feedrate maximum 3600 deg/min [btn] b travel minimum -1.000 deg [btm] b travel maximum -1.000 deg [bjm] b jerk maximum 20 deg/min^3 1 million [bjd] b junction deviation 0.0500 deg (larger is faster) [bra] b radius value 1.0000 deg [cam] c axis mode 0 [disabled] [cvm] c velocity maximum 3600 deg/min [cfr] c feedrate maximum 3600 deg/min [ctn] c travel minimum -1.000 deg [ctm] c travel maximum -1.000 deg [cjm] c jerk maximum 20 deg/min^3 1 million [cjd] c junction deviation 0.0500 deg (larger is faster) [cra] c radius value 1.0000 deg [p1frq] pwm frequency 100 Hz [p1csl] pwm cw speed lo 1000 RPM [p1csh] pwm cw speed hi 2000 RPM [p1cpl] pwm cw phase lo 0.125 [0..1] [p1cph] pwm cw phase hi 0.200 [0..1] [p1wsl] pwm ccw speed lo 1000 RPM [p1wsh] pwm ccw speed hi 2000 RPM [p1wpl] pwm ccw phase lo 0.125 [0..1] [p1wph] pwm ccw phase hi 0.200 [0..1] [p1pof] pwm phase off 0.100 [0..1] [g54x] g54 x offset 0.000 mm [g54y] g54 y offset 0.000 mm [g54z] g54 z offset 0.000 mm [g54a] g54 a offset 0.000 deg [g54b] g54 b offset 0.000 deg [g54c] g54 c offset 0.000 deg [g55x] g55 x offset 75.000 mm [g55y] g55 y offset 75.000 mm [g55z] g55 z offset 0.000 mm [g55a] g55 a offset 0.000 deg [g55b] g55 b offset 0.000 deg [g55c] g55 c offset 0.000 deg [g56x] g56 x offset 0.000 mm [g56y] g56 y offset 0.000 mm [g56z] g56 z offset 0.000 mm [g56a] g56 a offset 0.000 deg [g56b] g56 b offset 0.000 deg [g56c] g56 c offset 0.000 deg [g57x] g57 x offset 0.000 mm [g57y] g57 y offset 0.000 mm [g57z] g57 z offset 0.000 mm [g57a] g57 a offset 0.000 deg [g57b] g57 b offset 0.000 deg [g57c] g57 c offset 0.000 deg [g58x] g58 x offset 0.000 mm [g58y] g58 y offset 0.000 mm [g58z] g58 z offset 0.000 mm [g58a] g58 a offset 0.000 deg [g58b] g58 b offset 0.000 deg [g58c] g58 c offset 0.000 deg [g59x] g59 x offset 0.000 mm [g59y] g59 y offset 0.000 mm [g59z] g59 z offset 0.000 mm [g59a] g59 a offset 0.000 deg [g59b] g59 b offset 0.000 deg [g59c] g59 c offset 0.000 deg [g92x] g92 x offset 0.000 mm [g92y] g92 y offset 0.000 mm [g92z] g92 z offset 0.000 mm [g92a] g92 a offset 0.000 deg [g92b] g92 b offset 0.000 deg [g92c] g92 c offset 0.000 deg [g28x] g28 x position 0.000 mm [g28y] g28 y position 0.000 mm [g28z] g28 z position 0.000 mm [g28a] g28 a position 0.000 deg [g28b] g28 b position 0.000 deg [g28c] g28 c position 0.000 deg [g30x] g30 x position 0.000 mm [g30y] g30 y position 0.000 mm [g30z] g30 z position 0.000 mm [g30a] g30 a position 0.000 deg [g30b] g30 b position 0.000 deg [g30c] g30 c position 0.000 deg
what does "File not open" mean and why am I getting this error? Web page has no explanation. Also, it appears that the command is not being accepted, yet the status on $$ indicates that it has. Thanks, Cliff:
$gdi=0 {"er":{"fb":440.20,"st":9,"msg":"File not open"}} [gdi] default gcode distance mode 0 [0=G90,1=G91] tinyg [mm] ok>`
Also, the $gdi=0 is issued in minicom, more than once, with the same error. Therefore, there is no eeprom write occurring to cause this.
Interesting, although a soft reboot and/or $defa=1 does NOT allow a $gdi change, a physical- push- the- red- button will allow the $gdi=1 to take effect.
issuing 'M2' restores expected $gdi=1 operation. Is one of my init commands putting me into program mode so that some of my init commands are not being acted upon?
OK, so, in order for some initialization parameters to take effect, I must issue an m2, reset, or reboot. And, the $$ report shows the current operating mode, not necessarily the settings that were just sent.
Question: Are there any settings that are not maintained across a reboot/reset?
Something in my initialization will not allow g91. The setting $$ in the tinyg says gdi=1, but the motor does not move incrementally. Toggling the setting does not help in minicom. Thanks, Cliff
["$gun=1", "$1ma=0", "$2ma=1", "$3ma=2", "$4ma=3", "$xam=1", "$yam=1", "$zam=1", "$aam=1", "$1sa=1.8", "$2sa=1.8", "$3sa=1.8", "$4sa=1.8", "$1tr=2.0", "$2tr=2.0", "$3tr=2.0", "$4tr=2.0", "$1pm=3", "$2pm=3", "$3pm=3", "$4pm=3", "$xjm=1", "$yjm=1", "$zjm=1", "$ajm=1", "$xjh=1", "$yjh=1", "$zjh=1", "$ajh=1", "$xvm=4000", "$yvm=4000", "$zvm=4000", "$avm=4000", "$xfr=4000", "$yfr=4000", "$zfr=4000", "$afr=4000", "$xtm=370", "$ytm=370", "$ztm=370", "$atm=370", "$xtn=0", "$ytn=0", "$ztn=0", "$atn=0", "$xSV=400", "$ySV=400", "$zSV=400", "$aSV=400", "$ej=0", "$tv=1", "$qv=0", "$sv=0", "$gdi=1", "$xlv=30", "$ylv=30", "$zlv=30", "$alv=30", " $xzb=0", "$yzb=0", "$zzb=0", "$azb=0", "$st=0", "$xsx=0", "$ysx=0", "$zsx=0", "$asx=0", "$1po=0", "$2po=0", "$3po=0","$4po=0"]