search

techiesms / ESP32-ChatGPT

This Repo contains the code for using ChatGPT on ESP32 board along with Audio Response using i2s amplifier module
131 stars 48 forks source link

Guru Meditation Error: Core 1 panic'ed (LoadProhibited). Exception was unhandled. #5

Open Athiga99 opened 11 months ago

Athiga99 commented 11 months ago

i have done the hardware setup ,and dumped the code in both ESP32 but while I run the project it does not work properly , when I ask questions it does not responding ,

this is the serial monitor data, how to rectify this and how to complete my project

Rebooting... ets Jul 29 2019 12:21:46

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:1216 ho 0 tail 12 room 4 load:0x40080400,len:6388 entry 0x400806b4 Press button

Record start!

Recoding Complited Processing Json daata---

Guru Meditation Error: Core 1 panic'ed (LoadProhibited). Exception was unhandled. Core 1 register dump: PC : 0x4000c677 PS : 0x00060e30 A0 : 0x800d18c9 A1 : 0x3ffb1560
A2 : 0x00000000 A3 : 0x3f4002aa A4 : 0x3ffc6284 A5 : 0xddf299c4
A6 : 0x3fff3888 A7 : 0x3fff38d3 A8 : 0x800d5dd8 A9 : 0x3ffb1540
A10 : 0x00000002 A11 : 0x3f40026d A12 : 0x00000000 A13 : 0x00000000
A14 : 0x00000007 A15 : 0x00000066 SAR : 0x00000010 EXCCAUSE: 0x0000001c
EXCVADDR: 0x00000000 LBEG : 0x400014fd LEND : 0x4000150d LCOUNT : 0xffffffff

ELF file SHA256: 0000000000000000

Backtrace: 0x4000c677:0x3ffb1560 0x400d18c6:0x3ffb1580 0x400d22df:0x3ffb1f90 0x400d7aa0:0x3ffb1fb0 0x400899f6:0x3ffb1fd0

techiesms commented 7 months ago

Looking at your Serial Monitor data, I can conclude that the ESP32 board is not getting data from microphone. So kindly try out below mentioned steps and see the results

muhammadmemon749 commented 7 months ago

Looking at your Serial Monitor data, I can conclude that the ESP32 board is not getting data from microphone. So kindly try out below mentioned steps and see the results

  • Try to speak louder and see if you are getting the results
  • Check the connections and make sure all the pins of microphone are getting proper connectivity with ESP32
  • Check the Vcc and Gnd pin of Mic and see if it is getting the proper voltage
  • If nothing works, try changing the microphone and test

I am running into the same issue and replaced three microphones and I have connected the microphone according to the semantic diagram, please guide me on what possible steps I can take.